ViewSonic PJL7211 User manual

- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
- Руководство пользователя
- 使用手冊 (繁體)
- 使用手冊 (簡體)
- 사용자 안내서
Model No. : VS12890
ViewSonic®
PJL7211
XGA LCD Projector

PJL7211ViewSonic i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
For Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent
or discarded batteries or accumulators as unsorted municipal waste, but use the return
and collection systems available.
If the batteries, accumulators and button cells included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of
more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
This is a Class A product in European Union.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

PJL7211ViewSonic ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in this guide for
further instructions.
7.
Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade and the third prong are provided for your safety. If
the provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience
receptacles and the point where they exit from the unit. Be sure that the power outlet is
located near the unit so that it is easily accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the unit. When a cart is used, use caution when
moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the unit has
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is
spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the
unit does not operate normally or has been dropped.

PJL7211ViewSonic iii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of
the European Parliament and the Council on restriction of the use of certain hazardous substances
in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the
maximum concentration values issued by the European Technical Adaptation Committee (TAC)
as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex of the RoHS
Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other lamps not
specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and electronic
ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.

PJL7211ViewSonic iv
Copyright Information
Copyright©ViewSonic©Corporation, 2009. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks
of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC
are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from furnishing
this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®
Wizard CD-ROM also provides an opportunity for you to print the registration form, which you
may mail or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJL7211
ViewSonic XGA LCD Projector
VS12890
PJL7211_UG_ENG Rev. 1A 08-18-09
_______________________________
_______________________________
Personal Identication Number (PIN):
The lamp in this product contains mercury.
Please dispose of in accordance with local, state or federal laws.

PJL7211ViewSonic 1
Projector
PJL7211
User’s Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read “Safety Guide” rst. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
• Mac® is a registered trademark of Apple Inc.
• Windows® is a registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.

PJL7211ViewSonic 2
Contents
Contents
About this manual. . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . . 2
Projector features. . . . . . . . . . . 3
Preparations . . . . . . . . . . . . . . . 3
Checking the contents of package . . . 3
Part names . . . . . . . . . . . . . . . . 4
Projector ......................4
Control panel ...................5
Rear panel ....................5
Remote control . . . . . . . . . . . . . . . . . 6
Setting up . . . . . . . . . . . . . . . . . 7
Arrangement ...................7
Connecting your devices . . . . . . . . . . 9
Connecting power supply . . . . . . . . 11
Using the security bar and slot . . . . 11
Remote control . . . . . . . . . . . . 12
Installing the batteries . . . . . . . . . . . 12
About the remote control signal . . . 13
Changing the frequency of remote control signal . . 13
Power on/off . . . . . . . . . . . . . . 14
Turning on the power . . . . . . . . . . . 14
Turning off the power . . . . . . . . . . . 14
Operating . . . . . . . . . . . . . . . . 15
Selecting an input signal . . . . . . . . . 15
Searching an input signal . . . . . . . . 16
Selecting an aspect ratio . . . . . . . . . 16
Adjusting the projector’s elevator . . 17
Adjusting the zoom and focus . . . . . 17
Using the automatic adjustment feature . . . 18
Adjusting the position . . . . . . . . . . . 18
Correcting the keystone distortions . . 19
Using the magnify feature . . . . . . . . 19
Temporarily freezing the screen . . . 20
Temporarily blanking the screen . . 20
Using the menu function . . . . . . . . 21
EASY MENU. . . . . . . . . . . . . . . 23
Aspect, Keystone, picture mode,
eco mode, mirror, reset, Filter time,
lAnguAge, AdvAnced menu, exit
PICTURE menu . . . . . . . . . . . . 25
Brightness, contrAst, gAmmA,
color temp, color, tint, shArpness,
mymemory
IMAGE menu . . . . . . . . . . . . . . 28
Aspect, over scAn, v position, h position,
h phAse, h size, Auto Adjust execute
INPUT menu . . . . . . . . . . . . . . 30
progressive, video nr, color spAce,
video FormAt, computer in, FrAme locK,
resolution
SETUP menu . . . . . . . . . . . . . . 33
Keystone, eco mode, mirror
SCREEN menu. . . . . . . . . . . . . 34
lAnguAge, menu position, BlAnK,
stArt up,
MyScreen, MyScreen Lock
,
messAge, source nAme, templAte, c.c.
OPTION menu . . . . . . . . . . . . . 39
Auto seArch, direct on,
Auto oFF, lAmp time, Filter time,
myButton, mysource, service
SECURITY menu . . . . . . . . . . . 44
security pAssword chAnge,
MyScreen
pAssword, pin locK,
mytext pAssword, mytext displAy,
mytext writing
Maintenance . . . . . . . . . . . . . . 49
Replacing the lamp . . . . . . . . . . . . . 49
Cleaning and replacing the air lter . . 51
Other care ....................53
Troubleshooting . . . . . . . . . . . 54
Related messages . . . . . . . . . . . . . 54
Regarding the indicator lamps . . . . 55
Shutting the projector down . . . . . . 56
Resetting all settings . . . . . . . . . . . . 56
Phenomena that may be easy
to be mistaken for machine defects . . 57
Specications .............59

