Vision Fitness R2200 User manual

Assembly
Guide
R2200 AND R2200HRT
SEMI-RECUMBENT FITNESS CYCLE

1
STEP
2
STEP
3
STEP
4
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
R2200 AND R2200HRT
SEMI-RECUMBENT FITNESS CYCLE

TOOLS & PARTS INCLUDED
5mm Allen Wrench 15mm Pedal Wrench
Screwdriver
5mm L-Shaped Wrench
4mm L-Shaped Wrench
6mm L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Power Supply, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap (
R2200HRT Only )
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card

ORANGE BAG BLUE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 20L Screws
Quantity: 2
M8 x 65L Screw
Quantity: 2
M8 Lockwashers
Quantity: 4 M8 x 20L
Socket-head Cap Screw
Quantity: 4
M8 x 15L Screws
Quantity: 4
M8 Lockwashers
Quantity: 4
M6 Lockwashers
Quantity: 8
M6 x 55L Screws
Quantity: 8
M8 x 15L Screws
Quantity: 5
M8 x 20L Screws
Quantity: 2
M8 Lockwashers
Quantity: 6

5
1
STEP
1
STEP
• Slide the rear foot into place on the
frame. Secure the foot in place with
two screws (M8x20) and two lock
washers (M8) to the outside holes and
with two screws (M8x65) and two
lock washers (M8) to the inside holes.
Tighten with the blue-handled 5mm
allen wrench.
• Slide the rubber sleeve, located on
the rear support tube, into place over
the rear foot.
ORANGE BAG
Rear Foot

6
Seat Frame
B
A
Seat Bracket
R2200HRT
Seat Lever
R2200
2
STEP
2
STEP
• Place the seat bracket on the seat
frame. Secure in place with four
(M8x20) socket-head cap screws.
Tighten with the 6mm L-shaped wrench.
• Remove the socket-head cap screw in
front of the seat lever, located on the
right side of the seat frame, with the
4mm L-shaped wrench. Line-up the seat
lever into position on the bracket.
Reinsert the socket-head cap screw and
tighten with the 4mm L-shaped wrench.
• Take the seat frame handlebar and
connect the heart rate wires (A) exiting
its center to the heart rate wires (B) com-
ing from the seat frame.
• Mount the seat handlebars to the seat
frame with four screws (M8x15L) and
four lock washers (M8). Tighten with the
5mm allen wrench.
• Mount the seat backrest cushion to
the seat frame with four screws
(M6x55L) and four lock washers (M6).
Tighten with the 4mm L-shaped wrench.
• Mount the seat bottom cushion to the
seat frame with four screws (M6x55L)
and four lock washers (M6). Tighten
with the 4mm L-shaped wrench.
R2200HRT ONLY: Snap the plastic
cover onto the rear of the seat back.
BLUE BAG

7
3
STEP
3
STEP
• Slide the console mast cover onto
the console mast.
• Use the wire tie coming from the bot-
tom of the console mast to wrap around
the wire harness and heart rate wires
that are sitting in the frame bracket.
• Pull the wire tie up through the con-
sole mast so the wire harness and heart
rate wires exit the top of the mast.
• Slide the bottom of the console mast
into the frame bracket. Use the 5mm
allen wrench to secure the four screws
(M8x15) and four lock washers (M8)
to the sides of the console mast brack-
et. Use the 5mm L-shaped wrench to
secure the last screw (M8x15) to the
edge of the bracket facing the seat.
Tighten only until snug.
• Mount the console mast handlebar
to the console mast with two screws
(M8X20) and two lock washers (M8).
Tighten with the 5mm allen wrench.
• With a screwdriver remove the four
mounting screws from the backside of
the console. Connect the heart rate
wires and the wire harness to the pin
connectors on the backside of the con-
sole. Mount the console to the console
mast using the four mounting screws
and the screwdriver.
• Slide the console mast cover into place
so it integrates with the side covers.
• Mount the water bottle cage to the
console mast with the screws located
on the console mast.
PINK BAG
Console Mast
Handlebar
Console
Console Mast
Console Mast
Cover
R2200

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 1.05 Part #Z22RB42D-AG
AG18.16PRD
REV4
4
STEP
4
STEP
• Attach left pedal strap to left pedal
and right pedal strap to right pedal.
• Attach right pedal to right crank arm
and left pedal to left crank arm.
Tighten with the 15mm pedal wrench.
PEDALS