Visonic TOWER CAM PG2 User manual

D-304493 TOWER CAM PG2 Installation Instructions 1
1. INTRODUCTION
The TOWER CAM PG2 is a 2-way, wireless outdoor digital mirror PIR detector
with built-in camera. Activated upon PIR detection or upon demand, the
TOWER CAM PG2 sends clear images to the Monitoring Station for alarm
image verification.
The PIR motion detector’s features are as follows:
lOperates with PowerMaster control panels (version 18 and higher)
lPatented 8 independent quad PIR detectors (Octa-QUAD) operating in
true Quad configuration (patented) with true motion recognition (TMR)
processing for each of the 8 PIR detectors.
lAdvanced Obsidian Black MirrorTM optics (patent pending).
lOptimum performance even in poor weather conditions such as snow, rain,
dust, wind and direct sunlight
lTamper protection prevents opening and removal from wall
lPowerG two-way Frequency Hopping Spread Spectrum FHSS-TDMA
technology - provides robustness and reliability
lBuilt-in link quality indicators enable installer to check signal quality without
physically approaching the control panel.
lRobust housing with recessed window.
lSmart anti masking distinguishes between masking spray and rain.
lAlarm LED is visible in sunlight.
lAutomatic termination of walk-test after 15 minutes.
lMicroprocessor-controlled temperature compensation.
lImmunity to pets weighing up to 18 Kg (40lb) – see Table 1
lBuilt-in swivel bracket
The camera’s features are as follows:
lUp to 10 cameras can be enrolled
lImages multiplexed from all enrolled cameras
lColor and black & white images
lAuto-setup
lCamera tuning by simple walk-test
lDay and night CMOS camera, with near IR illumination. This allows taking
pictures in full darkness without letting the intruder know.
lInstant capture: guarantees capture of fast moving intruder.
lOptional AC power
lAn event records 2 images per second. 10-15 images total
Notes:
1. For UL/ULC installation, the camera feature is not to be enabled in UL
listed product.
2. Pet immunity is not evaluated by UL/ULC.
A. IR LEDs B. Indication LED C. Camera
D. External power LED E. Alarm LED
Figure 1. External View
2. INSTALLATION
2.1. Installation
A. Bracket installation (see Figure 2). Fix the bracket firmly on a stable wall or pillar. The orientation of the fixed bracket must be as parallel as possible
to the surveyed ground surface.
B. Adjust the detector's horizontal and vertical angles (see Figure 3), according to the surveyed ground surface. Set the vertical angle position
depending on the mounting height and coverage distance that you require. See Figure 3 A and Table 1 for details. The information refers to a
relatively flat surveyed area. Verify the correct installation by using the walk test method.
C. Fasten the detector to the bracket (see Figure 2 step 4).
Table 1 - Vertical Adjustment Reference
Mounting Height Coverage Distance
2m / 6.7ft 4m / 13ft 6m / 20ft 8m / 26ft 10m / 33 ft 12m / 39 ft
3.0m / 10 ft - 1 2 2 3 3
2.5m / 8 ft 1 1 2 3 4 4
2.0m / 7 ft 1 2 3 4 5 5
1.5m / 5 ft 2 3 4 5 5 -
TOWER CAM PG2
PowerG, Outdoor Mirror PIR Motion Detector with Anti-
masking and Built-In Camera Installation Instructions

Notes:
1. For UL/ULC listed installations see table 1 to set the correct angle when mounting at a height of 2.4 m (8ft).
2. For UL/ULC listed installations the maximum range of the detection is 10m (33ft).
3. For installation options to reduce the probability of false alarms from pets, see the grayed-in cells in Table 1.
4. For EN installations only and the distance ranges between 11 to 12 m (36 - 39ft), set the PIR sensitivity to "One region".
Event counter: One region
Correct Installation
Incorrect Installation
A. Mark drilling point B. Screw hole for wall tamper C. Drill
D. Fasten E. Three long screws F. Two short screws
Note: The 2 screw holes enable adjustment of the bracket on the wall, if needed, following the walk test.
