ViewSonic VB-PEN-007 User manual

VB-PEN-007
Air Pen
User Guide
Model No. VS19566
P/N: VB-PEN-007
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in
a safe manner, as well as registering your product for future service. Warranty information contained in this User
Guide will describe your limited coverage from ViewSonic®Corporation, which is also found on our web site at
http://www.viewsonic.com in English, or in specific languages using the Regional selection box of our website.

2
Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding
the world’s expectations for technological evolution, innovation, and simplicity.
At ViewSonic®, we believe that our products have the potential to make a positive
impact in the world, and we are confident that the ViewSonic® product you have
chosen will serve you well.
Once again, thank you for choosing ViewSonic®!

3
Safety Precauons
Please read the following Safety Precautions before you start using the device.
• Keep this user guide in a safe place for later reference.
• Read all warnings and follow all instructions.
• Do not immerse the pen in water and store it in a cool, dry environment when
not in use.
• Avoid exposing the pen to direct sunlight or other continuous heat sources. Do
not place the pen in close proximity to heat sources such as: heat sinks, heaters,
or other sources of continuous heat.
• When charging this product, please use a dedicated charger/cord.
• This product contains a polymer lithium-ion battery. Do not attempt to
disassemble and replace the internal parts.
• Do not use this product alone with infants or children to avoid accidents.
• Do not put liquids near the pen. If liquid is spilled into or on the pen, it may
cause the pen to malfunction. If the pen becomes wet, please disconnect the
power and call your local service center to repair the pen.
• If the product emits an odor, becomes hot, discolored or deformed, or if
any abnormalities occur during use, storage or charging, discontinue use
immediately.
• If the battery leaks and the electrolyte gets into your eyes, please do not rub it,
use water to flush your eyes, and contact a medical professional immediately.
• Use only the accessories specified by the manufacturer.
• This product has no parts which can be repaired by the user. Any damage caused
by the user's own disassembly is not covered by warranty. Repair operations
should be performed by qualified professionals.

4
Contents
Safety Precautions....................................................... 3
Introduction ................................................................ 5
Package Contents ...................................................................................................5
Product Overview...................................................................................................6
Initial Setup................................................................. 7
Charging the VB-PEN-007 .......................................................................................7
Powering ON and Pairing the VB-PEN-007 .............................................................8
Re-Pairing the VB-PEN-007...................................................................................... 9
Using the VB-PEN-007 ............................................... 10
Pen Nibs................................................................................................................10
Replacing Pen Nibs ................................................................................................ 10
Using the Presentation Function ..........................................................................11
Appendix................................................................... 12
Presenter Pen Specifications ................................................................................12
USB Receiver Specifications..................................................................................12
LED Indicator Status..............................................................................................13
Regulatory and Service Information .......................... 14
Compliance Information.......................................................................................14
FCC Compliance Statement................................................................................... 14
FCC Radiation Exposure Statement....................................................................... 15
IC Warning Statement ........................................................................................... 15
CE Conformity for European Countries ................................................................. 16
Declaration of RoHS2 Compliance......................................................................... 17
Indian Restriction of Hazardous Substances ......................................................... 18
Product Disposal at End of Product Life ................................................................ 18
Copyright Information ..........................................................................................19
Customer Service .................................................................................................. 20

