Viega Multiplex Trio 6170.11 User manual

for bathtub with middle connection, water level increase plus
5 cm
Model Year built:
6170.11 from 01/2015
en_INT
Multiplex Trio drain/overflow Visign MT9
Instructions for Use

Multiplex Trio drain/overflow Visign MT9 2 from 22

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 7
2.2.1 Overview 7
2.2.2 Technical data 8
2.3 Accessories 8
3Handling 10
3.1 Assembly information 10
3.1.1 Mounting conditions 10
3.1.2 Installation dimensions 10
3.1.3 Required tools and materials 11
3.2 Assembly 12
3.2.1 Mounting overflow 12
3.2.2 Mounting the drain 14
3.2.3 Connecting overflow and drain 15
3.2.4 Connecting the wastewater system 16
3.2.5 Connecting the inlet 17
3.2.6 Mounting equipment set 18
3.2.7 Leakage test 19
3.3 Use 20
3.4 Care 22
3.5 Disposal 22
Table of contents
Multiplex Trio drain/overflow Visign MT9 3 from 22

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nOperators
nConsumers
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Multiplex Trio drain/overflow Visign MT9 4 from 22

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand-
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Multiplex Trio drain/overflow Visign MT9 5 from 22

2 Product information
2.1 Intended use
2.1.1 Areas of use
NOTICE!
Risk of damage due to unsuitable liquids
To avoid damaging the drain, only introduce the following
liquids:
– Typical household wastewater with temperatures up to
95 °C
– The pH value must be higher than 4 but lower than 10.
The Multiplex Trio drain/overflow is a combined inlet, drain and overflow
with odour trap for bathtubs with a 52 mm drain hole. The inlet flows
through the overflow opening.
The drain/overflow is suitable for bathtubs with a middle connection.
Detailed information regarding all bathtub models and the corre-
sponding Viega drains / overflows can be found in the catalogue or on
the Internet.
Product information
Multiplex Trio drain/overflow Visign MT9 6 from 22

2.2 Product description
2.2.1 Overview
The following components are included in the scope of delivery of the
Multiplex Trio drain / overflow:
14
10
11
12
13
1 2 3 4 5 6 7 8 9
2526 24 23 22 21 20 19 18 17 16 15
Fig. 1: Component overview
1 overflow unit
2 profile seal
3 double seal
4 seal
5 flange cover
6 supply flange
7 Site protection
8 fixing screw
9 rotatable rosette
10 valve cone
11 site protection
12 fixing screw
13 valve top
14 profile seal
15 drain elbow
16 union nut
17 sliding ring
18 wedge seal
19 odour trap
20 wedge seal
21 sliding ring
22 union nut
23 overflow pipe
Product information
Multiplex Trio drain/overflow Visign MT9 7 from 22

24 Bowden cable
25 sleeve
26 adapter
2.2.2 Technical data
Drainage capacity (at an accumu-
lation height of 300 mm)
0.92 l/s
Overflow capacity (at an accumu-
lation height of 60 mm)
0.55 l/s or 0.63 l/s
Inlet capacity (at 0.25 MPa
(2.5 bar))
20 l/min
Diameter of bathtub drain hole 52 mm
DN (nominal width) outlet pipe 40 / 50 mm
Length of Bowden cable 725 mm
Length 130–370 mm
Height 180–430 mm
Dimensions and installation depth
ÄChapter 3.1.2 „Installation
dimensions“ on page 10
2.3 Accessories
The accessories shown here are not included in the scope
of delivery. If required, it must be purchased separately.
Pipe interrupter
To ensure that no bath water flows back into the potable water installa-
tion, a pipe interrupter must be installed, e.g. the connection set with
concealed pipe interrupter DN 20, model 6161.86. A suitable cover
rosette for the pipe interrupter must be purchased separately.
Required accessories
Product information
Multiplex Trio drain/overflow Visign MT9 8 from 22

Multiplex extension set
It is possible to extend the odour trap below the bathtub in the case of
bathtubs with a very thick floor. The extension set, model 6161.7, is
available for such cases.
Optional accessories
Product information
Multiplex Trio drain/overflow Visign MT9 9 from 22

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
The following requirements exist for the mounting of the drain / over-
flow:
nThe bathtub is installed.
nThe drainage line is installed all the way to the bathtub.
nThe underside of the bathtub is accessible.
3.1.2 Installation dimensions
Fig. 2: Dimensional drawing
The following values are valid for L (length) and H (height):
L = 130–370
H = 180–430
Handling
Multiplex Trio drain/overflow Visign MT9 10 from 22

3.1.3 Required tools and materials
The following tools are required for mounting:
nsocket spanner (size 14)
nfine-toothed saw
nflat-blade screwdriver
No additional material is required for the complete mounting of the
product.
Tool
Material
Handling
Multiplex Trio drain/overflow Visign MT9 11 from 22

3.2 Assembly
3.2.1 Mounting overflow
Proceed as follows to the mounting of the overflow:
Push the rubber sleeve onto the pipe of the overflow unit.
The lower edge must be flush with the edge of the overflow pipe.
Fit the profile seal in the overflow unit.
If the wall thickness is smaller than 3 mm (in the case of steel bath-
tubs), insert an addition seal between profile seal and bathtub.
Join flange cover and supply flange.
Place the sealing element on the supply flange.
Fit the supply flange into the overflow unit.
>3mm
<3mm
Handling
Multiplex Trio drain/overflow Visign MT9 12 from 22

