Viega Prevista 8640.14 User manual

for Prevista remote flush actuations
Model Year built:
8640.14 from 03/2019
en_INT
Prevista installation set
Instructions for Use

Prevista installation set 2 from 10

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
3Handling 7
3.1 Assembly 7
3.2 Disposal 10
Table of contents
Prevista installation set 3 from 10

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista installation set 4 from 10

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista installation set 5 from 10

2 Product information
2.1 Intended use
2.1.1 Areas of use
The Prevista installation set is required for the installation of WC remote
flush actuations for Prevista.
2.2 Product description
2.2.1 Overview

Fig. 1: Scope of delivery
1 Concealed socket
2 Screws and plates for fixing
3 Protective pipe
Product information
Prevista installation set 6 from 10

3 Handling
3.1 Assembly
Requirements:
nThe maximum cable length is 3 m.
– Factor in at least 0.25 m for the cistern.
nThe distances conform to the specifications:
Fasten the screws and securing plates in the concealed socket.
Push through the concealed socket at the pre-punched location.
NN
Handling
Prevista installation set 7 from 10

WC element, construction height 1120 mm or 980 mm
Cut in the cap crosswise for the free water connection.
Insert the empty pipe into the cistern.
WC element, construction height 820 mm
Route the empty pipe through the shower WC connection into the
cistern.
WC element, construction height 820 mm without shower WC con‐
nection
Insert the empty pipe into the cistern from below.
Cut in the cap crosswise for the free water connection.
Drill the recess for the empty pipe in the gypsum cladding panel.
Route the empty pipe outside.




Handling
Prevista installation set 8 from 10

Cut out the template for the remote flush actuation from the accom‐
panying instructions.
Cut the recess for the empty pipe from the template.
Route the empty pipe through the template.
Position the template on the gypsum cladding panel.
Route the empty pipe through the concealed socket.
Push the concealed socket onto the template and corn the gypsum
cardboard cladding panel by applying gentle pressure.
Cut the recesses for the concealed socket.
Insert the concealed socket into the gypsum cladding panel.
Handling
Prevista installation set 9 from 10

Screw on the concealed socket.
3.2 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Prevista installation set 10 from 10