5
Introducon
Package Contents
Presenter Pen USB Receiver USB Cable
Fine Pen Nib Thick Pen Nib Conducve Pen Nib
Quick Start Guide
VB-PEN-007
PenTip
NextPage
LEDIndicator
AirMouse
PreviousPage
ĂƉĂĐŝƟǀĞWĞŶdŝƉ WŽǁĞƌƵƩŽŶ
Chargingport
ReceiverStorage
VolumeDown
&
VolumeUp
VB-PEN-007_QSG_1a_20230217
ŽƉLJƌŝŐŚƚΞϮϬϮϯsŝĞǁ^ŽŶŝĐŽƌƉŽƌĂƟŽŶůůƌŝŐŚƚƐƌĞƐĞƌǀĞĚ
www.viewsonic.comGet User Guide
FCC Compliance Statement
dŚŝƐĚĞǀŝĐĞĐŽŵƉůŝĞƐǁŝƚŚƉĂƌƚϭϱŽĨ&ZƵůĞƐKƉĞƌĂƟŽŶŝƐƐƵďũĞĐƚƚŽƚŚĞ
ĨŽůůŽǁŝŶŐƚǁŽĐŽŶĚŝƟŽŶƐ;ϭͿƚŚŝƐĚĞǀŝĐĞŵĂLJŶŽƚĐĂƵƐĞŚĂƌŵĨƵůŝŶƚĞƌĨĞƌĞŶĐĞ
ĂŶĚ;ϮͿƚŚŝƐĚĞǀŝĐĞŵƵƐƚĂĐĐĞƉƚĂŶLJŝŶƚĞƌĨĞƌĞŶĐĞƌĞĐĞŝǀĞĚŝŶĐůƵĚŝŶŐ
ŝŶƚĞƌĨĞƌĞŶĐĞƚŚĂƚŵĂLJĐĂƵƐĞƵŶĚĞƐŝƌĞĚŽƉĞƌĂƟŽŶ
Industry Canada Statement
E/^ͲϬϬϯ;ͿEDͲϬϬϯ;Ϳ
PresenterPen：s^ϭϵϱϲϲ;sͲWEͲϬϬϳͿ
&/'^^Ͳs^ϭϵϱϲϲ
//ϰϮϴϬͲs^ϭϵϱϲϲ
h^ZĞĐĞŝǀĞƌ s^ϭϵϱϲϳ;sͲWEͲϬϬϳͲϮͿ
&/'^^Ͳs^ϭϵϱϲϳ
//ϰϮϴϬͲs^ϭϵϱϲϳ
CE Conformity for European Countries
 dŚĞĚĞǀŝĐĞĐŽŵƉůŝĞƐǁŝƚŚƚŚĞDŝƌĞĐƟǀĞϮϬϭϰϯϬhĂŶĚ>Žǁ
 sŽůƚĂŐĞŝƌĞĐƟǀĞϮϬϭϰϯϱhĂŶĚZĂĚŝŽƋƵŝƉŵĞŶƚŝƌĞĐƟǀĞ 
 ;ZͿϮϬϭϰϱϯh
ŚƩƉƐǁǁǁǀŝĞǁƐŽŶŝĐŐůŽďĂůĐŽŵƉƵďůŝĐƉƌŽĚƵĐƚƐͺĚŽǁŶůŽĂĚƐĂĨĞ-
ƚLJͺĐŽŵƉůŝĂŶĐĞĂĐĐs^ϭϵϱϲϲͺͺKƉĚĨ
ŚƩƉƐǁǁǁǀŝĞǁƐŽŶŝĐŐůŽďĂůĐŽŵƉƵďůŝĐƉƌŽĚƵĐƚƐͺĚŽǁŶůŽĂĚƐĂĨĞ-
ƚLJͺĐŽŵƉůŝĂŶĐĞĂĐĐs^ϭϵϱϲϳͺͺKƉĚĨ
⇃垛‥⋩
䰈⠘䬭Ɲs^ϭϵϱϲϲ;sͲWEͲϬϬϳͿEŶƵŵďĞƌyyyyyyyyyyyyyy
86%㎌㔝♏s^ϭϵϱϲϳ;sͲWEͲϬϬϳͲϮͿEŶƵŵďĞƌyyyyyyyyyyyyyy
攎䏦䄧宨⋩㗇⾃㭿㣗䟸
ᾄ㪉樾㨀㹽&16Ḳ奶⮁⯮昷䔏䉐峑␒㛰ガ㲨㨀䤡㖣┭⒨Ḳ㜓檻˚
⋬壄˚㨀岣˚ㇽ媑㗵㛟˛昷䔏䉐峑␒㛰ガ㲨㨀䤡媲⎪俪󰶓⇾䶙✧
ŚƩƉƐǁǁǁǀŝĞǁƐŽŶŝĐŐůŽďĂůĐŽŵƉƵďůŝĐƉƌŽĚƵĐƚƐͺĚŽǁŶůŽĂĚƐĂĨĞ-
ƚLJͺĐŽŵƉůŝĂŶĐĞĂĐĐs^ϭϵϱϲϲͺͺKƉĚĨ
Quick Start Guide
NOTE: The package contents may vary by region.

6
Product Overview
Pen Nib
Next Page
LED Indicator
Air Mouse
Previous Page
Charging Port
Receiver Storage Power Buon
Pen Nib
Volume Down Volume Up

7
Inial Setup
Charging the VB-PEN-007
NOTE: Fully charge the VB-PEN-007 before its rst use.
USBUSB USB
USB Type C
1. Connect the USB Type C end of the included USB cable to the Charging Port of
the VB-PEN-007.
2. Then connect the other end, the USB Type A, of the cable to a USB Type A port of
a display or other power delivering device.
3. When charging, the LED Indicator will emit a constant red light. When fully
charged, the VB-PEN-007 can provide four (4) hours of use.
NOTE: A short, 10 minute charge can provide one (1) hour of use.