Figure 2 - Installation
HORIZONTAL ADJUSTMENT (-45° to +45°)
VERTICAL ADJUSTMENT (0° to -10° in 2.5° clicks / steps)
D-304493 TOWER CAM PG2 Installation Instructions 2

Installation Notes:
The top cover should only be accessed by authorized service personnel or manufacturer. Do not obscure the detector field of view with large objects.
Install in position such that expected intruder motion is perpendicular to the zones of detection.
Alarms triggered by conditions such as weather, blowing leaves and brush, or related environmental conditions, etc., need to be considered when
assessing the installation and application. It is recommended that the intrusion detection unit is not to be connected to an alarm initiating circuit but may
be connected to a trouble alarm circuit if nuisance trips are not tolerable.
COVER CLOSURE
1. Release locking 2. Adjust 3. Lock 4. Release locking 5. Adjust
6. Lock 7. Turn cover and push slider 8 & 9. Put back cover 10. Secure with screw
A. Vertical angle steps
Figure 3 - Adjustment and Cover Closure
2.2. Battery Insertion
It is recommended to perform the first batteries insertion on a flat surface (see Figure 4). After battery insertion, the LED will flash for 60 seconds and
then the detector will enter a 15 minutes' local diagnostic mode.
D-304493 TOWER CAM PG2 Installation Instructions 3

A. Tamper switch B. Press firmly to release the bracket C. 1 screw
Steps 7 and 8 are optional for external 7.5 VDC power connection
D. Snap the terminal block into place.
Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to the manufacturer's instructions.
Caution! The battery used in this device may present a risk of fire or chemical burn if mistreated.Do not disassemble, heat above 66°C, or incinerate.
Replace battery with CR17450 Lithium batteries manufactured by EVE only. Dispose of used battery promptly.Keep away from children.Do not
disassemble and do not dispose of in fire.
Note: Tamper protection is mandatory for UL burglary installations.
Figure 4 – Battery Insertion
D-304493 TOWER CAM PG2 Installation Instructions 4

2.3. Enrollment
Refer to the PowerMaster control panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu.
Ageneral description of the procedure is provided in the following flow chart.
Step 1 Step 2 Step 3 Step 4
Enter the Installer menu and select
“02:ZONES/DEVICES”
Select "ADD NEW DEVICE"
See Note 1
Enroll the device (see Figure 5) or
enter the device ID
Select a detector number for the
new detector
02:ZONES/DEVICES ðADD NEW DEVICES
6
ðENROLL NOW or
ENTR ID:XXX-XXXX
ðZ09:Motion Camera
ID No. 142-XXXX
ð
MODIFY DEVICES
Step 5 Step 6 Step 7
Configure Location, Zone Type &
Chime parameters
Enter PARTITIONS.
See Note 2
Assign partitions to the detector by
pressing the ,
and/or buttons on the
panel
Z09.LOCATION
Z09.ZONE TYPE
Z09.SET CHIME
ðZ09/PARTITIONS ðZ09:P1n-- P2....P3nð
ðmeans scroll wwand select OK.
Notes:
[1] If the detector is already enrolled you can configure the detector parameters and assign partitions via the “Modify Devices” option – see Step 2.
[2] PARTITIONS will appear only if PARTITIONING was previously enabled in a panel that supports the Partitioning feature (for further details, see
"Partitioning" in the PowerMaster Installer Guide).
2.4. Configuring the Detector Parameters
Enter the DEVICE SETTINGS menu and follow the configuration instructions for the TOWER CAM PG2 PIR detector as described below.
Option Configuration Instructions
ALARM LED Define whether or not to activate the alarm LED indication.
Optional settings: ON (default) and OFF.
PIR
SENSITIVITY
Define if the detector operates at regular or high PIR sensitivity, or that at least one detection zone must be crossed before an alarm is
triggered (One Region).
Optional settings: LOW (default), HIGH and One Region.
