Viega PreVista Dry Plus 8565 User manual

for wall-mounted flushing valve
Model Year built:
8565 from 12/2018
en_INT
Prevista Dry Plus urinal module
Instructions for Use

Prevista Dry Plus urinal module 2 from 12

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
2.2.2 Compatible components 6
3Handling 7
3.1 Assembly information 7
3.1.1 Installation dimensions 7
3.2 Assembly 8
3.2.1 Mounting module 8
3.2.2 Setting up and cladding the module 11
3.3 Disposal 12
Table of contents
Prevista Dry Plus urinal module 3 from 12

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista Dry Plus urinal module 4 from 12

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Dry Plus urinal module 5 from 12

2 Product information
2.1 Intended use
2.1.1 Areas of use
The Prevista Dry Plus urinal module is designed for mounting in a Pre‐
vista Dry Plus pre-wall construction.
2.2 Product description
2.2.1 Overview
..

Fig. 1: Components and scope of delivery
1 Urinal module
2 Screws for fixing in support profile
3 slot nuts
4 Assembly accessories wall plates
5 Threaded rods and protective caps for fixing sanitary objects
2.2.2 Compatible components
The urinal module is compatible with the ceramics for flush valve.
Product information
Prevista Dry Plus urinal module 6 from 12

3 Handling
3.1 Assembly information
3.1.1 Installation dimensions
NBY


Handling
Prevista Dry Plus urinal module 7 from 12

3.2 Assembly
3.2.1 Mounting module
Secure the module onto the open mounting rail with the slot nuts
supplied:
Insert the slot nut into the opening of the module.
Push the slot nut in until it engages.
Set the height of the rails.
Handling
Prevista Dry Plus urinal module 8 from 12

Fasten the slot nut.
Bend the sides of the metal bars of the rails.
Bend the sides of the metal bars of the fitting holder.
Bend the sides of the metal bars of the drain elbow.
25 Nm
Handling
Prevista Dry Plus urinal module 9 from 12

Set the height of the module according to the ceramic manufactur‐
er's instructions.
The projection of the carriers beyond the rails is maximum 1.5 mm.

99
İ
Handling
Prevista Dry Plus urinal module 10 from 12

3.2.2 Setting up and cladding the module
Mount a drain elbow.
Turn in the threaded rods by hand.
Tighten the nuts of the threaded rods with a fork spanner.
Place the protective caps on the threaded rods.
Make the water connections.
Cut out the recesses for the drain elbow and the threaded rods.
Cut the gypsum cardboard cladding panel to size.
.
W
J
F
H
B
.
ς
W
J
F
H
B
.
Handling
Prevista Dry Plus urinal module 11 from 12

Clad the module with suitable gypsum cardboard cladding panels.
3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Prevista Dry Plus urinal module 12 from 12