ViewSonic SC-T47 User manual

SC-T47 (Win7 Pro)
Thin Client
User Guide
Model No. VS15835

i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment
Directive 2012/19/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any
spent or discarded batteries or accumulators as unsorted municipal waste, but
use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy
metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or
more than 0.004% Lead.

ii
Important Safety Instructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water. Warning: To reduce the risk of re or electric
shock, do not expose this apparatus to rain or moisture.
6. Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including ampliers) that produce heat.
8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the plug does not t into your outlet, consult an
electrician for replacement of the outlet.
9. Protect the power cord from being tread upon or pinched, particularly at the plug,
and the point where if emerges from the equipment. Be sure that the power outlet is
located near the equipment so that it is easily accessible.
10. Only use attachments/accessories specied by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the equipment. When a cart is used, use caution
when moving the cart/equipment combination to avoid injury from tipping over.
12. Unplug this equipment when it will be unused for long periods of time.
13. Refer all servicing to qualied service personnel. Service is required when the unit
has been damaged in any way, such as: if the power-supply cord or plug is damaged,
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or
moisture, or if the unit does not operate normally or has been dropped.
14. Do not remove equipment covers and access any of the components inside the
equipment. Any access inside the equipment without an authorized or certied
technician may cause serious injuries and damage. For any problem, contact your
dealer for assistance.
15. Don’t use a keyboard and mouse that in total require more than 200 mA of rated
current during operation.
16. Use only power supplies listed in the user instructions.

iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/
EU of the European Parliament and the Council on restriction of the use of certain
hazardous substances in electrical and electronic equipment (RoHS2 Directive) and
is deemed to comply with the maximum concentration values issued by the European
Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III of the
RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent lamps
(CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other than
dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic
matrix compound.

iv
Copyright Information
Copyright © ViewSonic Corporation, 2015. All rights reserved.
ViewSonic, the three birds logo, and MultiClient are either registered trademarks or
trademarks of ViewSonic Corporation.
Microsoft®, Windows®, and MultiPoint™ are trademarks of the Microsoft group of
companies.
ENERGY STAR®is a registered trademark of the U.S. Environmental Protection
Agency (EPA). As an ENERGY STAR®partner, ViewSonic Corporation has
determined that this product meets the ENERGY STAR®guidelines for energy
efciency.
Other product names mentioned herein are used for identication purposes only and may
be trademarks and/or registered trademarks of their respective companies.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the
right to change product specications without notice. Information in this document may
change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
NOTE
• Display Off Mode
Within 15 minutes of user inactivity, the display will be turned off to reduce
power consumption by the factory default. The display returns to the Display
Normal mode upon sensing a request from a user such as moving the mouse
or pressing a key.
(To adjust the setting, log in to the system with an administrative account,
click Start > Control Panel > System and Security > Power Options >
Choose when to turn off the display, select a desired option through the
drop-down menu, and then click Save Changes to apply.)
• System Sleep Mode
To switch to the System Sleep mode for your SC-T45, please do the following:
1. Press Alt + F4 on the keyboard.
2. On the appeared window, click the drop-down menu to select Sleep.
(To return to the Normal mode, press the Power button. You may need to
provide user credentials.)
NOTE
• The default power management settings have been selected for compliance
with ENERGY STAR that are recommended by the ENERGY STAR program
for optimal energy savings.

v
Product Registration
To meet your future needs, and to receive any additional product information as it
becomes available, please register your product on the Internet at: www.viewsonic.com.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
SC-T47
ViewSonic Thin Client
VS15835
SC-T47_UG_ENG Rev. 1B 09-03-15
_______________________________
_______________________________
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank
you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn
more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Table of Contents
Compliance Information i
Important Safety Instructions ii
Declaration of RoHS2 Compliance iii
Copyright Information iv
Product Registration v
1 Overview 1
1.1 Package Contents 2
1.2 Exterior Views 3
1.3 Panel Components 3
1.4 LED Indicators 6
2 Setting Up Your SC-T47 7
2.1 Positioning Your SC-T47 8
2.2 Getting Connected 11
Specications 12
Customer Support 13
Limited Warranty 14

