ViewSonic VBC100 User manual

VBC100
myViewBoard Sens
User Guide

2
Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding
the world’s expectations for technological evolution, innovation, and simplicity.
At ViewSonic®, we believe that our products have the potential to make a positive
impact in the world, and we are confident that the ViewSonic® product you have
chosen will serve you well.
Once again, thank you for choosing ViewSonic®!

3
Compliance Informaon
FCC Statement
This device complies with part 15 of FCC Rules. Operaon is subject to the following
two condions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operaon.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cauoned that changes or modicaons not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
Warning: Use only power supplies listed in the user instrucons.
AVERTISSEMENT: Ulisez uniquement les sources d'alimentaon menonnées dans
les instrucons d'ulisaon.
For Canada
• This Class B digital apparatus complies with Canadian ICES-3(B)/ NMB-3(B).
• Cet appareil numérique de la classe B est conforme à la norme ICES-3(B)/ NMB-
3(B) Canada.

4
CE Conformity for European Countries
The device complies with the EMC Direcve 2014/30/EU and General
Product Safety Direcve 2001/95/EC.
Following informaon is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Direcve 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded baeries or accumulators as unsorted municipal
waste, but use the return and collecon systems available.
If the baeries, accumulators and buon cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the baery has a heavy metal
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more
than 0.004% Lead.

5
Declaraon of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direcve
2011/65/EU of the European Parliament and the Council on restricon of the use of
certain hazardous substances in electrical and electronic equipment (RoHS2
Direcve), and is deemed to comply with the maximum concentraon values issued
by the European Technical Adaptaon Commiee (TAC) as shown below:
Substance Proposed Maximum
Concentraon
Actual
Concentraon
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Bis (2-ethylhexyl) phthalate (DEHP) 0.1% < 0.1%
Butyl benzyl phthalate (BBP) 0.1% < 0.1%
Dibutyl phthalate (DBP) 0.1% < 0.1%
Diisobutyl phthalate (DIBP) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Direcves as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminum containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melng temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.

66
Contents
Compliance Information.............................................. 3
FCC Statement........................................................................................................3
CE Conformity for European Countries ..................................................................4
Declaration of RoHS2 Compliance..........................................................................5
Product Overview........................................................ 8
Package contents....................................................................................................8
Front View ..............................................................................................................9
Rear View..............................................................................................................10
Getting Started.......................................................... 11
Connecting to Power ............................................................................................12
Connecting to a Display Device ............................................................................13
Connecting to an Audio Device ............................................................................13
Connecting to an IFP (OPS Built-in PC) Device......................................................14
Performing Connections ............................................ 15
Installing the Hardware ........................................................................................15
Normal Type.......................................................................................................... 15
ViewBoard Type .................................................................................................... 16
WPD/CDE Type...................................................................................................... 17
Making Connections.............................................................................................18
USB-C Connection ................................................................................................. 18
HDMI Connection.................................................................................................. 18
DC In...................................................................................................................... 18
Audio In ................................................................................................................. 18
Stitching Calibration .............................................................................................19
Method 1............................................................................................................... 19
Method 2 .............................................................................................................. 19
Method 3 .............................................................................................................. 19
Stitching Calibration Limitations...........................................................................20

7
OSD UI Description ...............................................................................................21
Image..................................................................................................................... 21
White Balance ....................................................................................................... 21
HDMI Output......................................................................................................... 22
HDMI Output > Resolution settings ...................................................................... 22
Audio ..................................................................................................................... 22
PIR Detector .......................................................................................................... 22
Time Option........................................................................................................... 23
Language ............................................................................................................... 23
AI setting ............................................................................................................... 23
Stitching Calibration .............................................................................................. 24
Save or Exit............................................................................................................ 24
Operating myViewBoard Sens ................................... 25
Installing the myViewBoard Sens App..................................................................25
myViewBoard Sens Startup Screen Description ...................................................26
Troubleshooting ........................................................ 29
Specifications ............................................................ 30
Other Information ..................................................... 32
Customer Service..................................................................................................32
Limited Warranty..................................................................................................33

8
Product Overview
Package contents
Please take a moment to check if all the necessary items are included in the
package. If anything is missing or damaged, please contact your dealer immediately.
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
VBC100
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
Power adapter x 1
AC plug type *4 (US/AU/EU/UK)
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
USB 3.1 Type C Male to
Type C Male 1.8M cable x 1
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
Quick start guide (QSG)
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
USB 2.0 Type C Male to
USB-A Male 1.8M cable x 1
A. Ethylene Vinyl Acetate (EVA 65*18mm)
Apply to WPD/CDE/ViewBoard models.
B. Ethylene Vinyl Acetate (EVA 65*9.5mm)
Apply to WPD/CDE models.
Note:
WPD/CDE = ViewSonic CDE8620, CDE7520,
CDE5520, CDE8620
ViewBoard = IFP8670, IFP6550-3, IFP5550-2

