Villeroy & Boch VICLEAN U+ User manual

Powered by TOTO
Electronic Bidet Seat

Installation Guide
Precautions before installation
Symbols and their meanings
Before installation, be sure to read this installation guide and the separate safety
sheet. Mount parts properly according to the instructions.
●Only turn on the electricity and water supply for the product after all other installation
work has been completed.
●Do not damage the connection components on the water supply hose (C-3).
●The water supply pressure range is between 0.1MPa (dynamic) and 1.0MPa (static) in
Europe. Use the unit within the specified pressurerange.
●The water temperature must be within a range of 0 to 35°C. Make sure the temperature
is within thisrange.
●The ambient temperature during operation must be within a range of 0 to 40°C. Make
sure the temperature is within this range.
●As a water flow test is conducted on each product at the factory, a small amount of
water may remain inside the product. This water does not indicate a problem withthe
product.
●All-pole disconnection incorporated in the fixed wiring shall be provided.
This task must be carried out by the installer.
This function is performed automaticallyby .
Visual confirmation is required for this.
Indicates the workflow direction.
2

Rated power
supply 220 –240V alternating voltage, 50Hz
Rated power
consumption (fluctuating) 845 -855W
Maximum
powerconsumption (fluctuating) 1528W
(At a water supply temperature of0°C)
Power cord
length 0,62m
Check the appropriate type for your mains connection in the table below, and then wire
and install the product correctly.
Prepare an outlet position in advance that conforms to the regulations in your country.
Specifications
3

A-3 A-4 A-5
A-1 A-2
Anti-theft protection for the
remotecontrol
Please ask the home owner if he would
like to have the remote control anti-theft kit
installed before starting installation. Please
leave the anti-theft kit with the owner if it is
notinstalled.
A-7
A-6 A-8
C-1
C-4
C-2
C-3
A-9
Included Parts
4

B-8
B-1 B-2
B-6
B-3
B-7
2x
B-4
Use a soft, damp cloth to prevent
damage to theproduct.
B-9 B-10
B-11
B-5
Ø = 3mm
Ø = 6mm
Required tools/items
5

Without ViConnect. Please follow the indications in this manual.
Characteristics:
•Two water connections are needed, one for the flushing of
the WC and another one for the shower toilet
•When looking towards the wall mount, the electric
connection is located on the left, whereas the water
connection on the right. The connections will not be
visible after the installation
•Before the WC is mounted, the water and electric
connections must be already attached on the wall.
•Before the shower toilet is mounted, the water connection
should be attached to the inlet of the seat.
Connection Possibilities
4

With ViConnect –Please follow manual provided with ViConnect set!
9224 61 00
9218 51 00
9221 15 00
Characteristics:
•Only one water connection is necessary. Both, the seat and the
toilet will use the same one.
•When looking towards the wall mount, the electric connection is
located on the right, whereas the water connection on the left.
The connections will not be visible after the installation
•Before the WC is mounted, the water and electric connections
must be already attached on the wall.
•Before the shower toilet is mounted, the water connection
should be attached to the inlet of the seat.
5
Connection Possibilities

B-8
190mm
180mm
320mm 255mm 220mm
355mm
C-3
B-2
B
A C
Phase
Neutral
Earth
C
D
A-9
30cm
A
D
B
E
Switch the circuit breaker in the fuse box to OFF.
Installation procedure
1
2
6

A-8
A-8
A-6
B-9
A-6
BA
A-6 A-6
3
4 5
6
7
7

C-1
B
AA-6
C-3
8
Press C-1 into A-6 until C-1 engages with aclick.
(After C-1 is mounted, make sure that it cannot
be removed even if it is pulled.)
8

Switch the circuit breaker in the fuse box to ON.
9
9

A-3
A-1
AB
C
Sidewall
Rearwall
300mm
760mm
1060mm
A-1
760mm
1060mm
250mm 390mm 250mm
A-1
11
Mounting the remote control
10
10

B-4
C-4
Holddown
A-1
A
C
C
B
11
13
12 11
Temporarily place the remote control in the position determined in
and check the signal reception atA-1.
11

AØ =3mm
B-5
Ø = 6mm
B-5
A-4
B-1
A-2
A-2 A-1
Anchored by magnet.
B
A-4
B-1
A-5
A-2
13
C
12

A
C
BØ =3mm
B-5
Ø =6mm
B-5
D E
A-4
A-2
A-4
A-5
A-2
A-1
A-2
Ø =3mm
B-5
Ø =6mm
B-5
A-4
B-1
A-2
A-4
B-1
A-5
A-2
A-2
B-1
A-2
12
Anti-theft protection for the remote control
13
13

B-3
C-4
A
A
Holddown
A-1
A-1
B
B
C
Holddown
16
B
B-8
A
B-4
Trial run
Open the water shutoff valve(B-8).
14
15
14

134mm
260mm
547mm
64mm
485mm
220mm
594mm
92°
538mm
392mm
390mm
Dimensions
For information on “How to dismount the mainunit”,
please refer to the separatesheet.
Information for the installer
●Please explain the features and operation of to the customer.
●If the product will not be used for a long time (for example, when it is installed in an
unoccupied, newly constructed building), switch the circuit breaker in the fuse box
to OFF.
15

08-2015
Coloursanddimensionsare subject tocommonlyacceptedtolerances.Subject totechnicalchangesandcolourmodifications.
GERMANY
Villeroy&BochAG
BathroomandWellnessDivision
Headquarter
D -66693Mettlach
EN