VisiConsult VC Security 101775 User manual

Manual 101775
Facial Recognition
+Temperature Measuring
Access Control

S. 2
Table of Content
PRECAUTIONS BEFORE USING......................................................................................... 3
Product Introduction .............................................................................................................. 4
System Introduction ........................................................................................................... 4
Performance Parameters................................................................................................... 4
Product Exterior ................................................................................................................. 6
Interface Description .......................................................................................................... 6
Installation Steps ............................................................................................................... 8
Installation Matters Needing Attention................................................................................ 8
Basic Function Introduction ................................................................................................... 9
User Management ............................................................................................................10
Schedule Management .....................................................................................................10
Report Management .........................................................................................................13
System Settings................................................................................................................13
General Settings ............................................................................................................................ 14
Advanced Settings ......................................................................................................................... 15
Door Setup .......................................................................................................................16
Access Control Settings ................................................................................................................. 16
Bell Setting ........................................................................................................................17
Communication Settings ...................................................................................................17
Communication Settings ............................................................................................................... 18
Server Settings............................................................................................................................... 18
NTP Settings................................................................................................................................... 19
Ethernet Settings........................................................................................................................... 19
Wireless Settings ........................................................................................................................... 20
Information Viewing ..........................................................................................................21
Registration Information ............................................................................................................... 21
Equipment Information................................................................................................................. 22
Use Process.........................................................................................................................23
Hardware Installation ........................................................................................................23
User Registration ..............................................................................................................23
Registration of a face..................................................................................................................... 24
Delete Registration Data ............................................................................................................... 25
Access Control Related Settings .................................................................................................... 25

S. 3
PRECAUTIONS BEFORE USING
Dear customers, thank you for purchasing our company's access control products. Before
using this product, please read the operation manual carefully, which will help to improve
your efficiency of using this product.

S. 4
Product Introduction
System Introduction
Dynamic face attendance access control machine with face, card and password recognition,
temperature detection and other door functions, can provide enterprises with safe access
control, attendance, health monitoring and other management. The face access control
management system is composed of face access control machine (hereinafter referred to as
face machine), electric lock controller, electric lock, door magnetic, alarm, door button,
doorbell, access control power, computer and management software.
The face machine is mainly responsible for the registration of user information and the
verification and identification of daily access for employees as well as visiting guests. When
used as access control, users do not need to use the key, only through identity
authentication can they achieve the door opening action. If the company already uses an
access control, employees only need to verify their access.
The body temperature detection function USES a medical high precision sensor, the
recognition distance will affect the detected temperature value.
The management system is mainly used for the parameter setting, data backup and
downloading of the access record of the equipment.
The face machine can also be run separately offline, without connection management
software, when not connected to the management software it will not be able to use the user
expiration date and real-time monitoring function.
Face machine and management software communication connection:
TCP/IP, WIFI communication.
Performance Parameters
1. CPU processor 4 cores, 1.2G, memory 1G DDR3
2. Operating system: LINUX smart operating system
3. 200W pixel HD color camera \100W infrared fake check camera
4. Medical high precision sensor MLX90614DCI
error ±0.2°C
optimal range for temperature measurement: 50CM
5. LED highlight fill light (automatically controlled according to ambient light)
6. Operating voltage and current: DC12V±10%,
Static working current: 510mA
action current: 800mA
7. Ambient light: 0-50000Lux

S. 5
8. Liquid crystal display (LCD): 5.0-inch capacitive touch screen 1280*720
9. Operating temperature: -15℃~ +45°C
(storage temperature: -10℃~ +65°C)
operating relative humidity: 20% ~ 90%
(storage humidity: 20% ~ 90±2%)
10. User capacity: 3000-10000-20000 pieces
User records: 200,000 pieces
Verification of real-time photos: 10000 pieces
11. Verification method: temperature measurement
face recognition
temperature measurement
12. Distance of dynamic face recognition: 0.5-3m
Optimal temperature measurement distance: 50CM;
13. Communication methods TCP/IP wired communication
WIFI wireless communication
USB flash drive
14. The data collection: U disk export data report, or computer software through
the network connected to the device to collect data;
15. Language display: simplified Chinese
English
16. Voice prompt: high definition humanized voice
17. Door magnetic signals: 1-way door magnetic signal input
doorbell control
relay output alarm signal
door lock signal control 2 ways
18. 485 output \U disk interface \ door switch
19. Weigand signal input \ Weigand output
Note: the factory function parameters of the product shall be subject to the contract.