9
Front View
1 9
2
3
10
6
4 5 7 8
No. Components Description
1Internal Microphone Built-in audio input
2 Internal Microphone Built-in audio input
3 Power LED
Indicator LED
LED Behavior LED Status
Wide lens video Red light Remain on
Tele lens video Green light Remain on
Stitching video Red + Green light Remain on
Slide door is closed No light Off
4 PIR Sensor
Passive infrared sensor is an electronic sensor that measures infrared
(IR) light radiating from objects in its field of view and is used in
PIR-based motion detectors.
5Light Level Sensor Measures internal or external light levels.
6 Humidity/Temperature Sensor Measures relative humidity and temperature.
7Wide Camera Lens FOV-D = 146.6° ± 5° camera lens
8Tele Camera Lens FOV-D = 58.4° ± 5°camera lens
9 Slider Door Power on/off switch
10 Clip VBC100 fixed bracket clip

10
Rear View
1
5
2 3 4
No. Components Description
1Audio In
External audio source input.
Note: Attaching an external audio source disables the built-in microphone.
2 DC In DC jack 5V, system power input connector.
3 HDMI OUT V1.4B (Type A) port. Connect to devices with HDMI input function.
4USB-C
USB 2.0 for data transmission, network signal output,
and an extension for audio and video.
Note: For privacy concerns, no video output is produced.
5Camera key:
Cursor Up / Down / Left / Right / Enter

11
Geng Started
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1

12
Connecng to Power
To connect your myViewBoard Sens to a power source, perform the following:
1. Connect one end of the power cord to the AC adapter and the other end to a
power outlet.
2. Connect the AC adapter to the DC-in jack of your myViewBoard Sens.
1
2

13
Connecng to a Display Device
Use an HDMI cable to connect to an external display.
1. Connect one end of the HDMI cable to the HDMI port of the myViewBoard Sens.
2. Connect the other end of the HDMI cable to the HDMI port of a display device.
HDMI cable
Monitor
Connecng to an Audio Device
Use a 3.5mm audio jack cable to connect to an audio device
(ex: wireless microphone).
Note: Aaching an external audio source disables the built-in microphone.
Wireless Microphone

14
Connecng to an IFP (OPS Built-in PC) Device
Use an USB 3.1 Type C Male to Type C Male (or USB 2.0 Type C Male to USB A Male)
cable to connect to an IFP (OPS Built-in PC) device.
1. Connect one end of the USB 3.1 Type C Male to Type C Male (or USB 2.0 Type C
Male to USB A Male) cable to the USB Type C port of the myViewBoard Sens.
2. Connect the other end of the USB 3.1 Type C Male to Type C Male (or USB 2.0
Type C Male to USB A Male) cable to the USB Type C or USB Type A port of an IFP
(OPS Built-in PC).
IFP(OPS BUILT-IN PC)
USB Type C to
USB Type C cable
USB Type C to
USB Type A cable

15
Performing Connecons
Installing the Hardware
Normal Type
Step 1 Step 2 Step 3
0°± 5° 0°± 5°
0°± 5°0°± 5°
0°± 5°
0°± 5°
Ground Ground
Height 2 ± 0.3M
Step 4
Make sure the surface
texture is aligned
horizontally.
Horizontal angle 0°± 5°

16
ViewBoard Type
0°± 5° 0°± 5°
A
A A
Step 1 Step 2 Step 3
0°± 5°0°± 5°
0°± 5°
0°± 5°
Ground Ground
Height 2 ± 0.3M
Step 4
Make sure the surface
texture is aligned
horizontally.
Horizontal angle 0°± 5°

17
WPD/CDE Type
0°± 5° AA
B
B
0°± 5° A
B
Step 1 Step 2 Step 3
0°± 5°0°± 5°
0°± 5°
0°± 5°
Ground Ground
Height 2 ± 0.3M
Step 4
Make sure the surface
texture is aligned
horizontally.
Horizontal angle 0°± 5°
Note: ViewBoard = IFP8670, IFP6550-3, IFP5550-2
WPD/CDE = ViewSonic CDE8620, CDE7520, CDE5520, CDE8620

18
Making Connecons
VBC100
myViewBoard Sens
Quick Start Guide
Contents
 
2 3
1
USB Type C-Type C
cable
USB Type A - USB Type C cable
HDMI cablePower adapter
Audio source
USB-C Connecon
Connect to a PC/laptop via a USB Type C-Type C cable or USB Type C-Type A cable
to launch the myViewBoard Sens App.
HDMI Connecon
Connect to an IFP/monitor/projector via HDMI cable to display images.
DC In
Input DC + 5.0V (2.0A 10.0W) power via the power adapter.
Audio In
An external audio source (ex: wireless receiver) input.

19
Stching Calibraon
Aer installing the hardware, you need to perform stching calibraon to ensure
that the scene image quality meets the specicaons. You can perform stching
calibraon through the following operaons.
Method 1
When the OSD is o, long press (3 sec.) the up cursor to acvate Stching
calibraon.
Method 2
On the myViewBoard Sens App, long press (3 sec.) the up cursor when the OSD is
o to acvate Stching calibraon.
Method 3
myViewBoard Sens App > Seng > Advance Sengs > Stching Calibraon >
Acvate

20
Stching Calibraon Limitaons
Note that stching calibraon may encounter issues under the following condions:
1. Objects are too near to the camera.
2. Objects within the same stch ROI window are located at very dierent depth
elds.
3. Objects within the same stch ROI window have the same periodic paern.
4. Objects that have no visible edges can cause issues during stching.
Fig. 1 Esmated blind Areas for producon line’s 6m calibraon