ViewSonic LS610WHE User manual

LS610WHE
LS610HDHE
Projector
User Guide
Model No. VS19173 | VS19174
Model Name: LS610WHE | LS610HDHE
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in
a safe manner, as well as registering your product for future service. Warranty information contained in this User
Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at
http://www.viewsonic.com in English, or in specific languages using the Regional selection box of our website.

2
Contents
Introduction ................................................................ 5
Product Overview...................................................................................................6
Projector.................................................................................................................. 6
Controls and Functions ................................................................................................. 6
Connection Ports........................................................................................................... 7
Remote Control....................................................................................................... 8
Controls and Functions ................................................................................................. 8
Remote Control Effective Range................................................................................... 9
Replacing the Remote Control Batteries....................................................................... 9
Initial Setup............................................................... 10
Choosing a Location..............................................................................................10
Projection Dimensions..........................................................................................11
LS610WHE ............................................................................................................. 11
16:10 Image on a 16:10 Screen................................................................................... 11
16:10 Image on a 4:3 Screen....................................................................................... 12
LS610HDHE............................................................................................................ 13
16:9 Image on a 16:9 Screen....................................................................................... 13
16:9 Image on a 4:3 Screen......................................................................................... 14
Mounting the Projector........................................................................................15
Preventing Unauthorized Use...............................................................................16
Using the Security Slot .......................................................................................... 16
Using the Password Function ................................................................................ 17
Setting a Password...................................................................................................... 17
Changing the Password............................................................................................... 18
Disabling the Password Function ................................................................................ 18
Forgetting the Password ............................................................................................. 19
Password Recall Procedure......................................................................................... 19
Locking the Control Keys ....................................................................................... 19

3
Making Connections.................................................. 20
Connecting to Power ............................................................................................20
Connecting to Video/Computer Sources..............................................................21
HDMI Connection.................................................................................................. 21
Connecting to Audio.............................................................................................21
Operation.................................................................. 22
Turning the Projector ON/OFF..............................................................................22
Starting Up the Projector ...................................................................................... 22
First Time Activation ................................................................................................... 22
Shutting Down the Projector................................................................................. 23
Selecting an Input Source .....................................................................................24
Adjusting the Projected Image .............................................................................25
Adjusting the Projector's Height and Projection Angle............................................... 25
Fine-Tuning the Image Size and Clarity ................................................................. 25
Correcting Keystone.............................................................................................. 26
Hiding the Image ..................................................................................................27
Controlling the Projector through a LAN Environment ........................................28
Configuring the LAN Control Settings.................................................................... 28
Menu Functions ........................................................ 30
General On-Screen Display (OSD) Menu Operation .............................................30
On-Screen Display (OSD) Menu Tree....................................................................31
DISPLAY Menu ......................................................................................................36
IMAGE Menu ........................................................................................................39
POWER MANAGEMENT Menu .............................................................................42
BASIC Menu ..........................................................................................................45
ADVANCED Menu .................................................................................................48
SYSTEM Menu.......................................................................................................52
INFORMATION Menu ...........................................................................................54

4
Appendix................................................................... 55
Specifications........................................................................................................55
Projector Dimensions............................................................................................ 56
Timing Chart .........................................................................................................56
Troubleshooting ...................................................................................................58
Common Problems................................................................................................ 58
LED Indicators........................................................................................................ 59
Light Source Information......................................................................................60
Light Source Hour.................................................................................................. 60
Extending Light Source Life ................................................................................... 60

5
Package Contents
Projector Remote Control &
Batteries
Power Cord Quick Start Guide
NOTE: The power cord included in your package may vary depending on your country.
Please contact your local reseller for more informaon.
Introduction

6
Product Overview
Projector
Controls and Functions
MENU
EXIT
SOURCE
?
ENTER
BLANK
COLOR
MODE
Power Indicator Light
Temperature Indicator Light
Light Source Indicator Light
Projection Lens
Remote IR sensor
Power key
Remote IR sensor
Focus Ring
Zoom Ring
Key Description
[ ] Power Toggles the projector between standby mode and Power
On.
[/ / / ] Keystone
Keys
Manually corrects distorted images resulting from an
angled projection.
[/ / / ]
Left/Right/Up/Down
Selects the desired menu items and makes adjustments
when the On-Screen Display (OSD) Menu is activated.
Menu/Exit Turns on or off the On-Screen Display (OSD) Menu.
Source Displays the input source selection bar.
(Help) Displays the HELP menu.
Blank Hides the screen picture.
Enter Enacts the selected On-Screen Display (OSD) Menu item
when the OSD Menu is activated.
[] Corner Adjustment Displays the Corner Adj. menu when the OSD menu is not
activated.
Color Mode Displays the color mode selection bar.

