Visonic MC-302V PG2 User manual

D-304535 MC-302V PG2 Installation Instructions 1
1. INTRODUCTION
The MC- 302V PG2 is a very thin PowerG
magnetic contact device that is compatible
with PowerMaster control panels. The device
includes a built- in reed switch (that opens
upon removal of a magnet placed near it).
The MC- 302V PG2 sends the alarm
message to the control panel using PowerG
2- way communications protocol. A periodic
supervision or alarm message is transmitted
automatically. The control panel is thus
informed, at regular intervals, of the unit’s
active participation in the system.
The LED lights green/yellow/red, according
to signal strength, upon first insertion of the
battery and for the test period of 15 minutes.
Operating power is obtained from an on-
board 3 V Lithium battery. When the battery
voltage is low, a “low battery” message is
sent to the receiver.
The MC- 302 V is available for 433 MHz, 868
MHz, and 915 MHz. A. Transmission LED B. Magnet
Figure 1: External View
2. INSTALLATION
2.1. Mounting
Caution! This equipment shall be installed by Service Personnel in non-hazardous indoor locations only.
A. Enroll button B. Double-sided adhesive tape
Figure 2: Mounting
MC-302V PG2
Supervised Vanishing Magnetic Contact Device
Installation Instructions

Notes:
lThe required battery is CR2032 Lithium 3V, manufactured by VARTA or another UL-recognized manufacturer, purchased from a Visonic-
approved supplier.
lTo comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance of at least 20 cm from all persons
during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or
transmitter.
lInsert the battery when installing the product but not prior to the installation as this can degrade battery life performance.
1. Insert a “quarter” coin in the slot, as shown in the drawing, and flex to remove the cover
- or, if a “quarter” coin is not available -
Insert a 4 mm flat screwdriver into the slot of the plastic cover, as shown in the drawing, and flex the slot to open that side of the plastic cover.
2. Insert the screwdriver into the slot on the other side of the plastic cover and repeat the procedure, and then remove the cover.
3. Insert the battery at an angle (see drawing) while observing battery polarity and then press down on the battery.
Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the manufacturer's instructions.
4. Peel away the release liners from the two strips of double-sided adhesive tape and attach to the device and magnet.
5. Align the device with the magnet according to the location marks and fasten the device and magnet to the mounting surface. The transmitter
should be mounted on the fixed surface and the magnet on the moving surface.
6. For the 433 or 868 MHz installer models, ensure that the heads of the tightened screws are flat perpendicular to the device surface.
To close the cover complete the following steps:
lInsert the two teeth on the front cover into the corresponding slots on the base.
lWhen the cover is approximately at a 30 degree angle to the base, push into place until you hear a click.
Figure 3: Closing the cover
2.2. Enrollment
Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu. The
following is a general description of the steps through the panel menu:
1. 02:ZONES/DEVICES
2. ADD NEW DEVICES > MODIFY DEVICES
3. ENROLL NOW or > ENTR ID:XXX-XXXX
4. Z06:Contact Sens > ID No. 104-XXXX
5. Z06:LOCATION > Z06:ZONE TYPE > Z06:SET CHIME > Z06:DEV SETTINGS
3. LOCAL DIAGNOSTICS TEST
Before testing, separate the base from the cover (see Figure 2).
A. Put back the cover to return the tamper switch to its normal
(undisturbed) position.
B. Momentarily open the door or window and verify the red LED blinks,
indicating detection.
C. After 2 seconds one of the LEDs blinks 3 times.
The following table indicates received signal strength indication.
LED response Reception
Green LED blinks Strong
Yellow LED blinks Good
Red LED blinks Poor
No blinks No communication
Important! Reliable reception must be assured. Therefore, "poor" signal
strength is not acceptable. If you receive a "poor" signal from the detector,
re-locate it and re-test until a "good" or "strong" signal strength is received
(in regions requiring UL-compliant installation, only “strong” signal
strength is permitted).
Note: It is recommended to have a "strong" signal strength and you must
verify the signal strength using the control panel's diagnostic test. For
detailed Diagnostics Test instructions refer to the control panel Installer
Guide.
4. MISCELLANEOUS COMMENTS
Visonic Ltd. wireless systems are very reliable and are tested to high standards. However, due to low transmitting power and limited range (required by
FCC and other regulatory authorities), there are some limitations to be considered:
A. Receivers may be blocked by radio signals occurring on or near their operating frequencies, regardless of the digital code used.
B. A receiver responds only to one transmitted signal at a time.
C. Wireless devices should be tested regularly to determine whether there are sources of interference and to protect against faults.
D-304535 MC-302V PG2 Installation Instructions 2

