Viega Prevista Dry 8573 User manual

Single mounting of Viega Prevista Dry elements on a solid wall
Model
8573
en_INT
Prevista Dry fixing set
Instructions for Use

Prevista Dry fixing set 2 from 11

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Standards and regulations 6
2.2 Intended use 6
2.2.1 Areas of use 6
2.3 Product description 7
2.3.1 Overview 7
3Handling 8
3.1 Assembly 8
3.1.1 Mounting the fixing set 8
3.2 Disposal 11
Table of contents
Prevista Dry fixing set 3 from 11

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista Dry fixing set 4 from 11

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Dry fixing set 5 from 11

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe and
are provided as a support feature.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger‐
many
Suitable masonry walls EN 1996-1-1
Suitable concreted walls DIN 1045
2.2 Intended use
2.2.1 Areas of use
The Prevista Dry fixing set is used for mounting Prevista Dry elements
onto the wall construction pursuant to the regulation in section Ä „Reg‐
ulations from section: Fields of application / Mounting conditions“
on page 6.
Product information
Prevista Dry fixing set 6 from 11

2.3 Product description
2.3.1 Overview

Fig. 1: Components
1 Cap
2 Slide
3 Mounting bracket
4 Dowels and screws for wall mounting
5 Threaded rods
Product information
Prevista Dry fixing set 7 from 11

3 Handling
3.1 Assembly
3.1.1 Mounting the fixing set
Mount the elements as shown by way of example of the Pre‐
vista Dry WC element with shower WC connection and vari‐
able ceramic height (model 8521).
Determine and mark the fixing points.
nX1: depending on the element used.
nX2: depending on the element used.
Drill the holes.
Insert the dowels.
Mount the mounting bracket.
Loosen the feet of the element using a fork spanner (size 13).
9

9
煼
9

Handling
Prevista Dry fixing set 8 from 11

Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
Tighten the feet of the element using a fork spanner (size 13).
Align the depth of the element.
nX4: depending on the element used.
Mark the fixing points on the floor.
Remove the element and drill the floor holes.
Insert the dowels.
Fix the element in the floor.

9
9
9
煼


Handling
Prevista Dry fixing set 9 from 11

Push the mounting bracket through the element on the threaded
rods.
Align the element and use the slide to attach the mounting bracket
to the threaded rods.
Loosely insert the caps.
INFO! Do not press on the caps to engage them.
Re-adjust the alignment of the element using the threaded rods.
Handling
Prevista Dry fixing set 10 from 11

Push the caps down until they engage.
3.2 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Prevista Dry fixing set 11 from 11