Viking MIRAGE VK632 Instruction manual

MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 1 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
1. DESCRIPTION
Viking Mirage®Quick Response Extended Coverage Concealed Pendent Sprinkler
VK632 and VK634 are thermosensitive glass-bulb spray sprinkler designed for
installation on concealed pipe systems where the appearance of a smooth ceiling is
desired. The glass bulb operating element and special deflector characteristics meet
the challenges of quick response extended coverage standards.
The sprinkler is pre-assembled with a threaded adapter for installation with a low-
profile cover assembly that provides up to ½” (12.7 mm) of vertical adjustment. The
two-piece design allows installation and testing of the sprinkler prior to installation of
the cover plate. The The “push-on” and “thread-on” designs of the concealed cover
plate assemblies allow easy installation of the cover plate after the system has been
tested and the ceiling finish has been applied. The cover assembly can be removed
and reinstalled, allowing temporary removal of ceiling panels without taking the
sprinkler system out of service or removing the sprinkler.
The Electroless Nickel PTFE (ENT) coating has been investigated for installation
in corrosive environments and is listed and approved as indicated in the Approval
Charts. The ENT finish is only available for the sprinkler assembly, the cover plate is
not plated.
2. LISTINGS AND APPROVALS
cULus Listed: Category VNIV
Refer to the Approval Chart and Design Criteria for cULus Listing requirements that
must be followed.
3. TECHNICAL DATA
Specifications:
Available since 2007.
Minimum Operating Pressure: 7 psi (0.5 bar)
Maximum Working Pressure: 175 psi (12 Bar).
Factory tested hydrostatically to 500 psi (34.5 bar)
Thread sizes: VK632: 1/2” (15 mm) NPT; VK634: 3/4” (20 mm) NPT
Nominal K-Factors: VK632: 5.6 U.S. (80.6 metric*); VK634: 8.0 U.S. (115.2 metric*)
* Metric K-factor measurement shown is in Bar. When pressure is measured in kPa, divide the metric
K-factor shown by 10.0.
Glass-bulb fluid temperature rated to -65 °F (-55 °C)
Patents Pending
Material Standards:
Sprinkler Body: Brass UNS-C84400
Deflector: Copper UNS-C19500
Deflector Pins: Stainless Steel Alloy
Bulb: Glass, nominal 3 mm diameter
Pip Cap: Leaded Bronze UNS-C31400 or UNS-C31600, or Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel
UNS-S30400
Button: Brass UNS-C36000
Screws: 18-8 Stainless Steel
Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape
Yoke: Phosphor Bronze UNS-C51000
Cover Adapter: Cold Rolled Steel UNS-G10080, Finish: Clear Chromate over Zinc Plating
Cover Assembly Materials:
Cover: Copper UNS-C11000
Base: Brass UNS-C26000 or UNS-C26800
Springs: Nickel Alloy
Solder: Eutectic
Ordering Information: The sprinkler and cover plate must be ordered separately. Refer to Tables 1 and 2.
4. INSTALLATION
Refer to appropriate NFPA Installation Standards.
For Light Hazard Occupancies Only
Replaces Form No. F_080107 Rev 20.2
(Adding venting statement (s))


MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 2 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
5. OPERATION
During fire conditions, when the temperature around the sprinkler approaches its operating temperature, the cover plate detaches.
Continued heating of the exposed sprinkler causes the heat-sensitive liquid in the glass bulb to expand and the bulb to shatter,
releasing the yoke, pip-cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector,
forming a uniform spray pattern to extinguish or control the fire.
6. INSPECTIONS, TESTS AND MAINTENANCE
Refer to NFPA 25 for Inspection, Testing and Maintenance requirements.
7. AVAILABILITY
Viking Sprinklers VK632 and VK634 are available through a network of domestic and international distributors. See The Viking
Corporation web site for the closest distributor or contact The Viking Corporation.
8. GUARANTEE
For details of warranty, refer to Viking’s current list price schedule or contact Viking directly.
TABLE 1: SPRINKLER ORDERING INFORMATION
Instructions:
(1) Select a Sprinkler Base Part Number
(2) Add the suffix for the desired Finish
(3) Add the suffix for the desired Sprinkler Temperature Rating
(4) Order a cover plate (refer to Table 2)
Example:
14613AE = 200 °F (93 °C) Temperature Rated Sprinkler with a standard Brass finish.
SIN
Sprinkler
Base Part
Number
Size 1: Finishes 2: Temperature Ratings
NPT
Inch
BSPT
mm Description Suffix
Sprinkler
Temperature
Classification
Nominal Rating
Max. Ambient
Ceiling
Temperature1
Suffix
VK632 14613 1/2 -- Brass A Ordinary 135 °F (57 °C) 100 °F (38 °C) A
VK634 1453573/4 -- ENT 2,3,6 JN Ordinary 155 °F (68 °C) 100 °F (38 °C) B
Intermediate 175 °F (79 °C) 150 °F (65 °C) D
Intermediate
200 °F (93 °C) 150 °F (65 °C) E
Accessories
Sprinkler Wrenches and tools:
A. Heavy Duty Part Number: 14047W/B4
B. Head Cabinet Wrench Part Number: 140315
C. Optional Small Concealed Cover Plate Installer Tool Part No. 144128
D. Optional Large Concealed Cover Plate Installer Tool Part No. 148678
Sprinkler Cabinet:
Holds up to 6 sprinklers: Part number 01731A.
Footnotes
1. Based on NFPA 13, NFPA 13R, and NFPA 13D. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having
Jurisdiction. Refer to specific installation standards.
2. cULus Listed as corrosion resistant.
3. The corrosion resistant and corrosion proofing coatings have passed the standard corrosion test required by the approving agencies indicated in the Approval Chart. These
tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end-user that the coatings are compatible with or suitable
for the proposed environment. For automatic sprinklers, the ENT coating is applied to all exposed exterior surfaces, including the waterway.
4. Requires a ½” ratchet (not available from Viking).
5. Also optional for removal of the protective cap. Ideal for sprinkler cabinets.
6. The ENT finish is NOT available and NOT cULus Listed for 135 °F (57 °C) temperature-rated sprinklers.
7. Part number 14535 (VK634) is not available with ENT finish.
8. The installer tool is for push-on style cover plates only.

MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 3 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
TABLE 2: COVER PLATE ORDERING INFORMATION
Instructions:
(1) Select a Cover Plate Base Part Number
(2) Add the suffix for the desired Finish
(3) Add the suffix for the required Cover Plate Nominal Rating.
Example:
23190MC/W = 165 °F (74 °C) Temperature Rated, 2-3/4” (70 mm) diameter, Thread-On style Round Cover Plate with a Painted
White finish.
1: Select a Cover Plate Base Part Number3
2: Select a Finish
Thread-On Style Push-On Style
Base Part
Number
Size
Inch (mm) Type Base Part
Number
Size
Inch (mm) Type Description Suffix5
23190 2-3/4 (70) Round 23447 2-3/4 (70) Round Polished Chrome F
23174 3-5/16 (84) Round 23463 3-5/16 (84) Round Brushed Chrome F-/B
23179 3-5/16 (84) Square 23482 3-5/16 (84) Square Bright Brass B
Antique Brass B-/A
Brushed Brass B-/B
Brushed Copper E-/B
Painted White M-/W
Painted Ivory M-/I
Painted Black M-/B
3: Temperature Rating Matrix1,2
Cover Plate Nominal
Rating (Required)
Temperature
Classification Sprinkler Nominal Rating Sprinkler Maximum Ambient
Ceiling Temperature2Suffix
135 °F (57 °C) Ordinary 135 °F (57 °C) 100 °F (38 °C) A
155 °F (68 °C)
165 °F (74 °C) Intermediate 175 °F (79 °C) 150 °F (65 °C) C
200 °F (93 °C)
Footnotes
1. The sprinkler temperature rating is stamped on the deflector.
2. Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific
installation standards.
3. Part number shown is the base part number. For complete part number, refer to current Viking price list schedule.
4. Where a dash (-) is shown in the Finish suffix designation, insert the desired Temperature Rating suffix. See example above.
5. Square cover plates 23179 and 23482 cULus Listing is for the 135 °F (57 °C) temperature rated cover plate only. Refer to the Approval Chart.
Figure 1: Identification of Custom Paint for Concealed Covers
All custom color painted cover
plates will have an identifying label
affixed to the inside of the cover that
indicates the custom color and will
have a representative sample (a
paint dot) of the paint on the label.
Figure 2: Square Cover Assembly
3-5/16” (84 mm)
F
A
C
T
O
R
Y
A
P
P
L
I
E
D
C
U
S
T
O
M
P
A
I
N
T
C
O
L
O
R

MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 4 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
Approval Chart
Mirage® QR Extended Coverage Concealed Pendent Sprinklers
For Light Hazard Occupancies Only.
Maximum 175 PSI (12 Bar) WWP
Sprinkler Base
Part Number1SIN
Thread Size Nominal
K-Factor Maximum Areas
of Coverage4
Minimum Water Supply
Requirements4
Flow/Pressure
Listings and Approvals3
(Refer also to Design Criteria)
NPT
Inches
BSPT
mm U.S. metric2cULus5FM NYC
Standard Orifice
14613 VK632 1/2 15 5.6 80.6 16’ x 16’
(4.9 m x 4.9 m)
26 gpm @ 21.6 psi
(98.4 L/min @ 1.49 Bar) AW1, BX1 -- See Footnote 6.
14613 VK632 1/2 15 5.6 80.6 18’ x 18’
(5.5 m x 5.5 m)
33 gpm @ 34.7 psi
(124.9 L/min @ 2.39 Bar) AW1, BX1 -- See Footnote 6.
14613 VK632 1/2 15 5.6 80.6 20’ x 20’
(6.1 m x 6.1 m)
40 gpm @ 51.0 psi
(151.4 L/min @ 3.52 Bar) CW1, DX1 -- See Footnote 6.
Large Orifice
1453510 VK634 3/4 20 8.0 115.2 16’ x 16’
(4.9 m x 4.9 m)
26 gpm @ 10.6 psi
(98.4 L/min @ 0.73 Bar) AW1, BX1 -- See Footnote 6.
1453510 VK634 3/4 20 8.0 115.2 18’ x 18’
(5.5 m x 5.5 m)
33 gpm @ 17.0 psi
(124.9 L/min @ 1.17 Bar) AW1, BX1 -- See Footnote 6.
1453510 VK634 3/4 20 8.0 115.2 20’ x 20’
(6.1 m x 6.1 m)
40 gpm @ 25.0 psi
(151.4 L/min @ 1.72 Bar) CW1, DX1 -- See Footnote 6.
Sprinkler Temperature Ratings
A - 135 °F (57 °C)9and 155 °F (68 °C)
B - 175 °F (79 °C) and 200 °F (93 °C)
C - 135 °F (57 °C)9
D - 175 °F (79 °C)
Cover Plate Temperature Ratings7
W - 135°F (57°C) cover 231901, 234471or 231741. 234631
(large diameter), or 231791, 234821(square cover)
X - 165°F (74°C) cover 231901, 234471or 231741. 234631
(large diameter)
Cover Plate Finishes8
1 - Polished Chrome, Brushed Chrome,
Bright Brass, Antique Brass, Brushed
Brass, Brushed Copper, Painted White,
Painted Ivory, and Painted Black
Footnotes
1. Part number shown is the base part number. For complete part number, refer to current Viking price list schedule.
2. Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0.
3. This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals.
4. For areas of coverage smaller than shown, use the “Minimum Water Supply Requirement” for the next larger area listed. Flows and pressures listed are per sprinkler.
5. Listed by Underwriter’s Laboratories, Inc. for use in the U.S. and Canada for Light Hazard occupancies with smooth, flat, horizontal ceilings only.
6. Meets New York City requirements, effective July 1, 2008.
7. The 135 °F (57 °C) cover has an orange label. The 165 °F (74 °C) cover has a white label.
8. Painted finish consists of Polyester Baked Enamel. Other paint colors are available on request with the same listings as the standard paint colors. Listings and approvals
apply for any paint manufacturer. Contact Viking for additional information.
9. The ENT finish is NOT available and NOT cULus Listed for 135 °F (57 °C) temperature-rated sprinklers.
10.
Part number 14535 (VK634) is not available with ENT finish.
NOTE:Custom colors are indicated on a label inside the cover assembly. Refer to Figure 1.

MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 5 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
DESIGN CRITERIA
(Also refer to the Approval Chart)
cULus Listing Requirements: Mirage®Quick Response Extended Coverage Concealed Pendent Sprinklers VK632 and VK634 are cULus Listed for
installation in accordance with the latest edition of NFPA 13 for extended coverage pendent spray sprinklers:
• Limited to Light Hazard occupancies, with smooth, flat, horizontal ceilings only.
• Minimum spacing allowed is 8 ft. (2.4 m) unless baffles are installed in accordance with NFPA 13.
• Minimum distance from walls is 4 in. (102 mm).
• Maximum distance from walls shall be no more than one-half of the allowable distance between sprinklers. The distance shall be measured
perpendicular to the wall.
• The sprinkler installation and obstruction rules contained in NFPA 13 for extended coverage pendent spray sprinklers must be followed.
• Venting is required.
• Concealed sprinklers must NOT be installed in positive pressure plenums.
IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer Bulletin Form No.
F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with
the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar
organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable.
Sprinkler and Adapter
Assembly
• Protective cap
removed
• Use wrench
14031**
Step 1:
Carefully slide the wrench
sideways around the
deflector and pins
Sprinkler Wrench
Part No. 14047WB**
2-1/4” (57 mm)
diameter opening
required in the
ceiling.
Step 2:
Carefully press the wrench upward and
turn slightly to ensure engagement with the
sprinkler wrench flats.
NEVER install the sprinkler by applying the installation
wrench across the frame arms. DO NOT overtighten. Use
only the designated sprinkler wrenches, Part Numbers
14047WB** or 14031**. A leak-tight seal should be achieved
by turning the sprinkler clockwise 1 to 1-1/2 turns beyond
finger tight.
Sprinkler
wrench flat
Sprinkler
frame arms
** A 1/2” ratchet is required (Not available from us.)
Figure 3: Sprinkler Installation and Proper Wrench Usage

MIRAGE®QUICK RESPONSE
EXTENDED COVERAGE
CONCEALED PENDENT
SPRINKLERS (VK632 AND VK634)
TECHNICAL DATA
Form No. F_080107 Rev 01 April 2023
Page 6 of 6
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com
3/4” (20 mm) NPT
Maximum
Maximum
Minimum
Minimum
Figure 5: Sprinkler Dimensions and Cover Installation-VK634
2-1/4”
(57 mm)
NOTE: Upon sprinkler activation, the deector descends
to approximately 13/16” (21 mm) below the sprinkler body.
2-11/16”
(68 mm)
2-3/16
(56 mm)
Figure 4: Sprinkler Dimensions and Cover Installation-VK632
1/2” (15 mm) NPT
2-3/4” (70 mm) or
3-5/16” (84 mm)
NOTE: Upon sprinkler activation, the deector descends
to approximately 13/16” (21 mm) below the sprinkler body.
2-3/4” (70 mm) or
3-5/16” (84 mm)
2-1/8”
(54 mm)
2-1/2”
(64 mm)
2”
(51 mm)
Replaces Form No. F_080107 Rev 20.2
(Adding venting statement (s))

BULLETIN
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
CARE AND HANDLING
OF SPRINKLERS
Page 1 of 4
Form No. F_091699 18.10.11 Rev 16.1.P65
SPRINKLERS ARE FRAGILE - HANDLE WITH CARE!
General Handling and Storage:
• Store sprinklers in a cool, dry place.
• Protect sprinklers during storage, transport, handling, and after installation.
• Use the original shipping containers. DO NOT place sprinklers loose in boxes, bins,
or buckets.
• Keep sprinklers separated at all times. DO NOT allow metal parts to contact sprinkler
operating elements.
For Pre-Assembled Drops:
• Protect sprinklers during handling and after installation.
• For recessed assemblies, use the protective sprinkler cap (Viking Part Number 10364).
Sprinklers with Protective Shields or Caps:
• DO NOT remove shields or caps until after sprinkler installation and there no longer is
potential for mechanical damage to the sprinkler operating elements.
• Sprinkler shields or caps MUST be removed BEFORE placing the system in
service!
• Remove the sprinkler shield by carefully pulling it apart where it is snapped together.
• Remove the cap by turning it slightly and pulling it off the sprinkler.
Sprinkler Installation:
• DO NOT use the sprinkler deflector or operating element to start or thread the sprinkler
into a fitting.
• Use only the designated sprinkler head wrench! Refer to the current sprinkler tech-
nical data page to determine the correct wrench for the model of sprinkler used.
• DO NOT install sprinklers onto piping at the floor level.
• Install sprinklers after the piping is in place to prevent mechanical damage.
• DO NOT allow impacts such as hammer blows directly to sprinklers or to fittings, pipe,
or couplings in close proximity to sprinklers. Sprinklers can be damaged from direct or
indirect impacts.
• DO NOT attempt to remove drywall, paint, etc., from sprinklers.
• Take care not to over-tighten the sprinkler and/or damage its operating parts!
Maximum Torque:
1/2” NPT: 14 ft-lbs. (19.0 N-m)
3/4” NPT: 20 ft-lbs. (27.1 N-m)
1” NPT: 30 ft-lbs. (40.7 N-m)
WARNING
Any sprinkler with a loss of liquid from the glass bulb or damage to the fusible element should be destroyed. Never install sprinklers
that have been dropped, damaged, or exposed to temperatures exceeding the maximum ambient temperature allowed. Sprinklers that
have been painted in the field must be replaced per NFPA 13. Protect sprinklers from paint and paint overspray in accordance with
the installation standards. Do not clean sprinklers with soap and water, ammonia, or any other cleaning fluid. Do not use adhesives
or solvents on sprinklers or their operating elements.
Refer to the appropriate technical data page and NFPA standards for complete care, handling, installation, and maintenance
instructions. For additional product and system information Viking data pages and installation instructions are available on
the Viking Web site at www.vikinggroupinc.com.
CORRECT
(Original container used)
INCORRECT
(Placed loose in box)
CORRECT
(Protected with caps)
INCORRECT
(Protective caps not used)
CORRECT
(Piping is in place at the
ceiling)
INCORRECT
(Sprinkler at floor level)
CORRECT
(Special installation
wrenches)
INCORRECT
(Designated wrench not
used)