5. COMPLIANCE WITH STANDARDS
The MC-302V PG2 complies with the following standards:
Europe: EN300220, EN301489 EN50130-4, EN61000-6-3, EN60950-1, EN50131-1, EN50131-2-6 and
EN50131-6 Type C.
Certified by Norwegian accredited certification body Applica Test & Certification AS in accordance with
EN50131-1, EN50131- 2-6, EN50131-6, EN50130-4 et EN50130-5
Hereby, Visonic Ltd. declares that the radio equipment type MC-302V PG2 is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.visonic.com/download-center.
USA: FCC - CFR 47 part 15, UL - UL-634
Canada: IC - RSS 210, ULC - ULC C634
The Power G peripheral devices have two- way communication functionality, providing additional benefits as
described in the technical brochure. This functionality has not been tested to comply with the respective
technical requirements and should therefore be considered outside the scope of the product’s certification.
Security Grade Designed according to EN 50131-1, EN-50131-2-6 and EN-50131-6 Type C: this equipment can be applied
in installed systems up to and including Security Grade 2.
Environmental Class EN-50131-2-6 Class II
FCC Compliance Statement
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and
television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such
interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following
measures:
lRe-orient or re-locate the receiving antenna.
lIncrease the distance between the device and the receiver.
lConnect the device to an outlet on a circuit different from the one that supplies power to the receiver.
lConsult the dealer or an experienced radio/TV technician.
Warning! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired
operation.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique
subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
Reed Switch Positions
Wood Supports Iron
Opening Closing Direction Opening Closing
>14 mm >12 mm X* <12 mm >9 mm
>22 mm >20 mm Y** <11 mm >9 mm
>30 mm >27 mm Z*** <12 mm >9 mm
* X axis The distance between the edge of the sensor to the edge
of the magnet in the X axis direction.
**Y axis The distance between A to B in the Y axis direction.
***Z axis The distance between the sensor and the magnet from
the plane defined by the Z axis direction.
Figure 4: Range Coverage Directions
D-304535 MC-302V PG2 Installation Instructions 3

APPENDIX: SPECIFICATIONS
Frequency Band (MHz) 433, 868, 915 (in accordance with the prevailing frequency of your region)
Note: Only devices in frequency band 915MHz are UL/ULC listed
Maximum Tx Power 10 dBm @ 433 MHz, @ 868MHz.
Modulation GFSK
Antenna Built-in loaded inverted-F antenna
Communication Protocol PowerG
Supervision Signaling at 256 sec. intervals
Battery type Varta 3V Lithium CR2032
Battery Life Expectancy
(for typical use at room temperature)
Up to 3 years, not tested by UL/ULC
Low Battery Threshold 2.1 V
Operating Temperature 0°C (32°F ) to 55°C (131°F). UL verified range: 0ºC (32°F) to 49ºC (120°F ) only
Storage Temperature -40°C to 85°C (-104°F to 185°F)
Relative Humidity (RH) Up to 95% non-condensing, UL verified up to a maximum of 85% RH only
Dimensions (LxWxD) 433/868 MHz model: 62 x 25.4 x 7.6 mm (2.5 x 1 x 0.3 in.)
915 MHz model: 62 x 25.4 x 6.4 mm (2.5 x 1 x 0.26 in.)
Weight (including battery) 12g (0.42 oz)
Color White or brown
D-304535 MC-302V PG2 Installation Instructions 4

