Viking PW200001 Service manual

VIKING RANGE CORPORATION, P.0. DRAWER 956, GREENWOOD, MS. USA

2
TABLE OF CONTENTS
Installation------------------------------------------------------------------------------------------- 3
Reversible Door------------------------------------------------------------------------------------- 4
Electrical Requirements---------------------------------------------------------------------------- 4
Troubleshooting Guide----------------------------------------------------------------------------- 5
Wiring Diagram------------------------------------------------------------------------------------- 6
Parts List---------------------------------------------------------------------------------------------- 7

3
WINE COOLER
Unpack;
• Remove banding from carton. Lift carton up
and off the wine cooler.
• Remove all tape and packaging material
from the outside and inside of the cabinet.
• Keep all carton packaging until your wine
cooler has been thoroughly inspected and
found to be in good condition.
Locate Unit;
This unit must be installed in an area protected
from the elements, such as wind, rain, water
(spray or drip).
• Place unit so the front side will be
completely unobstructed to provide proper
air flow.
• Area should be well ventilated with the
temperature above 55°and 110°F. Best
results are obtained at temperatures between
65°and 80°.
• Provisions for electricity should be
determined before placing unit in proper
place.
• The unit may be closed in on the top and
three sides, but the front MUST BE
unobstructed for air circulation and proper
operation. Installation should be such that
the cabinet can be moved for servicing if
necessary.
Leg / Glide Installation;
• Align the four (4) U-clips (nuts) with the
holes in the bottom of the frame as shown in
the assembly sequence section below. Note
the direction of the tangs on the clip. These
must be located on the bottom of the flange
as shown. Incorrect installation, with tangs
on top, will destroy the U-clip and make it
useless.
• Screw glides into U-clips. Glides should be
screwed in until smug and then backed off to
level unit. WARNING: The U-clips
intended for glide use only! Do not place
clips on unit without using glides as this will
scratch or damage the floor surface.
Personal injury may occur.
• After placing unit in position, check to make
certain the unit is level side to side and front
to back.
• Accurate leveling es essential for proper
operation.

4
Reversible Door
You can change the door swing from right to left
hand very easily. Simply unscrew the top hinge
bracket, lift door off of the bottom hinge
bracket. Flip the door, remove the light switch
activator and replace the light switch activator
on the other end of the door. Remove the door
swing pins from the top and bottom hinges.
Move the bottom, right hinge bracket to the
upper, left side of the cabinet and fasten it in
place with its original mounting screws. Move
the top, right hinge bracket to the lower left side
of the cabinet and fasten with its original screws.
Fasten the door swing pin with the round head to
the bottom left hinge, place the plastic washer
over the door swing pin and on the top surface
of the bottom, left hinge. Position the door on
the bottom, left hinge and push the door under
the top, left hinge. Line-up top left hinge hole
with the top door bushing hole and insert screw
down the door swing pin with a 1/8” Allen drive
until its head is flush with the top surface of the
top, left hinge. Reposition the logo. Your
installation is complete.
24” width for cabinet only. 24 ¼” needed for
cabinet and door width clearance if door is to be
recessed between cabinets.
Electrical Requirements
A 120 volt, 60 Hz, AC only 15 amp fused
electrical supply is required. (A time delay fuse
or circuit breaker is recommended.) it is
recommended that a separate circuit, serving
only this appliance, be provided. DO NOT use
an extension cord.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE. DO NOT UNDER ANY
CIRCUMSTANCES REMOVE THE POWER
SUPPLY CORD GROUNDING PLUG.

5
WINE COOLER
Problem Possible Cause / Solution
Odor in cabinet Interior needs cleaning
Noisy operation / cabinet vibrates Cabinet not level; weak floor.
Cabinet light not working Bulb burned out; no power to outlet.
Appliance will not run Temperature control turned to “OFF”; line cord not
Appliance runs too long Prolonged door openings; control set too cold;
Moisture collects inside Too many door openings; Prolonged door openings;
hot, humid weather increases condensation.
Moisture collects on outside surface Hot humid weather increases condensation; as
Interior too hot / too cold Control improperly set; faulty thermostat; relocate
Light Bulb Replacement
IT IS RECOMMENDED THAT YOU
DISCONNEDT THE POWER CORD
BEFORE ATTEMPTING LIGHT
BULB REPLACEMENT.
The unit uses a 15-watt, intermediate base bulb and
is located inside the light shield. The light shield is
on the ceiling of the unit and is held in place be the
use of three screws. Remove the three screws and
light shield to remove the light bulb. Do not place
bulb with a bulb higher than 15 watts.