S. 6
Product Exterior
Interface Description
1. Access control interface J12 (12P interface on the upper back of the device) definition:
Line
sequence
Definition
Description
1
ALARM-
Alarm signal
2
ALARM+
Alarm signal
3
NO
Normally Open
4
COM
Door lock common end
5
NC
Normally Closed
6
OPEN
Positive opening signal
7
GND
Open ground
8
SEN
Door magnetic signals
9
BELL-
Doorbell ground
10
BELL+
Positive bell signal
11
FIRE1
Fire input alarm 1
12
FIRE2
Fire input alarm 2
2. Access control interface J8 (4P interface below the back of the device) definition:
Line
sequence
Definition
Description
1
RJ-45-1
TCP_TX+Signal feet
2
RJ-45-2
TCP_TX-Signal feet
3
RJ-45-3
TCP_RX+Signal feet

S. 7
3. Access control interface J8 (2P interface below the back of the device) definition:
Line
sequence
Definition
Description
1
12V
Power feed 12V
2
GND
Power supply ground
wire
4. Access control interface J8 (2P interface below the back of the device) definition:
Line
sequence
Definition
Description
1
GND
USB Ground wire
2
USBD+
USB D+ signal data foot
3
USBD-
USB D- signal data foot
4
5V
USB 5V Power supply
foot
5. Access control interface J13 (9P interface below the back of the device) definition:
Line
sequence
Definition
Description
1
485-B
485 - B foot
2
485-A
485 - A foot
3
GND
Ground wire
4
D1-IN
Weigand signal input 1
pin
5
D0-IN
Weigand signal input 0
pin
6
GND
Ground wire
7
D0-OUT
Weigand signal output 0
feet
8
D1-OUT
Weigand signal output 1
feet

S. 8
Installation Steps
The face machine is mounted (if mounted on the brake machine, additional mounting bracket
is required). The detailed installation steps are as follows:
1. Positioning: according to the standard fixed plate screw hole.
2. Drilling: use standard screws to position the hole into a suitable hole.
3. Fixed hanging plate: put the fixed hanging plate in the proper position of the punching
area, and then screw into the hole position and tighten respectively.
4. Hang: hang the face machine on a fixed hanging board (the bottom of the machine is
about 1.4 meters above the ground).
5. Boot: refer to the wiring diagram to connect the equipment, the final power can be
automatically started.
6. Connect to the computer: this product connects to the computer in the ways of TCP/IP
and WIFI network communication. Firstly, select the communication mode between the
face machine and the management computer, and set the communication parameters on
the face machine. Install the management software on the management computer and
set the parameters related to the face machine communication. The parameters set must
be consistent with the parameters set on the face machine (please refer to the software
manual for the specific operation).
Installation Matters Needing Attention
1. the access control machine is recommended to be installed indoors. If it is used outdoors,
it must not be exposed to direct sunlight camera and rain. At the same time, it is
recommended to use sunshade and cooling equipment in summer.
2. the exit button should not be wound too long. The closer it is to the machine, the better.
3. the lock power supply should be as close as possible to the machine and the electric
lock.
4. the relay in the machine can directly control the electric lock, and the maximum bearing
current is 30VDC/2A.

S. 9
Basic Function Introduction
The face machine can carry on the menu choice, the keyboard input and each kind of setting
flexibly through the function key and the number key. The first-level menu includes eight
major items:
User management
Schedule system
Report management
System settings
Door setup
Bell settings
Communication settings
Information viewing
Under each menu, there are different subordinate second-level, third-level and fourth-level
menus, which can be operated accordingly.

S. 10
User Management
Enter the user management menu, and its secondary menu includes registered user, user
preview, department Settings, information export, information import (see the figure below).
A user can register a face, a password, or a card (optional).
Schedule Management
The main interface menu enters the attendance rule menu, and the secondary menu
includes four menus:
attendance rule
shift setting
record setting
record viewing
(see the following pictures)

S. 11
Value Settings
Instruction
Late
Attendance record. Allows a few minutes late.
All logs within the specified timeframe are counted as valid
punch records.
Early leave
Attendance record. Leave a few minutes earlier. All logs
within the specified timeframe are counted as valid punch
records.
Content Settings
Value Setting
Instructions
Class period
Period of time
Shifts can be set up to 3 times a day,
morning shift, middle shift, night shift
(overtime), and up to 24 shifts overall.