PJL7211ViewSonic 3
Projector features / Preparations
• Keep the original packing materials, for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
NOTE
Projector features
Preparations
Checking the contents of package
Your projector should come with the items
shown below. Check that all the items are
included. Require of your dealer immediately if
any items are missing.
(1) Remote control with two AA batteries
(2) Power cord
(3) Computer cable
(4) User’s manuals (Book x1, CD x1)
(4)
(2)
(1)
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
(3)
The projector provides you with the broad use by the following features.
ü This projector realizes the large projection image, even if in a small space.
ü This projector is the bright and value XGA (1024x768 pixels) projector.
XGA is the mainstream native resolution as standard projectors, and this
projector is compatible with up-to UXGA (1600x1200 pixels) by resizing.
ü Computer and Video inputs as well as Component video input supported
through COMPUTER IN port provide you sufcient projection function.

PJL7211ViewSonic 4
Part names
Part names
Projector
(1) Lamp cover
The lamp unit is inside.
(2) Focus ring
(3) Zoom ring
(4) Control panel
(5) Elevator buttons (x 2)
(6) Elevator feet (x 2)
(7) Remote sensor
(8) Lens
(9) Intake vents
(10) Filter cover
The air lter and intake vent
are inside.
(11) Exhaust vent
(12) AC IN (AC inlet)
(13) Rear panel
(14) Security bar
(15) Security slot
►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.
►Do not look into the lens or vents while the lamp is on, since the strong light is
not good for your eyes.
►Do not handle the elevator buttons without holding the projector, since the
projector may drop down.
WARNING
►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air lter
periodically.
►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.
CAUTION
HOT!
HOT! (11)
HOT!
(1) (2) (3) (4)
(7)
(9) (8) (10) (6)
(5)
(6)
(6)
(6)
(13)
(14) (12)
(4)
(11)
(1)
(15)
(13)
HOT!

PJL7211ViewSonic 5
Part names
Control panel
(1) STANDBY/ON button
(2) INPUT button
(3) MENU button
It consists of four cursor buttons.
(4) POWER indicator
(5) TEMP indicator
(6) LAMP indicator
Rear panel
(1) COMPUTER IN port
(2) Shutdown switch
(3) VIDEO port
►Use the shutdown switch only when the projector is not
turned off by normal procedure, since pushing this switch stops operation of the
projector without cooling it down.
CAUTION
(1)(2)(3)
(1) (3)(2) (4)
(6)(5)