77
Connection Ports
LS610HDHE
LS610WHE
AUDIO OUTAUDIO IN RS232
AUDIO OUTAUDIO IN RS232
1235 6 7
4
AC Power Cord Inlet
Ceiling Mount Holes
Security Slot
Security Bar
Adjuster Foot
Port Description
[1] CONTROL LAN port.
[2] AUDIO OUT Audio signal output socket.
[3] AUDIO IN Audio signal input socket.
[4] HDMI 1 HDMI port.
[5] HDMI 2 HDMI port.
[6] USB 5V/1.5A OUT (Service) USB Type A port for power supply and serivce.
[7] RS232 RS232 control port.

8
Remote Control
Controls and Functions
Button Description
On/ Off Toggles between standby
mode and Power On.
COMP No function.
HDMI 1 Selects the source from the
HDMI 1 port for display.
HDMI 2 Selects the source from the
HDMI 2 port for display.
Auto Sync No function.
Source Displays the source selection
bar.
[ / / / ]
Keystone Keys
Manually corrects distorted
images resulting from an
angled projection.
Enter Enacts the selected OSD
Menu item.
(Corner
adjustment)
Displays the Corner Adj.
menu when the OSD menu is
not activated.
Left/ Right
Up/ Down
Selects the desired menu
items and makes adjustments.
Button Description
Menu
Turns on/off the On-Screen
Display (OSD) Menu or goes
back to previous OSD Menu.
(Laser)
Emits visible laser pointer light
for presentation purposes.
Exit Exits and saves menu
settings.
Aspect Displays the aspect ratio
selection bar.
Freeze Freezes the projected image.
Pattern Displays embedded test
pattern.
Blank Hides the screen picture.
PgUp (Page Up)/
PgDn (Page
Down)
Operates your display
software program (on
a connected PC) which
responds to page up/down
commands (like Microsoft
PowerPoint).
NOTE: Only available when
a PC input signal is
selected.
(Presentation
Timer)
Displays the
Presentation Timer menu.
Eco Mode Selects the Eco mode.
(Volume Up) Increases the volume level.
(Volume
Down) Decreases the volume level.
(Mute) Toggles audio between on
and off.
Color Mode Displays the color mode
selection bar.
Magnifies the projected
picture size.
Reduces the projected
picture size.
(INFORMATION)
Displays the INFORMATION
menu.
Network Displays the
LAN Control Settings menu.

9
Remote Control Effective Range
To ensure proper function of the remote control
follow the steps below:
1. The remote control must be held at an angle
within 30° perpendicular to the projector’s IR
remote control sensor(s).
2. The distance between the remote control and
the sensor(s) should not exceed 8 m (26 ft.)
NOTE: Refer to the illustration for the location of
the infrared (IR) remote control sensor(s).
Approx. 30°
Approx. 30°
Replacing the Remote Control Batteries
1. Remove the battery cover from the rear of the remote control by pressing the
finger grip and sliding it down.
2. Remove any existing batteries (if necessary) and install two AAA batteries.
NOTE: Observe the battery’s polarities as indicated.
3. Replace the battery cover by aligning it with the base and pushing it back into
position.
NOTE:
• Avoid leaving the remote control and batteries in excessive heat or a humid
environment.
• Replace only with the same or equivalent type recommended by the battery
manufacturer.
• Dispose of the used batteries according to the manufacturer’s instructions and
local environment regulations for your region.
• If the batteries are drained or if you will not be using the remote control for an
extended period of time, remove the batteries to avoid damage to the remote
control.

10
Initial Setup
This section provides detailed instructions for setting up your projector.
Choosing a Location
Personal preference and room layout will decide the installation location. Consider
the following:
• Size and Position of your screen.
• Location of a suitable power outlet.
• Location and Distance between the projector and other equipment.
The projector is designed to be installed in one of the following locations:
1. Front
The projector is placed near the floor in
front of the screen.
2. Front Ceiling
The projector is suspeneded upside-
down from the ceiling in front of the
screen.
3. Rear Ceiling
The projector is suspended upside-down
from the ceiling behind the screen.
NOTE: A special rear projection screen
is required.
4. Rear
The projector is placed near the floor
behind the screen.
NOTE: A special rear projection screen
is required.

