Visonic MCS-730 User manual

D-301680 1
MCS-730
Fully Wireless Outdoor Siren
Installation Instructions
1. INTRODUCTION
The MCS-730 is a fully wireless outdoor siren, designed for
installation in areas in which wiring action is difficult or impossible.
The siren is compatible with PowerMax control panels such as
PowerMax Pro, PowerMaxComplete, PowerMaxExpress or newer
panels (not compatible with PowerMax and PowerMax+ control panels).
Features
•Siren and strobe light activation: When an identified event
message is received from the compatible PowerMax alarm system,
the siren activates its sounder & strobe light.
Notes:
The sounder is activated for a predefined "Bell Time" (refer to
PowerMax Pro / PowerMaxComplete / PowerMaxExpress installer
guide, par. 4.4), according to local authorities requirements, or until
the system is disarmed, whichever occurs first.
The strobe light operates (every 1 second) during the "Bell Time" +
20 minutes or until the system is disarmed, whichever occurs first.
•Tamper / supervision failure indication: In case of tamper or
supervision failure (loss of communication with the alarm system),
the siren transmits the message to the alarm system and then the
alarm system determines whether the siren should be activated or
not. If the siren does not receive an acknowledge from the alarm
system, the siren will function independently.
•Low battery voltage alert
When the battery voltage is low, a low battery message is sent to
the alarm system. After the low voltage message delivery, at least 2
siren alarms are possible before the siren is totally inactive.
•Power Supply Options: Non-rechargeable battery. Optional - two
non-rechargeable batteries.
•Sound Types: Burglar (between 1400Hz - 1800Hz), Fire, squawk.
•Squawk indications: Squawk (beep) sounds can be used to
indicate alarm system arming (1 squawk) and disarming (2
squawks) by a keyfob (squawk can be enabled from the PowerMax
User menu).
•Strobe Light Color: The siren can be purchased with red, blue,
amber or transparent lens, according to the desired strobe light color.
•Siren activity LED: A flashing LED (optional, at the bottom of the
siren front panel) indicates siren activity (can be disabled by an
internal jumper, see fig. 3, step 8)
•Double Tamper protection: When the siren front panel is
removed or when the siren is removed from the wall, tamper alarm
is sent to the alarm system.
Fig. 1a - External View
Fig. 1b – Mounting Position
IMPORTANT! The MCS-730 siren must be installed on the wall in a
vertical position with the screw pointing to the floor only, as illustrated
in Figure 1b. The importance of correct positioning of the MCS-730 is
to enable the siren to function as a waterproof device.
•2-way full supervision
The siren is fully supervised, 2-way communication device. It
includes a receiver, to receive event messages from the alarm
system, and a transmitter, to periodically transmit its status signal
to the alarm system.
The transmitted signal strength can be measured during the
installation (refer to PowerMax Pro / PowerMaxComplete /
PowerMaxExpress Installer guide, par. 5.2 – Diagnostic Test).
•Self-test feature
Upon pressing the self test switch, siren functional check is performed -
low level sounds and flash light indicate that the siren is serviceable.
MCS-730
Hard wired detector
Smoke detector
Wireless transmitter
Door or window
open/close detector
Motion detector
Remote commander
PowerMax Pro/
PowerMaxComplete/
PowerMaxExpress
Figure 2- Typical Integration with the Alarm System
2. SPECIFICATIONS
Siren Type: One Piezo 109 db min. Sound Pressure Level @ 1m,
1.8-3.5 kHz, sweep frequency 7 Hz. Additional piezo is optional.
Battery: 3.6V/14.5A/H Lithium battery (EVE ER34615M/w200),
Visonic assembly cat. No. 0-9912-K.
Note: Use only the above battery. Dispose of used battery according
to the manufacturer's instructions.
Battery Life Time: 3 years (taking into consideration a typical alarm
of 4 minutes Piezo + strobe operation per week).
Current Consumption: Standby - 180µA average, Operation -
430mA average.
Compliance with Standards: Designed to comply with EN 50131-1
Grade 2 Class 4, EN50131-4, EN301489, EN50130-4, EN50130-5,
ETSI EN 300 220, FCC Part 15, IP55.
Operating Frequency (MHz): 315, 433.92, 868.95
Supervision Time: 5 minutes
Strobe Light: Pulsed @ 1 sec.