PJL7211ViewSonic 6
Part names
Remote control
(1) VIDEO button
(2) COMPUTER button
(3) SEARCH button
(4) STANDBY/ON button
(5) ASPECT button
(6) AUTO button
(7) BLANK button
(8) MAGNIFY - ON button
(9) MAGNIFY - OFF button
(10) MY SOURCE/DOC.CAMERA button
(11) VOLUME - button
(12) FREEZE button
(13) MY BUTTON - 1 button
(14) MY BUTTON - 2 button
(15) KEYSTONE button
(16) POSITION button
(17) MENU button
(18) ▲/▼/◄/► cursor buttons
(19) ENTER button
(20) ESC button
(21) RESET button
(22) Battery cover
Back of
the remote control
* These buttons don’t work.
(2)
(1)
(6)
(5)
(12)
(8)
(9)
(15)
(13)
(16)
(18)
(20)
(10)
(4)
(3)
(7)
*
*
(11)
*
*
(14)
(17)
(19)
(21)
(22)
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
►When one of the buttons marked with “*” was pressed, a message
“NOT AVAILABLE” appears on the screen.
• The VOLUME - button only works when being pressed with the RESET
button to change the remote signal frequency. Otherwise, a message “NOT
AVAILABLE” appears.
NOTICE

PJL7211ViewSonic 7
Setting up
Install the projector according to the environment and manner the projector will be
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
a Screen size (diagonal) b Projection distance (±10%)
c1 , c2 Screen height (±10%)
On a horizontal surface Suspended from the ceiling
• Keep a space of 30 cm or more between the
sides of the projector and other objects such
as walls.
• For the case of installation in a special state
such as ceiling mount, the specied mounting
accessories and service may be required.
Before installing the projector, consult your
dealer about your installation.
Setting up
Screen size
(diagonal)
4 : 3 screen 16 : 9 screen
Projection distance Screen
height
Screen
height
Projection distance Screen
height
Screen
height
min. max. min. max.
type
(inch) m m inch m inch cm inch cm inch m inch m inch cm inch cm inch
30 0.8 0.8 33 1.0 40 38 15 8 3 0.9 36 1.1 44 35 14 2 1
40 1.0 1.1 45 1.4 54 51 20 10 4 1.2 49 1.5 59 47 19 3 1
50 1.3 1.4 56 1.7 68 64 25 13 5 1.6 62 1.9 74 59 23 3 1
60 1.5 1.7 68 2.1 82 76 30 15 6 1.9 74 2.3 89 71 28 4 2
70 1.8 2.0 80 2.4 96 89 35 18 7 2.2 87 2.7 104 82 32 5 2
80 2.0 2.3 91 2.8 110 102 40 20 8 2.5 99 3.0 119 94 37 6 2
90 2.3 2.6 103 3.1 123 114 45 23 9 2.8 112 3.4 135 106 42 6 2
100 2.5 2.9 114 3.5 137 127 50 25 10 3.2 124 3.8 150 118 46 7 3
120 3.0 3.5 137 4.2 165 152 60 30 12 3.8 150 4.6 180 141 56 8 3
150 3.8 4.4 172 5.2 207 191 75 38 15 4.8 187 5.7 225 176 69 10 4
200 5.1 5.8 230 7.0 276 254 100 51 20 6.4 250 7.6 301 235 93 14 5
250 6.4 7.3 287 8.8 345 318 125 64 25 8.0 313 9.6 376 294 116 17 7
300 7.6 8.8 345 10.5 414 381 150 76 30 9.5 376 11.5 452 353 139 21 8
b
abc1
c1 c2 c2