Note: For EN and UL compliance, the detector should be set to "One Region".
DISARM
ACTIVITY
Define whether or not to set the activity time during Disarm mode.
Optional settings: NOT Active (default), YES – no delay, YES + 5s delay, YES + 15s delay, YES + 30s delay, YES + 1m delay, YES +
2m delay, YES + 5m delay, YES + 10m delay, YES + 20m delay and YES+ 60m delay.
OUTDOOR
ANTI-M
Enable or disable the outdoor anti-masking feature.
Optional settings: Disabled (default) and Enabled.
ALARM
Hours
Define whether motion alarms are always enabled or only when dark (at night).
Optional settings: Day and Night (default) and Night only.
Note: For UL/ULC installation, the Alarm Hours feature when enabled for nightprotection should only be used as supplemental
protection to the protection covering the protected area.
IMAGE
COLOR
Define whether the image will be in black & white or color.
Optional settings: Black & White (default) and Color.
IMAGE
RESOLUTION
Set the pixel quality of the image. Select 160 x 120 for lower quality or 320 x 240 for higher quality.
Optional settings: 320 x 240 (default) and 160 x 120.
IMAGE
QUALITY
Set the quality of the image.
Optional settings: High (default) and normal.
IMAGE
BRIGHTNESS
Set the brightness of the image.
Optional settings: Normal (default) -3, -2, -1, +1, +2 and +3.
IMAGE
CONTRAST
Set the contrast of the image.
Optional settings: Normal (default) -3, -2, -1, +1, +2 and +3.
D-304493 TOWER CAM PG2 Installation Instructions 5

2.5. Local Diagnostic Test
A. Set the detector in local diagnostic mode, as follows:
Open the detector’s bottom cover (see Figure 4, steps 1 - 3) and then press and release the tamper switch (see Figure 5). The LED will flash for 60
seconds and then the detector will enter into 15 minutes' local diagnostic mode.
Note: The detector automatically enters into 15 minutes' local diagnostic mode after battery installation or Tamper switch recovery.
B. Adjust the detector in the horizontal plane to cover the required protected area.
C. Walk into the detectors’ field of view. Adjust the vertical plane to receive the maximum number of detections when crossing the entire 90°pattern.
Verify that the LED blinks each time your motion is detected, as you cross one Quad PIR. Then verify that the LED lights steadily for 2 seconds as
you cross the next adjacent Quad PIR. After alarm indication, the LED blinks three times and provides the received signal strength indication (see
Table 2).
Table 2 – Received Signal Strength Indication
LED response Reception
Green LED blinks Strong
Orange LED blinks Good
Red LED blinks Poor
No blinks No communication
Important! Reliable reception must be assured. Therefore, "poor" signal strength is not acceptable. If you receive a "poor" signal from the
detector, re-locate it and re-test until a "Good" or "Strong" signal strength is received.
Note: For detailed Diagnostics Test instructions refer to the control panel Installer's Guide.
The LED blinking, described above, is operative only in Local diagnostic mode. Upon each full detection (LED lights steadily for 2 seconds), the
control panel receives the alarm. If required, perform the detector's horizontal / vertical adjustments (see section 2.1 and Figure 3).
Important! Instruct the user to perform a walk test at least once a week, to verify proper operation of the detector.
D. Place a piece of cardboard on the detector’s front side to deliberately mask the optical window. Verify that after 2 minutes, the yellow LED lights
continuously (see Table 3 below) and the alarm control panel receives the masking alarm.