1
Overview
1
This chapter provides an overview of your SC-T47 thin clients.
1.1 Package Contents
Check your package contents 2
1.2 Exterior Views
Overview of thin client outside elements 3
1.3 Panel Components
Descriptions of front and rear panel components 3
1.4 LED Indicators
Descriptions of signals for LED indicators 6

Overview
Package Contents
2
1.1 Package Contents
Please check your package contents. Ensure that all of the items are present in your package. If any items are
missing or damaged, please contact your dealer immediately.
ViewSonic SC-T47 AC adapter
Detachable AC cord
Quick Start Guide Stand Optical Disk
Thin Client
05/05/14 Thin Client_DVD Made in Taiwan
Compliance Information
brochure VESA Mount Plate Screw M3XL10*1
DVI-I to VGA Adapter

Overview
Exterior Views
3
1.2 Exterior Views
1.3 Panel Components
Front/Bottom View
Stand Lock Slot
Front Panel
Pad/VESA Holes
Left Rear View
Kensington
Security Slot
Rear Panel
I/O interface (See next section
for details)

Overview
Panel Components
4
1
2
3
4
5
6
7
Front Panel Components
No. Sign Name Description
1 Power LED Indicates the status of power.
2 Power button Press to turn on your SC-T47.
3 SSD LED Indicates the status of SSD (Solid-State Drive).
4Headphone port Connects to a set of headphones or a speaker system.
5Microphone port Connects to a microphone.
6USB port (USB 3.0) Connects to a USB device.
7USB port (USB 2.0) Connects to a USB device.

Overview
Panel Components
5
Rear Panel Components
No. Sign Name Description
1DVI-I port Connects to a monitor.
2Serial port
(RS-232) Connects to a serial port device such as a printer or a point-of-sale device.
3DVI-I port Connects to a monitor.
4Kensington
security slot Attaches to a permanent object with a security cable.
5DVI-I port Connects to a monitor.
6LAN port Connects to a computer network.
7DVI-D port Connects to a monitor.
8USB port
(USB 2.0) Connects to a USB device.
9DC IN Connects to an AC adapter.
7
3
4
5
6
8
2
1
9
Selectable Rear I/O Modules
Serial and Extra DVI Ports:
1
2
5

Overview
LED Indicators
6
1.4 LED Indicators
Your SC-T47 is equipped with LED indicators for the states of power and solid-state drive. The meanings of LED
signals are described as follows:
LED Signal Meaning
Power LED Blue Your SC-T47 is in Power-on mode.
Orange Your SC-T47 is in Standby mode.
SSD LED Orange blinking The SSD (Solid-State Drive) is in use.
The LAN port of your SC-T47 is equipped with LED indicators for the networking states. The meanings of LED signals
are described as follows:
Left LED
(transmission rate)
Right LED
(transmission activity)
Meaning
LED Signal
Off Off Your SC-T47 is not connected to a LAN.
Off Amber blinking Your SC-T47 connects to a 10 Mbps LAN.
Orange Amber blinking Your SC-T47 connects to a 100 Mbps LAN.
Green Amber blinking Your SC-T47 connects to a 1000 Mbps LAN.

7
This chapter gives detailed instructions on how to set up and
get your SC-T47 ready for use.
2.1 Positioning Your SC-T47
8
2.2 Getting Connected
11
Setting Up Your SC-T47
2

Setting Up Your SC-T47
Positioning Your SC-T47
8
2.1 Positioning Your SC-T47
Three placement options are available for your SC-T47: horizontal, upright, or VESA-mounted. You can choose one
which suits your needs best.
Horizontal placement
To position your SC-T47 horizontally, please follow the steps below:
1. Attach the included four (4) rubber pads to the four (4) pad holes on the underside of your SC-T47.
2. Ensure that the desired place has a level surface.
3. Place your SC-T47 on the desired position.
Upright placement
To position your SC-T47 uprightly, please follow the steps below:
1. Hold the front panel of your SC-T47 in one hand with the lock slot side facing upward.

Setting Up Your SC-T47
Positioning Your SC-T47
9
2. Hold the stand of your SC-T47 in the other hand with the underside facing upward and the side marked with
a word FRONT facing left.
3. Align the stand with the lock slot side of your SC-T47, put four (4) hooks of the stand into the lock slots, and
then slide the stand left to lock it into place.
4. Secure the stand to your SC-T47 with one (1) screws supplied.
5. Place your SC-T47 uprightly with its xed stand on the desired position.