WARRANTY
VisonicLimited (the “Manufacturer") warrants thisproduct only(the "Product") to the original purchaser only (the
“Purchaser”)against defective workmanship and materials under normal use of the Product for a period of twelve
(12) months from the date of shipment by the Manufacturer.
ThisWarranty is absolutely conditional upon the Product having been properly installed, maintained and operated
under conditions of normal use in accordance with the Manufacturers recommended installation and operation
instructions. Products which have become defective for any other reason, according to the Manufacturers discretion,
such as improper installation, failure to follow recommended installation and operational instructions, neglect, willful
damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the
manufacturer, are not covered by thisWarranty.
There is absolutely no warranty on software, and allsoftware productsare sold as a user license under the terms of
the software license agreement included with such Product."
The Manufacturer does not represent that thisProduct may not be compromised and/or circumvented or that the
Product willprevent anydeath and/or personal injuryand/or damage to propertyresulting from burglary, robbery, fire
or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product, properly
installed and maintained, only reduces the riskof such events without warning and it isnot a guarantee or insurance
that such events willnot occur.
CONDITIONS TO VOID WARRANTY:
Thiswarranty applies onlyto defects in parts and workmanship relating to normal use of the Products. It does not
cover:
•damage incurred in shipping orhandling;
•damage caused bydisaster such asfire, flood, wind, earthquake or lightning;
• damage due to causes beyond the control of the Seller such as excessive voltage, mechanical shock or water
damage;
•damage caused by unauthorized attachment, alterations, modifications or foreign objects being used with or in
conjunction with the Products;
•damage caused byperipherals(unlesssuch peripheralswere supplied bythe Seller;
•defects caused by failure to provide a suitable installation environment for the products;
•damage caused byuse of the Productsfor purposesother than those for which theywere designed;
•damage from improper maintenance;
•damage arising out of anyother abuse, mishandling or improper application of the Products.
ITEMS NOT COVERED BY WARRANTY:
In addition to the items which void the Warranty, the following items shallnot be covered byWarranty: (i) freight cost to
the repair centre; (ii)customsfees, taxes, or VAT that maybe due; (iii) Productswhich are not identified with the Seller's
product label and lot number or serial number; (iv) Products disassembled or repaired in such a manner as to
adverselyaffect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or
tagsreturned for replacement under warranty willbe credited or replaced at the Seller'soption.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR
LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE
MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR
BREACH OF THIS WARRANTYOR ANYOTHER WARRANTIES WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR PUNITIVEDAMAGESOR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE,
PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR
INABILITYTO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY
OTHER CAUSE, EVEN IF MANUFACTURER HASBEEN ADVISED OF THEPOSSIBILITYOF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY
AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.
HOWEVER, IF THE MANUFACTURER IS HEL D LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS
OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY, THE MANUFACTURER'S MAXIMUM LIABILITY (IF
ANY)SHALL NOT IN ANY CASEEXCEED THE PURCHASEPRICE OF THEPRODUCT INVOLVED, WHICH SHALL
BE FIXED AS LIQUIDATED DAMAGES AND NOT ASA PENALTY, AND SHALL BETHE COMPLETEAND EXCLUSIVE
REMEDYAGAINST THE MANUFACTURER.
When accepting the deliveryof the Product, the Purchaser agrees to the said conditions of sale and warranty and he
recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidentalor consequentialdamages, so these limitations
maynot applyunder certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronicequipment or any programs.
The Manufacturers obligationsunder thisWarranty are limited solelyto repairand/or replace at the Manufacturer’s
discretion anyProduct or part thereof that may prove defective. Anyrepairand/or replacement shall not extend the
original Warranty period. The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To
exercise thisWarrantythe Product must be returned to the Manufacturer freight pre-paid and insured. Allfreight and
insurance costsare the responsibilityof the Purchaser and are not included in thisWarranty.
For sales in Israel only:
The Purchaser shallcomplywith the provisionsof the IsraeliConsumer Protection Law – 1981("Consumer Protection
Law") related regulations, including the Israeli Consumer Protection Regulations (Warranty Sticker), 5772- 2012)
("Regulations"), including, without limitation (i) providing itscustomerswith at least the minimum warrantyrequired by
the Consumer Protection Law, and (ii) ensuring that a warranty certificate and a warranty sticker (asdefined in the
Regulations)("Warranty Sticker")shallbe attached to any sold Productsand the date of the sale of the Product to the
consumer or the end-user shallbe added in a readable manner on the WarrantySticker.
In no event shallthe Purchser’s compliance with the Consumer Protection Law and Regulationsexpand anyof the
Manufacturer'swarranty obligations under this warranty, and the Purchaser shall be responsible for any warranty
that it provideswith respect to the Productswhich exceeds or isdifferent from this warranty.
Thiswarranty shallnot be modified, varied or extended, and the Manufacturer does not authorize any person to act
on itsbehalf in the modification, variation or extension of thiswarranty. Thiswarrantyshallapplyto the Product only. All
products, accessories or attachments of others used in conjunction with the Product, including batteries, shall be
covered solelyby theirown warranty, if any. The Manufacturershallnot be liable for any damage or loss whatsoever,
whether directly, indirectly, incidentally, consequentiallyor otherwise, caused by the malfunction of the Product due to
products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This
Warrantyisexclusive to the originalPurchaser and isnot assignable.
ThisWarranty is in addition to and does not affect your legal rights. Anyprovision in this warranty which is contrary to
the Law in the state or countrywere the Product issupplied shallnot apply.
Governing Law:
Thisdisclaimer of warrantiesand limited warranty are governed bythe domestic laws of Israel.
WARNING
The user must follow the Manufacturer’s installation and operationalinstructions including testing the Product and its
whole system at least once a week and to take all necessary precautions for his/her safety and the protection of
his/her property.
* In case of a conflict, contradiction or interpretation between the English version of the warrantyand other versions,
the English version shallprevail.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then
you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
D-304535 MC-302V PG2 Installation Instructions 5
Email: [e-mail]
Internet: www.visonic.com
© VISONIC LTD. 2017 MC-302V PG2 D-304535 (Rev. 9 06/17)