E. Remove the masking from the detector’s front side. Verify that the LED turns off after 30 seconds.
Table 3 - LED operation
LED Indications Event
Red Alarm LED blinks Stabilization (warm-up 60 sec)
Red Alarm LED ON 0.2 sec. Tamper open / close
Red Alarm LED blinks twice One quad PIR detection in diagnostic mode
Red Alarm LED on 2 sec. Intruder alarm
Yellow Indication LED on AM detection – diagnostic mode
Yellow indication LED blinks slowly (0.2 sec. ON, 30 sec. OFF) AM detection – Normal mode
A. Alarm LED
B. Indication LED
C. Enroll button
D. Tamper switch
Figure 5. TOWER CAM PG2
D-304493 TOWER CAM PG2 Installation Instructions 6

1. COMPLIANCE WITH STANDARDS
Compliance with Standards The TOWER CAM PG2 is designed to comply with the following standards:
Europe (CE): EN 300220, EN 301489, EN 60950, EN 50130-4, EN 50130-5, EN 50131-2-2, EN50131-6,
EN 50131-1 Grade 2 Class IV
The TOWER CAM PG2 is compatible with the RTTE requirements - Directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999 and EN50131-1 Grade 2 Class IV.
UK: This product is suitable for use in systems installed to conform to PD6662:2010 at Grade 2 and
environmental class 4. DD243 and BS8243
Certified by Norwegian accredited certification body Applica Test & Certification AS in accordance with EN
50131-2-2
USA: CFR 47 Part 15 (FCC), UL-639
Canada: RSS 210 (IC), ULC S306
The Power G peripheral devices have two- way communication functionality, providing additional benefits as described in
the technical brochure. This functionality has not been tested to comply with the respective technical requirements and
should therefore be considered outside the scope of the product’s certification.
EN 50131-1 Security Grade Grade 2
EN 50131-1 Environmental Class Class IV
FCC Compliance Statement
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be
verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:
lRe-orient or re-locate the receiving antenna.
lIncrease the distance between the device and the receiver.
lConnect the device to an outlet on a circuit different from the one that supplies power to the receiver.
lConsult the dealer or an experienced radio/TV technician.
Warning! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with FCC Rules Part 15 and with Industry Canada licence- exempt RSS standard (s). Operation is subject to two conditions: (1)
This device may not cause harmful interference and (2) this device must accept any interference that may be received or that may cause undesired
operation.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux
deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique
subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then
you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
APPENDIX: SPECIFICATIONS
OPTICAL
Black Mirror Max. Coverage Up to 12 m (40 ft) / 90°
Detector Technology 8 independent quad PIR detectors operating in true Quad configuration
Figure 6. Coverage Pattern
A. Top view
B. Side view of each detector
C. Image coverage range
Pet Immunity Up to 18 Kg (40 lb)
D-304493 TOWER CAM PG2 Installation Instructions 7

ELECTRICAL
Input Power Two 3V / 2400 mAh, CR17450 Lithium batteries manufactured by EVE.
Battery Life (for typical use) 3 years
Note: Minimum one year, typical 3 years (not verified by UL/ULC)
Low Battery Threshold 4.0 V
Optional Mains Supply Additional to batteries, 7.5 V DC, 1.5 A
Note: For UL/ULC installation, the 7.5 VDC power connection was not evaluated by UL.
FUNCTIONAL
IR Illumination 10 m (33 ft)
Picture Resolution 320x240 pixels QVGA or 160X120 pixels QQVGA
Frame Rate 2 fps
WIRELESS
Frequency Band (MHz) Europe and rest of world: 433-434, 868-869 USA:912-919
Note: Only devices operating in band 912-919 MHz are UL/ULC listed.
Communication Protocol PowerG
Tamper Alert Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored
MOUNTING
Mounting Type Wall mounting
Mounting Height 1.5 – 3.0 m (5 – 10 ft).
Horizontal Adjustment -45° to +45°, in 5° steps
Vertical Adjustment 0° to -10°, in 2.5° steps
ENVIRONMENTAL
Operating Temperatures -35°C to 60°C (-31°F to 140°F)
Note: For UL/ULC installation, evaluated to 66°C
Storage Temperatures -35°C to 60°C (-31°F to 140°F)
Humidity 93% max.
White Light Immunity Above 25000 lux
PHYSICAL
Size (H x L x W) 166 x 147 x 124 mm (6-9/16 x 5-13/16 x 4-7/8”)
Weight (with battery) 700 g (25 oz).