11
Projection Dimensions
NOTE: See “Specifications” on page 55 for the native display resolution of this
projector.
LS610WHE
• 16:10 Image on a 16:10 Screen
• 16:10 Image on a 4:3 Screen
(a)
(c)
(b)
(e)
(f)
(d)
NOTE: (e) = Screen
(f) = Center of Lens
16:10 Image on a 16:10 Screen
(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset
minimum maximum maximum
in. mm in. mm in. mm in. mm in. mm
30 762 34.75 883 41.71 1059 15.90 404 -1.67 -42
40 1016 46.34 1177 55.61 1412 21.20 538 -2.23 -57
50 1270 57.92 1471 69.51 1766 26.50 673 -2.78 -71
60 1524 69.51 1766 83.41 2119 31.80 808 -3.34 -85
70 1778 81.09 2060 97.31 2472 37.10 942 -3.90 -99
80 2032 92.68 2354 111.21 2825 42.40 1077 -4.45 -113
90 2286 104.26 2648 125.12 3178 47.70 1212 -5.01 -127
100 2540 115.85 2943 139.02 3531 53.00 1346 -5.56 -141
120 3048 139.02 3531 166.82 4237 63.60 1615 -6.68 -170
150 3810 173.77 4414 208.53 5297 79.50 2019 -8.35 -212
200 5080 231.70 5885 278.03 7062 106.00 2692 -11.13 -283
250 6350 289.62 7356 347.54 8828 132.50 3365 -13.91 -353
300 7620 347.54 8828 417.05 10593 159.00 4039 -16.69 -424

12
16:10 Image on a 4:3 Screen
(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset
minimum maximum maximum
in. mm in. mm in. mm in. mm in. mm
30 762 32.79 833 39.34 999 15.00 381 -1.58 -40
40 1016 43.72 1110 52.46 1332 20.00 508 -2.10 -53
50 1270 54.65 1388 65.57 1666 25.00 635 -2.63 -67
60 1524 65.57 1666 78.69 1999 30.00 762 -3.15 -80
70 1778 76.50 1943 91.80 2332 35.00 889 -3.68 -93
80 2032 87.43 2221 104.92 2665 40.00 1016 -4.20 -107
90 2286 98.36 2498 118.03 2998 45.00 1143 -4.73 -120
100 2540 109.29 2776 131.15 3331 50.00 1270 -5.25 -133
120 3048 131.15 3331 157.38 3997 60.00 1524 -6.30 -160
150 3810 163.94 4164 196.72 4997 75.00 1905 -7.88 -200
200 5080 218.58 5552 262.30 6662 100.00 2540 -10.50 -267
250 6350 273.23 6940 327.87 8328 125.00 3175 -13.13 -333
300 7620 327.87 8328 393.45 9994 150.00 3810 -15.75 -400
NOTE: It is recommended that if you intend to permanently install the projector,
please physically test the projection size and distance using the actual
projector in situ before you permanently install it.

13
LS610HDHE
• 16:9 Image on a 16:9 Screen
(a)
(d)
(c)
(b)
(e)
(f)
(a)
(c)
(b)
(e)
(f)
(d)
• 16:9 Image on a 4:3 Screen
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
NOTE: (e) = Screen
(f) = Center of Lens
16:9 Image on a 16:9 Screen
(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset
minimum maximum maximum
in. mm in. mm in. mm in. mm in. mm
30 762 34.07 865 40.88 1038 14.71 374 -1.25 -32
40 1016 45.42 1154 54.50 1384 19.61 498 -1.67 -42
50 1270 56.78 1442 68.13 1731 24.51 623 -2.08 -53
60 1524 68.13 1731 81.76 2077 29.42 747 -2.50 -64
70 1778 79.49 2019 95.38 2423 34.32 872 -2.92 -74
80 2032 90.84 2307 109.01 2769 39.22 996 -3.33 -85
90 2286 102.20 2596 122.64 3115 44.12 1121 -3.75 -95
100 2540 113.55 2884 136.26 3461 49.03 1245 -4.17 -106
120 3048 136.26 3461 163.51 4153 58.83 1494 -5.00 -127
150 3810 170.33 4326 204.39 5192 73.54 1868 -6.25 -159
200 5080 227.10 5768 272.52 6922 98.05 2491 -8.33 -212
250 6350 283.88 7211 340.65 8653 122.57 3113 -10.42 -265
300 7620 340.65 8653 408.79 10383 147.08 3736 -12.50 -318

14
16:9 Image on a 4:3 Screen
(a) Screen Size (b) Projection Distance (c) Image Height (d) Vertical Offset
minimum maximum maximum
in. mm in. mm in. mm in. mm in. mm
30 762 31.27 794 37.52 953 13.50 343 -1.15 -29
40 1016 41.69 1059 50.03 1271 18.00 457 -1.53 -39
50 1270 52.11 1324 62.54 1588 22.50 572 -1.91 -49
60 1524 62.54 1588 75.04 1906 27.00 686 -2.30 -58
70 1778 72.96 1853 87.55 2224 31.50 800 -2.68 -68
80 2032 83.38 2118 100.06 2541 36.00 914 -3.06 -78
90 2286 93.80 2383 112.56 2859 40.50 1029 -3.44 -87
100 2540 104.23 2647 125.07 3177 45.00 1143 -3.83 -97
120 3048 125.07 3177 150.09 3812 54.00 1372 -4.59 -117
150 3810 156.34 3971 187.61 4765 67.50 1715 -5.74 -146
200 5080 208.45 5295 250.14 6354 90.00 2286 -7.65 -194
250 6350 260.57 6618 312.68 7942 112.50 2858 -9.56 -243
300 7620 312.68 7942 375.22 9530 135.00 3429 -11.48 -291
NOTE: It is recommended that if you intend to permanently install the projector,
please physically test the projection size and distance using the actual
projector in situ before you permanently install it.