Dimensions (LxWxD): 295x186x63mm (11-5/8 x 7-5/16 x 2-1/2 in)
Color: White (with red, blue, amber or transparent lens)
Operating Temperature: -33°C to 70°C (-27.4°F to 158°F), RH
humidity 75%.
Weight (including battery): 970g (34 oz)
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such
modifications could void the user's authority to operate the equipment.
Interference Prevention
This device complies with FCC Rules Part 15. Operation is subject
to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference that
may be received or that may cause undesired operation.
The digital circuit of this device has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in residential installations. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio and television reception. However, there is
no guarantee that interference will not occur in a particular installation. If
this device does cause such interference, which can be verified by
turning the device off and on, the user is encouraged to eliminate the
interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one
which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
Changes or modifications not expressly approved by Visonic Ltd.
could void the user's authority to operate the equipment.

2 D-301680
3. INSTALLATION, TESTING AND ENROLLING
3.1 Installation
Optional step only:
Hang back unit with a screw on
mounting surface to make the next
step (drilling marking) easier.
3
Mark for driling
4
For
tamper
1
Open screw
plastic cover
Using Philips screw-
driver, remove screw
and remove cover.
2
Drill 5 holes
5 6
Fasten with 5 screws
BA
Release catch (A) and open battery cover (B)
7
Optional second
battery and
its connector
Self-test button
Connect battery / optional battery and 9VAC
power to the proper connectors and set the
optional jumpers as desired
8
220/110 VAC
9VAC
9VAC
Siren rear side
LED Enable (ON)/
Disable (OFF)
jumper
AC configuration
Enable (ON)/
Disable (OFF)
jumper
Note: When external
power is used, set the
AC Enable (ON)/
Disable(OFF) jumper
to Enable position
(see step 8)
Note: There are MCS-730 model variations
that are supplied with battery only, or, with
battery and AC adapter.
Figure 3 – Installation
3.2 Self-Test
Press the self test button (see figure 3 step 8). Low level piezo
sounds and flash lights indicate that the siren is fully operational.
3.3 Enrolling
The PowerMax Pro / PowerMaxComplete / PowerMaxExpress alarm
system must recognize the siren's unique identification code for
command delivery and supervision. To enroll the siren into the alarm
system memory,refer to the ENROLLING section of the alarm system
installation instructions, and momentarily press the Self-Test button
(see figure 3 step 8) when you are instructed.
After the enrolling, close the siren's cover and perform diagnostic test,
as described in PowerMax Pro / PowerMaxComplete /
PowerMaxExpress installer guide, DIAGNOSTIC section.
Enrolling cancellation, if required, is also described in the alarm
system Installer Guide, ENROLLING section.
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve
(12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated
under conditions of normal use in accordance with the Manufacturers recommended installation and operation
instructions. Products which have become defective for any other reason, according to the Manufacturers
discretion, such as improper installation, failure to follow recommended installation and operational instructions,
neglect, willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone
other than the manufacturer, are not covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the
Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery,
fire or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product,
properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee
or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN
NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES
WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS
OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM
PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF
OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY
INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this
limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE
EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a
penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and
he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronic equipment or any programs.
The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the
Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement
shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or
reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid
and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this
Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to
act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the
Product only. All products, accessories or attachments of others used in conjunction with the Product, including
batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the
malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in
conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is
contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning: The user must follow the Manufacturer’s installation and operational instructions including testing the
Product and its whole system at least once a week and to take all necessary precautions for his/her safety and
the protection of his/her property.
1/08
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: [phone], FAX: [phone]
VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: [phone]. FAX: [phone]
VISONIC LTD. (UK): UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. TEL: [phone] FAX: [phone].
TEL: [phone] FAX: [phone] PRODUCT SUPPORT: [phone]
VISONIC GmbH (D-A-CH): KIRCHFELDSTR. 118, D-40215 DÜSSELDORF, TEL.: [phone], FAX: [phone]
VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA.
TEL [phone], FAX [phone]. www.visonic-iberica.es
INTERNET: www.visonic.com
©VISONIC LTD. 2009 MCS-730, D-301680 (Rev 3, 07/09)