Setting Up Your SC-T47
Positioning Your SC-T47
10
VESA-mounted
To mount your SC-T47, please follow the steps below:
1. Ensure that all rubber pads on the underside of your SC-T47 are removed from the pad holes and the pad /
VESA holes are clean without any blockage.
2. Align two mount holes on the VESA bracket with two mount holes on your SC-T47, and then secure the
bracket to your SC-T47 with two (2) screws as shown below.
3. Align the mount holes on the VESA bracket with the mount holes on the monitor, and then secure the
bracket and SC-T47 to the monitor with two (2) screws as shown. Ensure that your SC-T47 is located in the
center of the monitor and the rear panel of your SC-T47 is facing rightward as shown below.

Setting Up Your SC-T47
Getting Connected
11
2.2 Getting Connected
To make connections for your SC-T47, please do the following:
1. Connect the monitor(s) to the DVI-D / DVI-I port.
2. Connect a keyboard and mouse to your SC-T47 through the USB ports.
3. Connect your SC-T47 to a LAN through the LAN port or SFP port (if any).
4. Plug the detachable AC cord into the AC adapter.
5. Connect the AC plug of the adapter to a power outlet and the DC plug of the adapter to your SC-T47.

12
Specications
ViewSonic SC-T47 thin client
Processor Intel® Baytrail Quad-core J1900, 2.0 GHz
Chipset Intel®HD graphics chip and SMSC UFX6000
Memory 4 GB
Solid-State
Drive
32 GB
Resolutions Up to 1920 x 1200
I/O Interfaces Front Panel
2 x USB 2.0
1 x USB 3.0
1 x Microphone
1 x Headphone
Rear Panel
2 x USB 2.0
1 x RJ-45
3 x DVI-I
1 x DVI-D
1 x DC IN
1 x Serial (RS-232)
Networking 10/100/1000Mb Ethernet
Wireless IEEE 802.11 b/g/n
Power Input/Output: 100-240Vac, 1A, 50-60 Hz / DC +12Vdc, 3A
Operating
system
Windows 7 Pro
Security Kensington lock slot
Dimensions (W)179 x (H)197.2 x (D)44 mm
Net Weight 1.13 kg
Environment Operating Temperature: 0° C ~ 35° C (upright)
Operating Temperature: 0° C ~ 35° C (monitor-mounted)
Operating Temperature: 0° C ~ 35° C (horizontal)
Non-operating Temperature: - 30° C ~ 60° C
Operating Humidity (Rh): 10% ~ 90% (non-condensing)
Non-operating Humidity (Rh): 5% ~ 95%

13
Other Information
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/
Region Website T= Telephone C = CHAT ONLINE Email
Australia/New
Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 [email protected]
Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533 [email protected]
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [email protected]
India www.in.viewsonic.com T= 1800 266 0101 [email protected]
Korea ap.viewsonic.com/kr/ T= 080 333 2131 [email protected]
Latin America
(Argentina) www.viewsonic.com/la/ C= http://www.viewsonic.com/la/ soporte/servicio-tecnico [email protected]
Latin America
(Chile) www.viewsonic.com/la/ C= http://www.viewsonic.com/la/ soporte/servicio-tecnico [email protected]
Latin America
(Columbia) www.viewsonic.com/la/ C= http://www.viewsonic.com/la/ soporte/servicio-tecnico [email protected]
Latin America
(Mexico) www.viewsonic.com/la/ C= http://www.viewsonic.com/la/ soporte/servicio-tecnico [email protected]
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: [phone])6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America
(Peru) www.viewsonic.com/la/ C= http://www.viewsonic.com/la/ soporte/servicio-tecnico [email protected]
Macau www.hk.viewsonic.com T= 853 2870 0303 [email protected]
Middle East ap.viewsonic.com/me/ Contact your reseller [email protected]
Puerto Rico &
Virgin Islands www.viewsonic.com
T= 1-800-688-6688 (English)
C = http://www.viewsonic.com/
la/soporte/servicio-tecnico
[email protected]
[email protected]
Singapore/
Malaysia/
Thailand
www.ap.viewsonic.com T= 65 6461 6044 [email protected]
South Africa ap.viewsonic.com/za/ Contact your reseller [email protected]
United States www.viewsonic.com T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530 [email protected]