Replaces Form No. F_091699 Rev 16.1
(Added P65 Warning)

BULLETIN
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
CARE AND HANDLING
OF SPRINKLERS
Page 2 of 4
Form No. F_091699 18.10.11 Rev 16.1.P65
PROTECTIVE SPRINKLER SHIELDS AND CAPS
General Handling and Storage:
Many Viking sprinklers are available with a plastic protective cap or shield temporarily covering the operating elements. The snap-
on shields and caps are factory installed and are intended to help protect the operating elements from mechanical damage during
shipping, storage, and installation. NOTE: It is still necessary to follow the care and handling instructions on the appropriate sprin-
kler technical data sheets* when installing sprinklers with bulb shields or caps.
WHEN TO REMOVE THE SHIELDS AND CAPS:
NOTE: SHIELDS AND CAPS MUST BE REMOVED FROM SPRINKLERS BEFORE PLACING THE SYSTEM IN SERVICE!
Remove the shield or cap from the sprinkler only after checking all of the following:
• The sprinkler has been installed*.
• The wall or ceiling finish work is completed where the sprinkler is installed and there no longer is a potential for mechanical damage
to the sprinkler operating elements.
SHIELDS AND CAPS MUST BE REMOVED FROM SPRINKLERS BEFORE PLACING THE SYSTEM IN SERVICE!
Figure 1: Sprinkler shield being
removed from a pendent sprinkler.
Figure 2: Sprinkler cap being
removed from a pendent sprinkler.
Figure 3: Sprinkler cap being re-
moved from and upright sprinkler.
HOW TO REMOVE SHIELDS AND CAPS:
No tools are necessary to remove the shields or caps from sprinklers. DO NOT use any sharp objects to remove them! Take care
not to cause mechanical damage to sprinklers when removing the shields or caps. When removing caps from fusible ele-
ment sprinklers, use care to prevent dislodging ejector springs or damaging fusible elements. NOTE: Squeezing the sprinkler cap
excessively could damage sprinkler fusible elements.
• To remove the shield, simply pull the ends of the shield apart where it is snapped together. Refer to Figure 1.
• To remove the cap, turn it slightly and pull it off the sprinkler. Refer to Figures 2 and 3.
Refer to the current sprinkler technical data page to determine the correct sprinkler wrench for the model of sprinkler used.
Never install sprinklers that have been dropped, damaged, or exposed to temperatures in excess of the maximum ambient
temperature allowed.
* Refer to the appropriate current technical data pages for complete care, handling, and installation instructions. Data
pages are included with each shipment from Viking or Viking distributors. They can also be found on the Web site at www.
vikinggroupinc.com.