PJL7211ViewSonic 8
Setting up
►Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in re and/or electric
shock.
• Do not place the projector on an unstable, slanted or vibrational surface such
as a wobbly or inclined stand.
• Do not place the projector on its side, front or rear position.
• Consult with your dealer before a special installation such as suspending from
a ceiling or somewhere else.
►Place the projector in a cool place, and ensure that there is sufcient
ventilation. The high temperature of the projector could cause re, burns and/or
malfunction of the projector.
• Do not stop-up, block or otherwise cover the projector’s vents.
• Keep a space of 30 cm or more between the sides of the projector and other
objects such as walls.
• Do not place the projector on metallic thing or anything weak in heat.
• Do not place the projector on carpet, cushions or bedding.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place anything near the projector lens or vents, or on top of the
projector.
• Do not place anything that may be sucked into or stick to the vents on the
bottom of the projector. This projector has some intake vents also on the
bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector in a bathroom or the outdoors.
• Do not place anything containing liquid near the projector.
►Use only the mounting accessories the manufacturer specied, and leave
installing and removing the projector with the mounting accessories to the
service personnel.
• Read and keep the user’s manual of the mounting accessories used.
WARNING
►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector near humidiers, smoking spaces or a kitchen.
►Position the projector to prevent light from directly hitting the projector’s remote
sensor.
CAUTION
Arrangement (continued)

PJL7211ViewSonic 9
VIDEO OUT
RGB OUT
COMPONENT VIDEO OUT
Y CB/PBCR/PR
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations to
connect them. To input component video signal to the projector, an RCA to D-sub
cable or adapter is required. For more information, please see the description of
the COMPUTER IN item of the INPUT menu.
VCR/DVD player PC
► Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
WARNING
►Turn off all devices and unplug their power cords prior
to connecting them to projector. Connecting a live device to the projector
may generate extremely loud noises or other abnormalities that may
result in malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about
non-accessory cables which may be required a specic length or a ferrite
core by the regulations. For cables with a core only at one end, connect
the end with the core to the projector.
► Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed.
CAUTION

PJL7211ViewSonic 10
Setting up
• Be sure to read the manuals for devices before connecting them to
the projector, and make sure that all the devices are suitable to be connected
with this product. Before connecting to a PC, check the signal level, the signal
timing, and the resolution.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals
which are not supported by this projector.
- Although the projector can display signals with resolution up to UXGA
(1600X1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable’s connector ts the
port to connect with. And be sure to tighten the screws on connectors with
screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’
s external RGB output. (Set the laptop PC to CRT display or to simultaneous
LCD and CRT display.) For details on how this is done, please refer to the
instruction manual of the corresponding laptop PC.
• When the picture resolution is changed on a PC depending on an input,
automatic adjustment function may take some time and may not be completed.
In this case, you may not be able to see a check box to select “Yes/No” for the
new resolution on Windows. Then the resolution will go back to the original.
It might be recommended to use other CRT or LCD monitors to change the
resolution.
• In some cases, this projector may not display a proper picture or display
any picture on screen. For example, automatic adjustment may not function
correctly with some input signals. An input signal of composite sync or sync on
G may confuse this projector, so the projector may not display a proper picture.
NOTE
About Plug-and-Play capability
Plug-and-Play is a system composed of a PC, its operating system and
peripheral equipment (i.e. display devices). This projector is VESA DDC 2B
compatible. Plug-and-Play can be used by connecting this projector to a PC
that is VESA DDC (display data channel) compatible.
• Take advantage of this feature by connecting a computer cable to the
COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Please use the standard drivers in your PC as this projector is a Plug-and-
Play monitor.
Connecting your devices (continued)

PJL7211ViewSonic 11
Setting up
Connecting power supply
1. Put the connector of the power cord into the
AC IN (AC inlet) of the projector.
2. Firmly plug the power cord’s plug into the
outlet. In a couple of seconds after the
power supply connection, the POWER
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in re and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
WARNING
Using the security bar and slot
AC IN Power cord
A commercial anti-theft chain or wire up to
10 mm in diameter can be attached to the
security bar on the projector.
Also this product has the security slot for
the Kensington lock.
For details, see the manual of the security
tool.
►Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.
WARNING
►Do not place anti-theft chain or wire near the exhaust vents. It
may become too hot.
CAUTION
• The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
NOTE
Security bar
Security slot
Anti-theft chain or wire
Please remember that when the DIRECT ON function
activated, the connection of the power supply make
the projector turn on.