Color White
PATENTS U.S. Patents 7250605 l6818881 l5693943 (other patents pending)
WARRANTY
VisonicLimited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve
(12) months from the date of shipment by the Manufacturer.
ThisWarrantyis absolutelyconditional upon the Product having been properly installed, maintained and operated
under conditions of normal use in accordance with the Manufacturersrecommended installation and operation
instructions. Products which have become defective for any other reason, according to the Manufacturers
discretion, such as improper installation, failure to follow recommended installation and operational instructions,
neglect, willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone
otherthan the manufacturer, are not covered by thisWarranty.
The Manufacturerdoes not represent that this Product may not be compromised and/or circumvented or that the
Product willprevent any death and/or personal injury and/or damageto property resulting from burglary, robbery,
fire or otherwise, or that the Product willin allcases provide adequate warning or protection.The Product, properly
installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or
insurance that such events willnot occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN
NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES
WHATSOEVER, AS AFORESAID.
THE MANUFA CTURER SHA LL IN NO EVENT BE LI ABLE FOR A NY SPECIAL, INDIRECT, INCIDENTA L,
CONSEQUENTI AL OR PUNIT IVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, IN CLUDING LOS S
OF U SE, PRO F IT S, R EVE N UE, OR G O OD W IL L, D I RE C TL Y O R I ND I REC TL Y A R ISI NG FR O M
PURC HASER’S USE OR IN ABI LITY TO USE T HE P ROD UCT, OR FOR LOSS OR DEST RUC TIO N O F
OTHER PROPERTY OR FR OM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED O F
THE POSSIBILITY OF SUCH DAMAGE.
THE M ANUFA CTURE R SHA LL HA VE NO LIAB ILITY FOR ANY D EATH, PERSONAL A ND/OR BODIL Y
IN JU R Y AN D/ OR D A MA GE TO PR OPER TY OR OTHER L OSS W HET HER D IR EC T, I ND I REC T,
INCIDENT AL, CONSEQUENTIAL OR OTH ERWISE, B ASED ON A CLAIM THAT TH E PRODUC T FAILED
TO FUNCTION.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this
limited warranty, THE MANUFACTURER’S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED
THE PURCHASE PRICE OF THE PRODUCT, which shallbe fixed asliquidated damagesand not asa penalty, and
shallbe the complete and exclusive remedyagainst the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he
recognizes having been informed of.
Some jurisdictionsdo not allow the exclusion or limitation of incidentalor consequentialdamages, so these limitations
maynot apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronicequipment or any programs.
The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer’s
discretion any Product or part thereof that may prove defective.Any repairand/or replacement shall not extend the
originalWarranty period. The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To
exercise thisWarrantythe Product must be returned to the Manufacturerfreight pre-paid and insured.Allfreight and
insurance costsare the responsibility of the Purchaser and are not included in thisWarranty.
Thiswarranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act
on itsbehalf in the modification, variation or extension of thiswarranty. This warranty shall applyto the Product only. All
products, accessories or attachments of others used in conjunction with the Product, including batteries, shall be
covered solely bytheir own warranty, if any.The Manufacturer shallnot be liable for any damage or loss whatsoever,
whether directly, indirectly, incidentally, consequentiallyor otherwise, caused by the malfunction of the Product due to
products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This
Warrantyisexclusive to the originalPurchaser and isnot assignable.
ThisWarrantyis in addition to and doesnot affect your legalrights. Anyprovision in thiswarrantywhich iscontraryto the
Law in the state or countrywere the Product is supplied shall not apply.
Warning: The user must follow the Manufacturer’s installation and operational instructions including testing the
Product and its whole system at least once a week and to take allnecessary precautions for his/her safety and the
protection of his/her property.
1/08
EMAIL: [e-mail]
INTERNET: www.visonic.com
© VISONIC LTD. 2016TOWER CAM PG2D-304493 (Rev. 504/16)
D-304493 TOWER CAM PG2 Installation Instructions 8