1515
Mounting the Projector
NOTE: If you buy a third-party mount, please use the correct screw size. Screw size
can vary depending on the thickness of the mounting plate.
1. To ensure the most secure installation, please use a ViewSonic® wall or ceiling
mount.
2. Ensure the screws used to attach a mount to the projector meet the following
specifications:
• Screw type: M4
• Screw length: 12.8 mm ~ 15.8 mm
145.6
176.6
282.9
305.9
NOTE:
• Avoid installing the projector near a heat source.
• Keep at least a 10 cm gap between the ceiling and the bottom of the projector.

16
Preventing Unauthorized Use
The projector has several built-in security features to prevent theft, access, or
accidental setting changes.
Using the Security Slot
To help prevent the projector from being stolen, use a security slot locking device
to secure the projector to a fixed object.
Below is an example of setting up a security slot locking device:
NOTE: The security slot can also be used as a safety anchor if the projector is
mounted to the ceiling.

1717
Using the Password Function
To help prevent unauthorized access or use, the projector offers a password
security option. The password can be set through the On-Screen Display (OSD)
Menu.
NOTE: Make note of your password, and keep it in a safe place.
Setting a Password
1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings and
press Enter.
2. Highlight Power On Lock and select
On by pressing / .
3. As pictured to the right, the four
arrow keys ( , , , ) represent
4 digits (1, 2, 3, 4). Press the arrow
keys to enter a six digit password.
4. Confirm the new password by re-entering the new password. Once the password
is set, the OSD Menu will return to the Security Settings page.
5. Press Exit to leave the OSD Menu.
NOTE: Once set, the correct password must be entered every time the projector is
started.

18
Changing the Password
1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >
Change Password.
2. Press Enter, the message, ‘INPUT CURRENT PASSWORD’ will appear.
3. Enter the old password.
If the password is correct, the message, ‘INPUT NEW PASSWORD’ will
appear.
If the password is incorrect, a password error message will appear for 5
seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can
try again or press Exit to cancel.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. To leave the OSD Menu, press Exit.
NOTE: The digits being input will display as asterisks (*).
Disabling the Password Function
1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings >
Power On Lock.
2. Press / to select Off.
3. The message, “Input Password” will appear. Enter the current password.
If the password is correct, the OSD Menu returns to the Password page with
“Off” shown in the row of Power On Lock.
If the password is incorrect, a password error message will appear for 5
seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can
try again or press Exit to cancel.
NOTE: Please keep the old password, as you will need it to reactivate the password
function.

19
Forgetting the Password
If the password function is activated, you will
be asked to enter the six-digit password every
time you turn on the projector. If you enter the
wrong password, the password error message,
as pictured to the right, will appear for 5
seconds, and the message ‘INPUT PASSWORD’
follows.
You can retry or if you do not remember, you can use the “Password Recall
Procedure”.
NOTE: If you enter an incorrect password 5 times in succession, the projector will
automatically shut down for a short time.
Password Recall Procedure
1. When the message ‘INPUT CURRENT
PASSWORD’ appears, press and hold
Auto Sync for 3 seconds. The projector will
display a coded number on the screen.
2. Write down the number and turn off your
projector.
3. Seek help from the local service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the
projector.
Locking the Control Keys
With the control keys on the projector locked, you can prevent your settings from
being changed accidentally (by children, for example).
NOTE: When the Panel Key Lock is On, no control keys on the projector will operate
except Power.
1. Press Menu to open the OSD Menu and go to: SYSTEM > Panel Key Lock.
2. Press /to select On.
3. Select Yes and press Enter to confirm.
4. To release panel key lock, press and hold on the projector for 3 seconds.
NOTE: You can also use the remote control to enter the SYSTEM > Panel Key Lock
menu and select Off.

20
Making Connections
This section guides you on how to connect the projector with other equipment.
Connecting to Power
1. Connect the power cord to the AC IN jack at the rear of the projector.
2. Plug the power cord into a power outlet.
NOTE: When installing the projector, incorporate a readily accessible disconnect
device in the xed wiring, or connect the power plug to an easily accessible
outlet near the unit. If a fault should occur during operaon of the projector,
use the disconnect device to switch o the power supply, or disconnect the
power plug.