Viega Steptec 8467.3 User manual

Viega Steptec
Model Year built:
8467.3 from 03/2009
en_INT
Viega Steptec bidet module
Instructions for Use

Viega Steptec bidet module 2 from 12

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Standards and regulations 6
2.2 Intended use 6
2.2.1 Areas of use 6
2.3 Product description 7
2.3.1 Overview 7
2.3.2 Compatible components 7
2.3.3 Sound protection 7
3Handling 8
3.1 Assembly information 8
3.1.1 Mounting conditions 8
3.1.2 Installation dimensions 9
3.1.3 Required tools 9
3.2 Assembly 9
3.2.1 Mounting module 9
3.2.2 Rounding off jobs 12
3.3 Disposal 12
Table of contents
Viega Steptec bidet module 3 from 12

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Viega Steptec bidet module 4 from 12

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand-
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Viega Steptec bidet module 5 from 12

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger-
many
suitable masonry walls EN 1996-1-1
suitable concreted walls DIN 1045
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger-
many
Fulfilled noise protection require-
ments
DIN 4109
Fulfilled noise protection require-
ments
DIN 4109 (additional sheet 2)
Fulfilled noise protection require-
ments
VDI 4100 SSt I-SSt II
2.2 Intended use
2.2.1 Areas of use
The Steptec bidet module is suitable for mounting on wall constructions
pursuant to the regulations in section Ä„Regulations from section:
Fields of application / Mounting conditions“ on page 6 and is intended
for use in a Steptec pre-wall construction.
Product information
Viega Steptec bidet module 6 from 12

2.3 Product description
2.3.1 Overview
1 - sanitary object fixing set
2 - wall plate (not included in scope of delivery)
3 - drainpipe
4 - slot nuts
2.3.2 Compatible components
The bidet module is compatible with common bidet ceramics, even with
larger projection (barrier-free).
2.3.3 Sound protection
The bidet module complies with the noise insulation requirements
specified in section Ä„Regulations from section: Sound protection“
on page 6 .
Product information
Viega Steptec bidet module 7 from 12

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
The Viega bidet element is suitable for mounting on masonry wall con-
structions and support profiles pursuant to the regulations in section
Ä„Regulations from section: Fields of application / Mounting condi-
tions“ on page 6 .
The bidet element may only be mounted on even wall surfaces.
For this, observe the Steptec system instructions for use.
With the construction height, the marked height of the upper edge of
the finished floor must be observed.
Errors caused by incorrect construction heights may limit
the setting range after the completion of the work. A correc-
tion and therefore a limitation of the setting range is only
possible up to max. 20 mm. The setting range is reduced
accordingly from 80 mm to 60 mm.
The bidet module can only be used in combination with wall-hung
bidets (fixing gauges for bore hole 180 mm or 230 mm).
Suitable walls
Suitable walls
Construction height
Bidet ceramic
Handling
Viega Steptec bidet module 8 from 12

3.1.2 Installation dimensions
Fig. 1: Dimensions
A - adjustable height
B - adjustable height
3.1.3 Required tools
The following tools are required for mounting the bidet module:
ndrill with 10 mm drill bit
nratchet with sockets: 13 mm / 17 mm
nfork or ring spanner: 17 mm / 19 mm
3.2 Assembly
3.2.1 Mounting module
The two vertical rails, which surround the module, must be
open towards the module and be at an interval of 430 mm.
Mounting in Steptec
Securing module
Handling
Viega Steptec bidet module 9 from 12

Secure the module onto the open Steptec rail with the slot nuts sup-
plied:
Insert the slot nut into the opening of the module.
Push the slot nut in slightly.
Turn by 90°.
ðThe slot nut is secured in the Steptec rail.
Align the height of the module.
The interval between the middle fixing level for the threaded bolts to
the UEFFL is 330 mm.
Handling
Viega Steptec bidet module 10 from 12

Tighten the slot nut with a ring spanner (SW 17).
Tighten the other slot nuts in the same way.
ðThe module is secured on the rail framework.
Screw the threaded bolt into the threaded mount.
Set threaded bolt:
The height of the threaded bolts can be set to three levels.
The interval between both bolts can be set to 180 or 230 mm.
Lock the drainpipe in place in the holding device.
Insert seal.
Set the height of the drainpipe, if required. To do this, loosen the
screw above the pipe fixing and set the desired height. Secure with
the screw.
Handling
Viega Steptec bidet module 11 from 12

Set wall plate fixing:
Loosen screws and set the holder to the required height. Secure
with the screws.
Mount the wall plates on-site.
Make water connection.
3.2.2 Rounding off jobs
Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide
Aqua-KS cladding panels.
When doing so, make sure that no abutting edges converge.
Grout the abutting edges and joints with a suitable filler.
Observe the instruction manual for the cladding panels for more
information.
3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Viega Steptec bidet module 12 from 12