Viega 8570 User manual

for Prevista Dry Plus fitting holder and module
Model Year built:
8570 from 03/2019
en_INT
Prevista Dry frame element
Instructions for Use

Prevista Dry frame element 2 from 14

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
3Handling 7
3.1 Assembly information 7
3.1.1 Installation dimensions 7
3.2 Assembly 8
3.2.1 Mounting the element 8
3.2.2 Mounting the fitting holder 12
3.3 Disposal 14
Table of contents
Prevista Dry frame element 3 from 14

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista Dry frame element 4 from 14

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Dry frame element 5 from 14

2 Product information
2.1 Intended use
2.1.1 Areas of use
The Prevista Dry frame element is suitable for Prevista Dry Plus fitting
holders and modules.
2.2 Product description
2.2.1 Overview

Fig. 1: Component overview
1 Prevista Dry frame element
2 Screws for fixing
3 quick-release clamp
4 slot nuts
Product information
Prevista Dry frame element 6 from 14

3 Handling
3.1 Assembly information
3.1.1 Installation dimensions


Handling
Prevista Dry frame element 7 from 14

3.2 Assembly
3.2.1 Mounting the element
Determine and mark the fixing points.
nX2: 460 mm
Drill the holes.
Insert the dowels.
Determine and mark the fixing points on the floor.
nX3: 375 mm
Drill the holes.
Insert the dowels.
INFO! Mount the Prevista Dry fixing set pursuant to the instruc‐
tions for use for the fixing set.
Loosen the feet of the element using a fork spanner.
Mounting to a masonry wall
煼
9
9
Handling
Prevista Dry frame element 8 from 14

Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
nX: 1000 mm
Tighten the feet of the element using a fork spanner.
ðThe element is attached to the wall.
Mount the Prevista Dry Plus pre-wall construction pursuant
to the instructions for use of the Prevista Dry Plus system.
Position the element on the floor rail.
Fix the feet on the floor rail using the clips.
Mounting in Prevista Dry Plus


Handling
Prevista Dry frame element 9 from 14

Set the height of the element by means of the feet.
Fix the element with the Prevista Dry Plus Steptec rail connectors.
ðThe element is fixed in the Prevista Dry Plus pre-wall construc‐
tion.
Handling
Prevista Dry frame element 10 from 14

Position the element on the floor rail.
If necessary, adjust the foot depth from 50 mm (pre-mounted) to 75
mm.
Pull the foot out and turn by 90°.
Screw the feet together with the support profile.
Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
nX: 1000 mm
Attach the element to the support profiles using the screws sup‐
plied.
Mounting in metal support profile

d

9

YY
Handling
Prevista Dry frame element 11 from 14

If applicable, connect further elements to the element via the sup‐
port profile.
3.2.2 Mounting the fitting holder
Open the quick-release lever.
Turn the lever 90° anti-clockwise.
d
Handling
Prevista Dry frame element 12 from 14

Insert the quick release through the fitting holder and into the ele‐
ment.
Turn the quick-release lever 90° anti-clockwise.
Close the quick-release lever.
Repeat these steps on the other side.
ðThe fitting holder is fastened in the element.
d
Handling
Prevista Dry frame element 13 from 14

3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Prevista Dry frame element 14 from 14