BULLETIN
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
CARE AND HANDLING
OF SPRINKLERS
Page 3 of 4
Form No. F_091699 18.10.11 Rev 16.1.P65
GENERAL HANDLING AND STORAGE INSTRUCTIONS:
• Do not store in temperatures exceeding 100 °F (38 °C). Avoid direct sunlight and confined areas subject to heat.
• Protect sprinklers and cover assemblies during storage, transport, handling, and after installation.
-- Use original shipping containers.
-- Do not place sprinklers or cover assemblies loose in boxes, bins, or buckets.
• Keep the sprinkler bodies covered with the protective sprinkler cap any time the sprinklers are shipped or handled, during testing of the system, and
while ceiling finish work is being completed.
• Use only the designated Viking recessed sprinkler wrench (refer to the appropriate sprinkler data page) to install these sprinklers. NOTE: The protective cap is
temporarily removed during installation and then placed back on the sprinkler for protection until finish work is completed.
• Do not over-tighten the sprinklers into fittings during installation.
• Do not use the sprinkler deflector to start or thread the sprinklers into fittings during installation.
• Do not attempt to remove drywall, paint, etc., from the sprinklers.
• Remove the plastic protective cap from the sprinkler before attaching the cover plate assembly. PROTECTIVE CAPS MUST BE REMOVED FROM
SPRINKLERS BEFORE PLACING THE SYSTEM IN SERVICE!
Refer to the appropriate current technical data pages for complete care, handling, and installation instructions. Data
pages are included with each shipment from Viking or Viking distributors. They can also be found on the Web site at www.
vikinggroupinc.com.
Concealed Sprinkler and Adapter
Assembly with Protective Cap
CAUTION: CONCEALED COVER ASSEMBLIES ARE FRAGILE!
TO ASSURE SATISFACTORY PERFORMANCE OF THE PRODUCT, HANDLE WITH CARE.
Cover Plate Assembly
(Pendent Cover 12381 shown)
Concealed Sprinkler and Adapter
Assembly (Protective Cap Removed)

BULLETIN
The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058
Telephone: [phone] Technical Services: 877-384-5464 Fax: [phone] Email: [email protected]
CARE AND HANDLING
OF SPRINKLERS
Page 4 of 4
Form No. F_091699 18.10.11 Rev 16.1.P65
USE THE FOLLOWING PRECAUTIONS WHEN HANDLING WAX-COATED SPRINKLERS
Many of Viking’s sprinklers are available with factory-applied wax coating for corrosion resistance. These sprinklers MUST receive
appropriate care and handling to avoid damaging the wax coating and to assure satisfactory performance of the product.
General Handling and Storage of Wax-Coated Sprinklers:
• Store the sprinklers in a cool, dry place (in temperatures below the maximum ambient temperature allowed for the sprinkler temperature rating. Refer
to Table 1 below.)
• Store containers of wax-coated sprinklers separate from other sprinklers.
• Protect the sprinklers during storage, transport, handling, and after installation.
• Use original shipping containers.
• Do not place sprinklers in loose boxes, bins, or buckets.
Installation of Wax-Coated Sprinklers:
Use only the special sprinkler head wrench designed for installing wax-coated Viking sprinklers (any other wrench may damage
the unit).
• Take care not to crack the wax coating on the units.
• For touching up the wax coating after installation, wax is available from Viking in bar form. Refer to Table 1 below. The coating MUST be repaired after
sprinkler installation to protect the corrosion-resistant properties of the sprinkler.
• Use care when locating sprinklers near fixtures that can generate heat. Do not install sprinklers where they would be exposed to temperatures exceed-
ing the maximum recommended ambient temperature for the temperature rating used.
• Inspect the coated sprinklers frequently soon after installation to verify the integrity of the corrosion resistant coating. Thereafter, inspect representative
samples of the coated sprinklers in accordance with NFPA 25. Close up visual inspections are necessary to determine whether the sprinklers are being
affected by corrosive conditions.
Never install sprinklers that have been dropped, damaged, or exposed to temperatures in excess of the maximum ambi-
ent temperature allowed.
Refer to the appropriate current technical data pages for complete care, handling, and installation instructions. Data
pages are included with each shipment from Viking or Viking distributors. They can also be found on the Web site at www.
vikinggroupinc.com.
TABLE 1
Sprinkler Temperature Rating
(Fusing Point)
Wax Part
Number Wax Melting Point Maximum Ambient Ceiling Temperature1Wax Color
155 °F (68 °C) / 165 °F (74 °C) 02568A 148 °F (64 °C) 100 °F (38 °C) Light Brown
175 °F (79 °C) 04146A 161 °F (71 °C) 150 °F (65 °C) Brown
200 °F (93 °C) 04146A 161 °F (71 °C) 150 °F (65 °C) Brown
220 °F (104 °C) 02569A 170 °F (76 °C) 150 °F (65 °C) Dark Brown
286 °F (141 °C) 02569A 170 °F (76 °C) 150 °F (65 °C) Dark Brown
1 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having
Jurisdiction. Refer to specific installation standards.
Replaces Form No. F_091699 Rev 16.1
(Added P65 Warning)