S. 12
Content Settings
Value Setting
Instructions
Log Warning
0-1000
After setting the value, the interface will
prompt the warning of full data when
there are 0-1000 logs left from the
1000000 maximum logs. If the
verification record is full, the access
control will overwrite the verification
record that has been read.
Log Interval
0-60 minutes
This is the time setting for a valid
clocking interval
Save Photo
Yes or No
Select whether to turn on the photo
save feature
Content Settings
Value Setting
Instructions
Record to view
Work number
and time
period
In the interface of the input and query
period, you can query the entry and
exit record of the job number

S. 13
Report Management
The main menu interface enters the report management menu, and the secondary menu
includes the menu of company name, scheduling table export, scheduling table import,
attendance sheet output, attendance output, etc. (see the following figure).
Content Settings
Value Setting
Instructions
Company name
-------
You can set the company name or
abbreviation so that the exported report
title is the company name
Schedule export
-------
You can export the schedule of the
people you have entered
Schedule import
-------
You can import the schedule you set
on your computer
Time sheet
output
-------
Attendance records can be exported
for all personnel at certain times
The output of
check on work
attendance
-------
This is the entry and exit record for all
personnel exported
System Settings
The main menu enters the system Settings menu, which includes the secondary menu
normal Settings and advanced Settings.
General Settings can set time, time zone, language, temperature detection, temperature
measurement + identity identification, alarm temperature value, temperature calibration
value, temperature calibration plus or minus, temperature accuracy level, volume, return to
the main interface time, screen saver time.
Advanced Settings include total number of managers, confirmation method, card number
format, report encryption, delete all users, delete all records, live detection, equipment self-
inspection, restore factory Settings, firmware upgrade, etc. (see the figure below).

S. 14
General Settings
Content Settings
Value Setting
Instructions
Time
Date / Time
Use up and down keys to select the
correct date number to set the date of
the access control machine.
Timezone
GMT+8
You can set GMT+/-
Language
Chinese /
English
Including simplified Chinese and
English. The contents displayed on the
interface are simplified Chinese and
English. The factory default is
simplified Chinese.
Temperature
measurement
Yes / No
Whether to enable the temperature
detection function
Stranger
temperature
measurement
Yes / No
Temperature detection function for
identification. "No" means the
registered staff can take the
temperature. "yes" does not need to
register to take the temperature.
Alarm
temperature
-----
Set the alarm value of abnormal
temperature
Temperature
calibration value
-----
Set the temperature deviation
calibration value. When there is an
error with other metering equipment,
the calibration is carried out by setting
the value. For example, if the value is
set to "15", the calibration is 1.5
degrees
Temperature
calibration
positive and
negative
Positive /
Negative
"Forward Direction" is to increase the
calibration value on the original value,
and then output the display and record;
"Negative" is to subtract the calibration
value from the original value and then
output the display and record

S. 15
Exact grade of
temperature
High /
medium / low
The rigor of the distance and the
position of the face at the temperature.
"Height" is the strictest alignment, the
highest temperature measurement
accuracy
The volume
0~10
Set values 0-10 to confirm the volume
level. 0 is silent and 10 is maximum
volume.
Return interface
time
0-30 seconds
Set the time to return to the main
screen after brushing or punching
Screen saver
time
0-1439
seconds
Select this option to set the screen
saver time according to personal
preferences; The factory default value
is 60s.
Advanced Settings
Content Settings
Value Setting
Instructions
Max Admin
1~10
Set the total number of face machine
managers. The factory default is 5.
Verify Mode
-------
Face/card/password
card + password
password + face
card +face
etc.
Card Type
--------
10D / 8D / 2H+4H
Protect Excel
Yes / No
Sets whether the exported report
needs to be encrypted
Delete all user
--------
Delete all user data in the device
Delete all log
--------
Delete all attendance data records in
the equipment
Live testing
Yes / No
Turn on vivisection detection

