Vision Fitness R2250HRT User manual

Assembly
Guide
R2250HRT
STEP-THRU SEMI-RECUMBENT FITNESS BIKE

1
STEP
2
STEP
3
STEP
4
STEP
Assembly
Guide
R2250HRT
STEP-THRU SEMI-RECUMBENT FITNESS BIKE
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter
here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12.
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness
Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place
and partially threaded in before completely tightening any ONE screw.

5mm T-Shaped Wrench 15mm Pedal Wrench
Screwdriver
5mm L-Shaped Wrench
TOOLS & PARTS INCLUDED
4mm L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Power Supply, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6mm L-Shaped Wrench

ORANGE BAG BLUE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 20L Screws
Quantity: 2
M8 x 65L Screw
Quantity: 2
SW8 Lockwashers
Quantity: 4 M8 x 20L
Socket-head Cap Screw
Quantity: 4
M8 x 15L Screws
Quantity: 4
SW8 Lockwashers
Quantity: 4
SW6 Lockwashers
Quantity: 8
M6 x 55L Screws
Quantity: 8
M8 x 15L Screws
Quantity: 4
M8 x 20L Screws
Quantity: 2 SW8 Lockwashers
Quantity: 6
M8 x 10L
Set Screw
Quantity: 1

5
1
STEP
• Slide the rear foot into place on the
frame. Secure the foot in place with
two screws (M8x20L) and two lock
washers (SW8) to the outside holes
and with two screws (M8x65L) and
two lock washers (SW8) to the inside
holes. Tighten with the T-shaped 5mm
wrench.
ORANGE BAG
1
STEP
Rear Foot

6
2
STEP
• Place the seat bracket on the seat
frame. Secure in place with four
(M8x20L) socket-head cap screws.
Tighten with the 6mm L-shaped wrench.
• Remove the socket-head cap screw in
front of the seat lever, located on the
right side of the seat frame, with the
4mm L-shaped wrench. Move the seat
lever into position on the bracket.
Reinsert the socket-head cap screw and
tighten with the 4mm L-shaped wrench.
• Take the seat frame handlebar and
connect the heart rate wires (A) exiting
its center to the heart rate wires (B) com-
ing from the seat frame.
• Mount the seat handlebars to the seat
frame with four screws (M8x15L) and
four lock washers (SW8). Tighten with
the 5mm T-shaped wrench.
• Mount the seat bottom cushion to the
seat frame with four screws (M6x55L)
and four lock washers (SW6). Tighten
with the 4mm L-shaped wrench.
• Mount the seat backrest cushion to
the seat frame with four screws
(M6x55L) and four lock washers
(SW6). Tighten with the 4mm L-shaped
wrench.
• Snap the plastic cover onto the rear
of the seat back.
BLUE BAG
2
STEP
Seat Bracket

7
3
STEP
• Slide the console mast cover onto
the console mast.
• Use the wire tie coming from the bot-
tom of the console mast to wrap around
the wire harness and heart rate wires
that are sitting in the frame bracket.
• Pull the wire tie up through the con-
sole mast so the wire harness and heart
rate wires exit the top of the mast.
• Slide the bottom of the console mast
over the frame bracket. Use the
T-shaped 5mm wrench to secure the
four screws (M8x15L) and four lock
washers (SW8) to the sides of the con-
sole mast bracket. Insert a set screw
(M8x10L) to the front edge of the mast
and tighten until snug with the 4mm L-
shaped wrench.
• Mount the console mast handlebar
to the console mast with two screws
(M8X20) and two lock washers
(SW8). Tighten with the T-shaped
5mm wrench.
• With a screwdriver remove the four
mounting screws from the backside of
the console. Connect the heart rate
wires and the wire harness to the pin
connectors on the backside of the con-
sole. Mount the console to the console
mast using the four mounting screws
and the screwdriver.
• Slide the console mast cover into place
so it integrates with the side covers.
• Mount the water bottle cage to the
console mast with the screws located
on the console mast.
PINK BAG
3
STEP
Console Mast
Handlebar
Console
Console Mast
Console Mast
Cover
Frame Bracket

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 5.05 Part #Z22RB102-AG
AG18.35PRD
REV1
4
STEP
• Attach left pedal strap to left pedal
and right pedal strap to right pedal.
• Attach right pedal to right crank arm
and left pedal to left crank arm.
Tighten with the 15mm pedal wrench.
PEDALS
4
STEP