8
Powering ON and Pairing the VB-PEN-007
1. Plug the USB Receiver into a USB Type A port of a display device.
USBUSB USB
USB
2. Press and hold the VB-PEN-007’s Power Buon for three (3) seconds to begin
pairing.
NOTE: When in pairing mode, the LED Indicator will emit a blue ashing light.
USBUSB USB
USB
3. Aer successfully Powering ON and pairing the VB-PEN-007, the LED Indicator
will emit a constant blue light.

9
Re-Pairing the VB-PEN-007
If the VB-PEN-007 needs to be re-paired, please follow the steps below:
1. Remove the USB Receiver from the display device.
2. Press and hold both the Volume Up and Volume Down buons on the VB-
PEN-007 for three (3) seconds to enter pairing mode.
NOTE: When in pairing mode, the LED Indicator will emit a blue ashing light.
3. Plug the USB Receiver into a USB Type A port of the display device.
4. When paired successfully, the LED Indicator will emit a constant blue light.

10
Using the VB-PEN-007
Pen Nibs
The VB-PEN-007 is equipped with two (2) pen nibs.
Fine Nib Thick Nib
Pen nib for infrared (IR) screens. Conducve pen nib for infrared (IR)
and capacive screens.
NOTE: Aer 20 minutes of non-use, the pen will shut down and enter sleep
mode. Please press the Power Buon for three (3) seconds to re-enable
it.
Replacing Pen Nibs
When the pen nib develops a sharp or rough edge, it can be replaced with
replacement nibs. To replace a nib:
1. Rotate the pen nib holder counterclockwise and remove the old pen nib.
2. Insert the new pen nib and turn the pen nib holder clockwise to secure it.

11
Using the Presentaon Funcon
You can press and hold the Air Mouse buon to use the VB-PEN-007 as an on-
screen cursor, use the and buons as a previous page and next page switch,
and the side Volume Up and Down buons to control the volume level.
Pressing the Air Mouse buon and Power Buon at the same me will funcon as
a le mouse click buon.

12
Appendix
Presenter Pen Specicaons
Item Specicaons
Model No. VS19566
P/N VB-PEN-007
Wireless Connecon Type RF 2.4 GHz, 802.11b
Wireless Connecon Distance
30 m (98.43 )
Indicator Type
Air Mouse
Baery Type Li-ion Polymer Baery, ALP500950, 170mAh
Baery Life
50 days (Rechargeable)
Input Power Rang 5V/210mA, 1.05W
Antenna Type Chip Antenna
Automac Sleep Mode
20 minutes of inacvity
Operang Temperature
40° C (104° F)
Operang System Compability
Windows/Android/MacOS/Linux
Dimensions
153.5 x 18.7 x 18.3 mm
(6.04 x 0.74 x 0.72 in)
Weight
21 g (0.46 lb)
USB Receiver Specicaons
Item Specicaons
Model No. VS19567
P/N VB-PEN-007-2
Wireless Connecon Type RF 2.4 GHz, 802.11b
Wireless Connecon Distance
30 m (98.43 )
Supported USB USB 1.1 compable with USB 2.0 and 3.0
Input Power Rang
5V/16mA, 0.08W
Antenna Type PIFA
Dimensions
21.1 x 12.1 x 4.7 mm
(0.83 x 0.48 x 0.19 in)
Weight 1.5 g (0.003 lb)

13
LED Indicator Status
Indicator Light Descripon
Blue (Steady) Powered ON and paired
Blue (Flashing Quickly) Pairing in progress
Blue (Flashing Slowly) Low baery
Red (Steady) Charging

14
Regulatory and Service Informaon
Compliance Informaon
This secon addresses all connected requirements and statements regarding
regulaons. Conrmed corresponding applicaons shall refer to nameplate labels
and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operaon is subject to the following
two condions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operaon. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance
with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or television
recepon, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cauoned that changes or modicaons not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
Industry Canada Statement
CAN ICES-003(B) / NMB-003(B)
Presenter Pen: VS19566(VB-PEN-007)
FCC ID: GSS-VS19566
IC ID: 4280A-VS19566
USB Receiver: VS19567(VB-PEN-007-2)
FCC ID: GSS-VS19567
IC ID: 4280A-VS19567

15
FCC Radiaon Exposure Statement
This equipment complies with FCC radiaon exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 cm between the radiator & your body.
Validity of using the module cercaon:
In the event that these condions cannot be met (for example certain laptop
conguraons or co-locaon with another transmier), then the FCC authorizaon
for this module in combinaon with the host equipment is no longer considered
valid and the FCC ID of the module cannot be used on the nal product. In these
circumstances, the OEM integrator will be responsible for re-evaluang the end
product (including the transmier) and obtaining a separate FCC authorizaon.
Custom design antennas may be used, however the OEM installer must following
the FCC 15.21 requirements and verify if new FCC approval will be necessary.
IC Warning Statement
This device complies with Industry Canada license- exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitaon est autorisée aux deux condions
suivantes : ( 1 ) l’appareil ne doit pas produire de brouillage, et ( 2) l’ulisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage
est suscepble d’en compromere le fonconnement.

