Vision Fitness R2600iNetTV User manual

Assembly
Guide
R2600iNetTV
COMMERCIAL FITNESS BIKE

1
STEP
2
STEP
5
STEP
3
STEP
4
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call
1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
R2600iNetTV
COMMERCIAL FITNESS BIKE
6
STEP

TOOLS & PARTS INCLUDED
5MM Allen Wrench
Screwdriver
5MM L-Shaped Wrench
4MM L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty: 1
Color-coded Hardware Bags
Assembly Guide
Warranty Card
6MM Allen Wrench
CONSOLE BOX
iNetTV Console
Owner’s Guide

HARDWARE INCLUDED
ORANGE BAG GREEN BAG
PINK BAG
BLUE BAG
M8 x 15L Screw
Quantity: 7
M8 x 20L Screw
Quantity: 2
M8x65L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 Lock Washer
Quantity: 6
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
BLACK BAG
M6 x 55L Screw
Quantity: 8
M6 Lock Washer
Quantity: 8
M8 x 15L Screw
Quantity: 4
M8 Lock Washer
Quantity: 8
M8 x 20L Screw
Quantity: 4

5
1
STEP
• Install the rear foot with the four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
(M8x20L). Tighten with the 5MM Allen
wrench.
ORANGE BAG
1
STEP
2
STEP
• Slide the rubber boot onto the
console mast.
• Locate the bundle of wires that
comes from the console mast frame
bracket. Wrap the wire tie coming
from the bottom of the console mast
around the bundle of wires. Pull the
wire tie with the bundle of wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the console mast to the
frame bracket with six lock washers
(M8) and six screws (M8x15L).
Tighten with the 5MM Allen wrench.
Place the seventh screw (M8x15L) in
the rear of the frame bracket and
tighten until snug.
• Slide the console mast boot down
and snap it into place on the side
cover.
• Remove the screws located half
way up the console mast with the
Phillips screwdriver. Attach the water
bottle bracket to the console mast with
these two screws. Insert the water
bottle.
BLUE BAG
2
STEP

6
3
STEP
• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two screws (M8x20L).
Tighten with the 5MM Allen wrench.
PINK BAG
3
STEP
4
STEP
4
STEP
• Remove the six mounting screws
from the back of the console. Set the
console into place on the console
mast and secure it with the six screws
you just removed. Tighten with the
Phillips screwdriver. Connect the wires
to the proper plugs in the back of the
console (see diagram).
CONSOLE
1 - Co-Axial Cable TV
2 - USB - B
3 - USB - A
4 - VGA (PC Video)
5 - Video IN
6 - Audio - R
7 - Audio - L
8 - Microphone
9 - Heart Rate Reciever 1
10 - Heart Rate Reciever 2
11 - 20 Pin Connector
12 - Power Plug
13 - Miles/Kilometers Switch
14 - Data Port
1 2 3 4 5 6 7 8
14
9
10
11
12
13
WIRES

7
5
STEP
• Attach the seat frame to the sliding
seat bracket using four socket head
cap screws (M8x20L) and the 6MM
Allen wrench.
• Connect Wires A on the seat
handlebar to Wires B on the sliding
seat bracket. Attach the seat
handlebars to the sliding seat bracket
using four lock washers (M8) and four
screws (M8x15L). Tighten with the 5MM
Allen wrench.
GREEN BAG
Wires B
Wires A
5
STEP

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z26RB60-AG1825PRD
AG18.25PRD
REV1
6
STEP
6
STEP
• Secure the Lumbar controlled seat
back and the seat bottom to the seat
frame with eight lock washers (M6)
and eight screws (M6x55L). Tighten
with the 4MM Allen wrench.
• Snap the plastic seat cover into
place on the back of the Lumbar
controlled seat.
BLACK BAG