Hold the overflow unit on the overflow opening of the bathtub from
the outside.
Insert the fixing screw in the flange.
Screw the fixing screw in the overflow unit.
NOTICE! Pliers or other tools may damage the fixing screw or
the flange. Only tighten the fixing screw by hand.
Place the site protection on the flange.
Handling
Multiplex Trio drain/overflow Visign MT9 13 from 22

3.2.2 Mounting the drain
Proceed as follows to mount the drain:
Place the double seal onto the drain unit in such a way that the
recess is positioned above the connecting pipe.
Place the profile seal in the recess of the drain unit.
Mount the drain unit with profile seal on the drain hole of the
bathtub from below.
Pull the edge of the double seal over the edge of the drain.
Pull the upper part of the double seal through the drain hole.
Insert the valve top and the fixing screw.
INFO! The cross-shaped structures of the odour trap and the
valve top must be positioned parallel on top of each other to
ensure the full drainage capacity.
Tighten the fixing screw with the mounting aid.
Handling
Multiplex Trio drain/overflow Visign MT9 14 from 22

Insert the site protection.
3.2.3 Connecting overflow and drain
After the overflow and the drain have been mounted, you must connect
them both using the overflow pipe. Proceed as follows:
Requirements:
nThe overflow is mounted in the overflow opening.
nThe drain is securely mounted on the base of the bathtub.
NOTICE! Connections where the pipes are not inserted far
enough into each other become leaky. For this reason, maintain
a minimum insertion depth of 15 mm for every connection.
Hold the pipe of the overflow unit parallel to the overflow pipe and
mark the positions where the drain and the overflow should be con-
nected.
Minimum insertion depth: 15 mm
Cut the overflow pipe to the marked length and deburr it.
Push the top end of the overflow pipe into the rubber sleeve.
Minimum insertion depth: 15 mm
Push the union nut, sliding ring and seal onto the bottom end of the
drain elbow.
Screw the union nut on the drain unit.
725 mm
+>15mm
+>15mm
Handling
Multiplex Trio drain/overflow Visign MT9 15 from 22

3.2.4 Connecting the wastewater system
Proceed as follows to connect the drain/overflow to the wastewater
system:
Requirements:
nThe overflow and drain units are installed on the bathtub.
nThe connection between overflow and drain has been made.
If the wastewater pipe only has a diameter of 40 mm, cut off drain
elbow.
Push the union nut, sliding ring and seal onto the drain elbow.
Ensure that the seal is positioned securely in the recess.
Screw the union nut on the drain unit.
Align the odour trap in such a way that the drain elbow can be con-
nected to the wastewater pipe.
Push the wastewater pipe in the drain elbow.
ø 40
ø 50
Handling
Multiplex Trio drain/overflow Visign MT9 16 from 22

3.2.5 Connecting the inlet
Requirements:
nA connection set (e. g. the pipe interrupter set) is available.
nA pipe interrupter is installed in the supply pipeline.
nThe overflow and the drain are mounted.
nThe overflow and the drain are connected.
nThe connection to the wastewater system has been made.
INFO! Mounting with the Viega plug connection is described in
the following. Mounting can also be carried out with other con-
necting materials. If necessary, observe the manufacturer's
instructions.
Push the union nut and the clamping ring (parts of the connection
set) onto the water-carrying pipe.
Push the narrow end of the screw fitting (part of the connection set)
into the pipe as far as it will go.
Push the free end of the screw fitting into the connecting piece.
Use the union nut to screw the pipe tight at the connecting piece.
Insert the connecting piece into the overflow unit.
The connecting piece must click into place in the overflow unit with
a noticeable clicking sound.
Handling
Multiplex Trio drain/overflow Visign MT9 17 from 22

3.2.6 Mounting equipment set
To avoid damage to the rosette and valve cone, only mount the equip-
ment set after finishing all other work on the building site. Proceed as
follows:
Set the valve cone with the help of the adjusting screw and counter
with the nut.
Remove the red site protection.
Fit the valve cone.
Fit the rotatable rosette loosely (not all the way).
To align, turn the rotatable rosette as far as it will go to the left.
ðThe valve cone closes itself.
1
1
2
3
Handling
Multiplex Trio drain/overflow Visign MT9 18 from 22

Remove the rotatable rosette.
Fit the rotatable rosette with the flat side facing upwards.
ðThe rotatable rosette is properly aligned.
3.2.7 Leakage test
The leakage test is only carried out as a visual inspection.
Check the points marked in the following drawing with particular care:
Check the drain/overflow fitting for visible leaks.
Handling
Multiplex Trio drain/overflow Visign MT9 19 from 22

3.3 Use
The drain / overflow are controlled via the rotatable rosette on the over-
flow. Proceed as follows to open or close the drain:
Turn the rotatable rosette to the left.
ðThe drain closes itself.
Turn the rotatable rosette to the right.
ðThe drain opens itself.
Handling
Multiplex Trio drain/overflow Visign MT9 20 from 22