PJL7211ViewSonic 12
Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you will not use the remote control for
long period, remove the batteries from the remote control and store them in a safe place.
1. Holding the hook part of the battery
cover, remove it.
2. Align and insert the two AA batteries
(HITACHI MAXELL, Part No.LR6 or R6P)
according to their plus and minus terminals
as indicated in the remote control.
3.
Replace the battery cover in the direction of the arrow and snap it back into place.
►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in re, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specied. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
WARNING
21 3

PJL7211ViewSonic 13
Remote control
Changing the frequency of remote control signal
The accessory remote control has the two choices on signal
frequency, Mode 1:NORMAL and Mode 2:HIGH. If the remote
control does not function properly, attempt to change the
signal frequency.
In order to set the Mode, please keep pressing the
combination of two buttons listed below simultaneously for
about 3 seconds.
(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons
(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons
Please remember that the REMOTE FREQ. in the SERVICE
item of the OPTION menu of the projector to be controlled
should be set to the same mode as the remote control.
(1)(2)
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
30º 30º
Approx.
3 m
About the remote control signal
The remote control works with the projector’s remote
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor)
within 3 meters about.
• The remote control signal reected in the screen or the like may be
available. If it is difcult to send the signal to the sensor directly, attempt to
make the signal reect.
• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.
• The remote control may not work correctly if strong light (such as direct
sun light) or light from an extremely close range (such as from an inverter
uorescent lamp) shines on the remote sensor of the projector. Adjust the
position of projector avoiding those lights.
NOTE

PJL7211ViewSonic 14
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
Power on/off
1. Make sure that the power cord is rmly and
correctly connected to the projector and the
outlet.
Turning on the power
2. Make sure that the POWER indicator is
steady orange.
3. Press the STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and the POWER
indicator will begin blinking in green. When the power
is completely on, the indicator will stop blinking and light in steady green.
Power on/off
To display the picture, select an input signal according to the section “Selecting an
input signal”.
►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
WARNING
1. Press the STANDBY/ON button on the projector or the remote control. The
message “Power off?” will appear on the screen for about 5 seconds.
Turning off the power
2. Press the STANDBY/ON button again while the message appears.
The projector lamp will go off, and the POWER indicator will begin blinking
in orange. Then the POWER indicator will stop blinking and light in steady
orange when the lamp cooling is complete.
Do not turn the projector on for about 10 minutes or more after turning it off.
Turning the projector on again too soon could shorten the lifetime of some
consumable parts of the projector.
STANDBY/ON button
POWER indicator
• Turn the power on/off in right order. Please power on the projector
prior to the connected devices.
• This projector has the function that can make the projector automatically turn
on/off. Please refer to the DIRECT ON and AUTO OFF items of the OPTION
menu.
• Use the shutdown switch only when the projector is not turned off by normal
procedure.
NOTE

PJL7211ViewSonic 15
Operating
Operating
1. Press COMPUTER button on the remote control to
select the COMPUTER IN port.
COMPUTER button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE
MY SOURCE /
DOC. CAMERA button
1. Press the MY SOURCE / DOC. CAMERA button on
the remote control. The input signal will be changed
into the signal you set as MY SOURCE.
● This function also can use for document camera. Select
the input port that connected the document camera.
1. Press the INPUT button on the projector.
Each time you press the button, the projector switches its
input port from the current port as below.
Selecting an input signal
INPUT button
● While ON is selected for the AUTO SEARCH item in the
OPTION menu, the projector will keep checking the ports
alternately till an input signal is detected.
COMPUTER IN ó VIDEO
1. Press VIDEO button on the remote control to select the
VIDEO port.
VIDEO button
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
1 2
ESC
ENTER
MENU
RESET
COMPUTER
MY SOURCE/
AUTO
MAGNIFY
PAGE
UP
VOLUME
DOWN
࡯
ON
OFF
㧗
FREEZE