Viessmann VITOPLANAR User manual

6136715 GB 7/2018
Installation and
operating instructions
Wireless room temperature controller,
LCD with clock and 7-day program
VITOPLANAR wireless thermostat LCD clock
VIESMANN

2
6136715
Safety instructions
Please follow these safety instructions closely to prevent hazards,
injury and material losses.
Safety instructions explained
Danger
¨This symbol warns against the risk of injury.
Caution
! This symbol warns against the risk of material losses and
environmental pollution.
Note
Text with the word Note contains additional information.
Installation, commissioning, inspection, maintenance and repairs
must only be carried out by an authorised, competent person
(heating engineer/installation contractor).
Before working on the appliance/heating system, isolate it from the
power supply (e.g. by removing a separate fuse or by means of a
mains isolator) and safeguard against unauthorised reconnection.
Repairing components that full a safety function can compromise
the safe operation of the system.
For replacements, use only original spare parts supplied or
approved by Viessmann.

3
6136715

4
6136715
Product information
The appliance is a wireless room temperature controller with clock
for capturing the temperature in residential, o󰀩ce and hotel rooms.
Simple to install – no time-consuming chase cutting and plastering
for cable routing. The controller can be installed on a ush mounted
or surface mounted box on the wall. A support arm also enables
freestanding operation. The controller has a freely programmable
7-day program, frost protection function, manual operation and
on/o󰀨 function.

5
6136715
Installation

6
6136715
Operating and display elements
AUTO mode
Comfort mode
Setback mode
Frost protection
mode
Set the date and time /
programming
1
2
3
4
5
1
3
4
2
5
8 96 7
Time
Day
Measured temperature or
set temperature
Current set temperature
Wireless transmission
"Party" mode
Absence mode
Info button
Off mode
Temperature
setting
Standby mode:
After a certain period of inactivity, the thermostat switches to
standby mode. To exit this mode, press a button or turn the
selector switch

7
6136715
Assigning wireless receivers

8
6136715
Conguration
The thermostat must be switched off.

Press the second button from the left for 5 seconds.
The thermostat version appears on the display.

Press OK.
Menu CF01 appears on the display.

Select the required setting with + and -.
Press OK to confirm the setting and move to the next setting.
Turn the selector switch to exit the mode.
CF01 – Correction of measured temperature
Adjustable from -5
°C to +5 °C.
E
xample: If the temperature displayed by the appliance is 19 °C
and the temperature measured (by thermometer) is 20
°C, +1 °C
must be set.
CF02 – Displayed temperature in AUTO mode
0Set temperature
1 Measured temperature
>5s -5 °C -> +5 °C
1 2
3
4
Note: The fields with a grey background correspond to the
pre-configured factory settings.

9
6136715
Conguration (continued)

10
6136715
Conguration (continued)
CF08 – Open detection function
If the receiver is combined with an open detector (e.g. for a
window), the heating is switched to frost protection mode when
the window is opened.
CF09 – Presence detection function
If the receiver is combined with a motion detector, the temperature
is automatically reduced during long periods of absence:
•
1.5 hours -> current set temperature -1.5 °C
•
3.5 hours -> current set temperature -3.5 °C
•
48 hours -> set frost protection temperature
CF10 – Max. set comfort temperature
Ad
justable from 22 °C to 30 °C.
Standard value: 28
°C
CF11 – Programming format
0 Deactivated
1 Activated
0 Deactivated
1 Activated
0 Programming in 1-hourly steps
1 Programming in 1/2-hourly steps

11
6136715
Conguration (continued)
CF12 – Time format
CF13 – Automatic summer/wintertime
changeover
If CF13 = 0, the option to set the date is not offered.
CF15 – Display of window symbol
(open detection)
If CF08 = 1:
CF16 – Display of symbol
(heat demand)
0 12 h (a.m./p.m.)
1 24 h
0 Deactivated
1 Activated
0 Non-flashing symbol
1 Flashing symbol
0 Symbol not shown
1 Symbol shown

12
6136715
Conguration (continued)

13
6136715
Conguration (continued)
CF 28 – "Adaptive start control" function
Thanks to this function, the required temperature is reached at the
scheduled time.
0 Function deactivated
1 Function activated
Press +/– to activate or deactivate the function.
Conrm with OK.
You will be taken to menu CF29.
CF29 – Setting the temperature/time curve for adaptive
start control
The temperature/time curve depends on the heating system.
Adjustable from 1 to 6 °C in steps of 0.1 °C.
Factory setting: 3 °C.
If the required temperature is reached too quickly, a lower value
should be set.
If the required temperature is reached too slowly, a higher value
should be set.
Change with +/–.
Conrm with OK.

14
6136715
Entering the date and time

15
6136715
Dening set temperatures
If you remain in one of these operating modes, the thermostat
is permanently set to this temperature range
(no programming).
6.1 Selecting the set comfort value

Turn the selector switch to
(configuration CF10).

Set the comfort temperature
(from 5
°C to max. comfort).

Confirm with OK.
6.2 Selecting the set
economy mode value

Turn the selector switch
to .

Select the setback temperature
(from 5
°C to 19 °C).

Confirm with OK.
6.3 Selecting the set frost
protection value

Turn the selector switch
to .

Set the frost protection
temperature (from 5
°C to 10 °C).

Confirm with OK.
1 3
5°C -> max. comfort
1 5 °C -> +19 °C
1
5 °C -> +10 °C
2
3
2
3
2

16
6136715
Dening set temperatures (continued)
6.4 Display features
When selecting the set values, depending on the thermostat
model and the selected set temperature, the screen colour may
change, or a set of
different colours may be shown.
Green up to 19 °C (low consumption)
Orange from 19.5 °C to 24°C (average consumption)
Red from 24.5 °C to max. comfort (high consumption)
Activate display illumination (CF05) to use this function,
depending on the thermostat model.
OR

17
6136715

18
6136715
Programming

19
6136715
Programming (continued)

20
6136715
Automatic mode
In AUTO mode, the thermostat is controlled
according to the day program.
The symbol
indicates a heat demand
(configuration CF16).
The automatic program can be temporarily
cancelled through:
-
"Party mode" – special enabling ( )
-
Absence mode ( )
-
Detection of open windows (symbol ), if this function
has been activated (configuration CF08). The heating then
switches to frost protection mode.
- Detection of absence (symbol
flashes),
if this function has been activated (configuration CF09).
The heating then switches to setback mode:
•Absence of 1.5 hours -> current set temperature -1.5 °C
•Absence of 3.5 hours -> current set temperature -3.5 °C
•Absence of 48 hours -> set frost protection temperature
: Heat demand
: Party mode
: Absence mode
: Measured temperature
: Outside temperature
: Open detection activated
: Presence is
detected
:External special enabling
: Battery spent
: Wireless transmission