16
CE Conformity for European Countries
The device complies with the EMC Direcve 2014/30/EU, Low Voltage
Direcve 2014/35/EU and Radio Equipment Direcve 2014/53/EU.
hps://www.viewsonicglobal.com/public/products_download/safety_
compliance/acc/VS19566_CE_DoC.pdf
hps://www.viewsonicglobal.com/public/products_download/safety_
compliance/acc/VS19567_CE_DoC.pdf
The following informaon is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2012/19/EU (WEEE). The mark
indicates the requirement NOT to dispose of the equipment as unsorted
municipal waste, but use the return and collection systems according to
local law.

17
Declaraon of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direcve
2011/65/EU of the European Parliament and the Council on restricon of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Direcve) and is deemed to comply with the maximum concentraon values issued
by the European Technical Adaptaon Commiee (TAC) as shown below:
Substance Proposed Maximum
Concentraon
Actual
Concentraon
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6⁺) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Bis(2-ethylhexyl) phthalate (DEHP) 0.1% < 0.1%
Butyl benzyl phthalate (BBP) 0.1% < 0.1%
Dibutyl phthalate (DBP) 0.1% < 0.1%
Diisobutyl phthalate (DIBP) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex
III of the RoHS2 Direcves as noted below:
• Copper alloy containing up to 4% lead by weight.
• Lead in high melng temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
• Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.

18
Indian Restricon of Hazardous Substances
Restricon on Hazardous Substances statement (India). This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentraons exceeding 0.1 weight % and 0.01 weight % for cadmium, except for
the exempons set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is commied to working and living
green. Thank you for being part of Smarter, Greener Compung. Please visit the
ViewSonic® website to learn more.
USA & Canada:
hps://www.viewsonic.com/us/go-green-with-viewsonic
Europe:
hps://www.viewsonic.com/eu/go-green-with-viewsonic
Taiwan:
hps://recycle.epa.gov.tw/

19
Copyright Informaon
Copyright© ViewSonic® Corporaon, 2023. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microso, Windows, and the Windows logo are registered trademarks of Microso
Corporaon in the United States and other countries.
ViewSonic® and the three birds logo are registered trademarks of ViewSonic®
Corporaon.
VESA is a registered trademark of the Video Electronics Standards Associaon.
DPMS, DisplayPort, and DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protecon
Agency (EPA).
As an ENERGY STAR® partner, ViewSonic® Corporaon has determined that this
product meets the ENERGY STAR® guidelines for energy eciency.
Disclaimer: ViewSonic® Corporaon shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequenal damages
resulng from furnishing this material, or the performance or use of this product.
In the interest of connuing product improvement, ViewSonic® Corporaon
reserves the right to change product specicaons without noce. Informaon in
this document may change without noce.
No part of this document may be copied, reproduced, or transmied by any means,
for any purpose without prior wrien permission from ViewSonic® Corporaon.
VB-PEN-007_UG_ENG_1a_20231012

20
Customer Service
For technical support or product service, see the table below or contact your
reseller.
NOTE: You will need the product’s serial number.
Country/ Region Website Country/ Region Website
Asia Pacic & Africa
Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/
中国 (China) www.viewsonic.com.cn 香港 (繁體中文) www.viewsonic.com/hk/
Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/
Indonesia www.viewsonic.com/id/ Israel www.viewsonic.com/il/
日本 (Japan) www.viewsonic.com/jp/ Korea www.viewsonic.com/kr/
Malaysia www.viewsonic.com/my/ Middle East www.viewsonic.com/me/
Myanmar www.viewsonic.com/mm/ Nepal www.viewsonic.com/np/
New Zealand www.viewsonic.com/nz/ Pakistan www.viewsonic.com/pk/
Philippines www.viewsonic.com/ph/ Singapore www.viewsonic.com/sg/
臺灣 (Taiwan) www.viewsonic.com/tw/ ประเทศไทย www.viewsonic.com/th/
Việt Nam www.viewsonic.com/vn/ South Africa & Maurius www.viewsonic.com/za/
Americas
United States www.viewsonic.com/us Canada www.viewsonic.com/us
Lan America www.viewsonic.com/la
Europe
Europe www.viewsonic.com/eu/ France www.viewsonic.com/fr/
Deutschland www.viewsonic.com/de/ Қазақстан www.viewsonic.com/kz/
Россия www.viewsonic.com/ru/ España www.viewsonic.com/es/
Türkiye www.viewsonic.com/tr/ Україна www.viewsonic.com/ua/
United Kingdom www.viewsonic.com/uk/