6
WIRING DIAGRAM
24” Wide Wine Cooler
WARNING: ELECTRICAL GROUNDING INSTRUCTIONS
This appliance is equipped with a three prong grounding plug
for your protection against shock hazard and should be plugged
directly into a properly grounded three prong receptacle. Do not
cut or remove the grounding prong from this plug.

7
VIKING WINE COOLER
PART # DESCRIPTION
GLIDE ASSEMBLY
PW200001 EVAPORATOR ASSEMBLY (42051307)
PW200011 “P” CLAMP & SCREW ASSEMBLY
PW200012 EVAPORATOR PORT CAPS ASSEMBLY
PW200013 TRIM PKG. SCREWS ASSEMBLY
PW200022 COMPRESSOR ASSEMBLY
PW210001 VIKING CABINET ASSEMBLY
PW210003 GRILLE, BLACK ASSEMBLY (41001525)
PW210004 WIRE RACK ASSEMBLY (1220053D)
PW210005 FRONT SHROUD ASSEMBLY
PW210006 WIRE RACK ASSEMBLY (1220050D)
PW210007 WINE RACK ASSEMBLY
PW210008 WINE RACK ASSEMBLY
PW210009 BACK SHROUD AWWEMBLY (41003617)
PW210010 BACK PANEL KIT
PW210011 BASE PLATE ASSEMBLY (41005085)
PW210012 DRIP TRAY ASSEMBLY
PW210013 FAN SHROUD ASSEMBLY (14003626)
PW210014 DRIP PAN ASSEMBLY
PW220001 LIGHT COVER ASSEMBLY
PW220002 LIGHT SHIELD ASSEMBLY
PW220003 BLK - STR - PLT ASSEMBLY (41003658)
PW220004 HINGE ASSEMBLY
PW230001 WIRING LABLS ASSEMBLY
PW230002 LABEL ASSEMBLY R134A
PW230003 EVAPORATOR TRIM ASSEMBLY 61AR
PW230004 T - STAT KNOB ASSEMBLY (41002094)
PW230005 DOOR GASKET ASSEMBLY
PW230006 VIKING DOOR ASSEMBLY
PW230007 VIKING DOOR NAME PLATE
PW230008 VIKING DOOR FRAME ASSEMBLY
PW240002 POWER CORD ASSEMBLY (41005083)
PW240003 DRIER ASSEMBLY
PW240005 FAN ASSEMBLY
PW240007
PW240008 TERMINAL BLOCK ASSEMBLY (41005078)
PW240012 RUN CAPACITOR ASSEMBLY
PW240013 LIGHT ASSEMBLY
PW240014 LIGHT BULB
PW240015 THERMOSTAT ASSEMBLY
PW240016 SWITCH ASSEMBLY (41004651)
PW240017 SWITCH ASSEMBLY (41002960)
PW240018 DRAIN TUBE ASSEMBLY (101002960)
PW24004 CONDENSER ASSEMBLY

Filename: WineCooler07.doc
Directory: D:\VBCODE\IPLUTILS\PDFGenerator\InputData\F90572 Wine Cooler (24in)
Template: C:\Documents and Settings\tomw.EYECOM\Application
Data\Microsoft\Templates\Normal.dot
Title: VIKING WINE COOLER
Subject:
Author: Viking Range
Keywords:
Comments:
Creation Date: 10/12/2001 10:54 AM
Change Number: 6
Last Saved On: 3/28/2003 4:32 PM
Last Saved By: Ken Sievert
Total Editing Time: 4 Minutes
Last Printed On: 3/28/2003 7:06 PM
As of Last Complete Printing
Number of Pages: 1
Number of Words: 224 (approx.)
Number of Characters: 1,278 (approx.)