S. 16
Device self-
checking
--------
Check whether the lamp is normal
factory data
reset
-------
When you select this, return all
Settings to the factory default
The firmware
update
-------
Used to update firmware, the new
firmware must be downloaded to the U-
disk to operate
Door Setup
Enter the access control setting menu from the main menu, which includes the door setup
(access control), the time period settings, the user setting of access control, the group
confirmation time, and the definition of combination of unlocking. The details are as follows:
Access Control Settings
Content Settings
Value Setting
Instructions
Wiegand output
Work number /
Card number
Select the number Weigand outputs as
the work number or the card number
Weigand Bit
26 bit / 34 bit
Select the bit of the Weigand output
Lock Delay
0-200 seconds
Set the delay closing time after
opening the door
Alarm
Yes / No
Choose whether to turn on the alarm
(open door alarm and illegal door
alarm)
Alarm off
-----
Turn off the alarm that has appeared
and resolve the alarm
Sensor Mode
NG
Set whether the door magnet is open
and choose open or closed
Magnetic door
delay
0-200 seconds
Door magnetic alarm time

S. 17
Using multiplayer
Yes / No
Whether to enable multiplayer
authentication mode
Simultaneous
confirmation
number
1-5
The total number of people who
validate the schema simultaneously
Bell Setting
The main menu goes into bell setting, which includes bell number and bell period.
Communication Settings
The main menu enters the communication Settings, including the communication Settings,
server Settings, NTP, wired Settings, wireless Settings, etc.
Communication Settings include machine number, port number, communication password
and communication mode.
Server Settings include transmission, server, server port
NTP includes NTP, NTP server
Wired Settings include allow, DHCP, IP address, subnet mask, default gateway, DNS server
IP, and MAC address.
Wireless Settings include allow, select network, DCHP, IP address, subnet mask, default
gateway, DNS server.

S. 18
Communication Settings
Content Settings
Value Setting
Instructions
Device No
0-65535
Use up and down keys to select the
correct date number to set the date of
the access control machine.
Port No
-------
You can set GMT+/-
Net Password
0-9999999
Set the access password for the
communication. The password length
is 0-7 digits
Mode
-------
You can choose between LAN and
wan
Note: the device number is the only identification of this machine. If there is an access
control machine with the same number in the network, it cannot work correctly and the
computer access control management software will get attendance data confusion, so please
pay special attention to the uniqueness of this setting when networking.
Server Settings
Content Settings
Value Setting
Instructions
To transfer
Yes/No
Determine whether you need to
connect to the server
Server
-------
Server IP address or domain name
Server port
-------
The server port number, which defaults
to 80

S. 19
NTP Settings
Content Settings
Value Setting
Instructions
NTP
Yes/No
Determine whether you need to
connect to an NTP server and
synchronize network time
NTP Server
-------
NTP server IP address or domain
name
Ethernet Settings
Content Settings
Value Setting
Instructions
Enable
Yes/No
To determine if you want to open a
wired connection to the network,
connect the symbol to the first icon of
the main interface
DHCP
Yes/No
Confirm whether to turn on automatic
fetch IP. Default is no
IP Address
192.168.000.25
Sets the IP address of the machine to
be accessed during TCP/IP
communication
Netmask
255.255.255.000
Sets the subnet mask of the local LAN
for TCP/IP communication
Gateway
192.168.010.001
Sets the default gateway for the local
LAN for TCP/IP communication
DNS Serve
192.168.010.001
MAC Address
---------
The MAC address of the machine,
which is unique and not repeatable.
Note: the IP address is unique in the local LAN. The default gateway must be the same as
the default gateway on the local LAN.

S. 20
Wireless Settings
Content Settings
Value Setting
Instructions
Enable
Yes/No
To determine whether to open a
network wireless connection, connect
the symbol to the third icon in the
main interface
Search
---------
A list of WIFI router names is
automatically displayed when a WIFI
network is available
DHCP
Yes/No
Confirm whether to turn on automatic
fetch IP. Default is no
IP Address
192.168.000.25
Set up the IP address of the access
machine when WIFI communication
Netmask
255.255.255.000
Set the local LAN subnet mask for
WIFI communication
Default Gateway
192.168.010.001
Default gateway for local LAN when
setting up WIFI communication
DNS Server
192.168.010.001