VIVO HOME VH869 User manual

Assembly Instructions
V-1
LIGHTED VANITY SET
WITH GOLDEN LEGS

•
•
•
•
•
•
•
•
•
For safety and stability, we suggest you have to secure the anti-tip accessories
to the wall to prevent tipping, injury, and property damage.
The product must be assembled and used in accordance with the provisions of the
manual.
Avoid long-term exposure to humid environments to prevent mildew.
Keep the product away from re sources and high temperatures. Do not expose the
product to direct sunlight.
Do not place any hot objects directly on the surface of the product.
If there are any defective or missing parts after unpacking, please cease assembly
immediately and contact us.
Please assemble the item on a spacious surface; to aviod product damage, do not
place the unwrapped product directly on the ground.
Please do not stand or sit on the wooden boards.
Please keep the product away from sharp, pointed objects and corrosive substances
to prevent product damage.
If you nd that the table legs are loose during use, please tighten the screws as soon
as possible to prevent the issue from persisting.
•
•
Children are not allowed to assemble the product. During assembly, keep all small
parts out of the reach of children, as it may be fatal to swallow or inhale them.
Children are forbidden to climb or play on the product. Climbing or playing on the
product may result in serious bodily injuries.
-1-
Note
Warning
Attention

-2-
Parts List and Diagram
X1
X1
X1
X2
Item no. Reference Image Qty.
X1
X1
X1
X2
Item no. Reference Image Qty.
1 2
43
65
87

-3-
Parts List and Diagram
X2
X2
X1
Item no. Reference Image Qty.
X2
X1
X1
X1 X1
Item no. Reference Image Qty.
Assembly tool
9 10
1211
14
15
13

M6*11.8 in.
ST3.5*0.6 in.
ST3.5*1.0 in.
ST4.8*1.6 in.
0.6*0.4 in.
-4-
Parts List and Diagram
X4
X56
X4
X8
Item no. Reference Image Qty.
X2
X22
X4
X6
Item no. Reference Image Qty.
CD
E F
G H
I J
ST3.5x14mm
600mm
23.6 in. 15.7 in.
400mm
ST4.8x40mm
ST3.5x25mm
A B
X16 X16
M6x1.6mm 15x11mm

-5-
M4*0.7 in.
*The package includes extra screws
Parts List and Diagram
Use The Cam Lock and Quickt
Item no. Reference Image Qty. Item no. Reference Image
Round handle USB
MX2 NX1
Qty.
Adhesive Screw Covers
X2 X14
K L
M4x18mm
Quickt: Tighten the quickt until it is
ush against the panel. Do not under-
or over-tighten it.
The cam lock should be inserted before
the quickt. Turn the cam lock clockwise
to tighten. The head of the quickt should
be inserted in the center of the cam lock
where the two panels are joined.

-6-
Assembly Steps
STEP 1 Ix 4 pcs. Gx 4 pcs.
STEP 2 3E
x 1 pc. x 20 pcs.
Assemble Part I onto Part G. Repeat this process three more times so that there
are four total table legs.
Use Parts E to x Parts G on Board 3, as shown in the gure. Use ve Parts E per
each Part G.
x4
3
G
G
G
G
G
I
E

-7-
Assembly Steps
STEP 3 45E
x 1 pc. x 1 pc. x 4 pcs.
Cx 2 pcs.
Use Parts E (2 pcs.) to x Part C1 (1 pc.) on Board 4. Use two more Parts E (2 pcs.) to
x another Part C1 (1 pc.) on Board 5. Please pay attention to the position of the
small holes on Board 4 and Board 5.
4
C1
C1
C1 C2
E
1
2
5

-8-
Assembly Steps
STEP 4 6x 1 pc. Cx 2 pcs. Ex 4 pcs.
Use Parts E (4 pcs.) to x the remaining Parts C1 (2 pcs.) on the two sides of Board 6
(i.e., x one Part C1 and use two Parts E on each side). Please pay attention to the
position of the small holes on Board 6.
6
C1
C1
E

-9-
Assembly Steps
Use Parts F to x Board 4 and Board 5 onto Board 12. Use Parts L to cover the
mounting holes of Parts F.
Use Parts F to x Board 4, Board 5, Board 12, and Board 6 onto Board 3 from below,
as shown in the gure.
STEP 5 F
12 x 1 pc. x 4 pcs. Lx 4 pcs.
STEP 6 Fx 6 pcs.
12
3
5
5
6
12
4
4
F
F
L

-10-
Assembly Steps
STEP 7 113
L
x 1 pc. 2x 1 pc. x 1 pc.
x 2 pcs.
Jx 2 pcs. Fx 4 pcs.
Insert Part 1 into the groove of Part 13. Use Parts F to x Part 1 on Board 2. Then, use
Parts J to x Part 13 on Board 2. Use Parts L to cover the mounting holes of Parts J.
Rotate the assembled part in the previous step 90 degrees clockwise and place it on
the ground, as shown in the gure. Assemble Parts A on the bottom of Board 2.
STEP 8 Ax 8 pcs.
1
2
2
F
L
J
A
A
12
13
90°

Assembly Steps
STEP 9 Bx 8 pcs.
-11-
Use Parts B to x the assembled part in the previous step on Board 4, Board 5,
Board 6, and Board 12, as shown in the gure.
5
6
12
B
4

-12-
Assembly Steps
STEP 10 8x 2 pcs. 9x 2 pcs. 10 x 2 pcs. Fx 8 pcs.
Use Parts F to connect Board 8 and 9 with 10, as shown in the gure. Repeat this step to
get two identical parts.
STEP 11 11 x 2 pcs.
Slide Board 11 into the grooves of Board 8, Board 9, and Board 10. Repeat this step to get
two identical parts.
x2
x2
8
9
10
11
8
9
10
F

-13-
Assembly Steps
STEP 12 7A
x 2 pcs. x 8 pcs.
Assemble Parts A (4 pcs.) on Board 7 (1 pc.). Repeat this step to get two identical parts.
STEP 13 Lx 8 pcs.
Bx 8 pcs.
Use Parts B (4 pcs.) to connect Board 7 (1 pc.) with Board 8 (1 pc.) and Board 9 (1 pc.). Use
Parts L (4 pcs.) to cover the mounting holes of Parts B. Repeat this step to get two identi-
cal parts.
x2
x2
7
7
8
9
A
L
B

Assembly Steps
-14-
Use Parts E (4 pcs.) to x one Part C2 on Board 8 and another on Board 9. Please pay
attention to the position of the small holes on Boards 8 and 9. Repeat this step to get
two identical parts.
STEP 14 Cx 4 pcs. Ex 8 pcs.
x2
8
9
E
E
C2
C2

Assembly Steps
-15-
Use Part K (1 pc.) to x Part M (1 pc.) on Board 7 (1 pc.). Repeat this step to get two
identical drawers.
STEP 15 M
Insert the two drawers into the table.
STEP 16
x 2 pcs. Kx 2 pcs.
x2
7
C2
C1
M
K

-16-
Assembly Steps
STEP 17 Nx 1 pc.
Insert Part N into the socket on the mirror through the hole under Board 2, as shown
in the gure. Connect the other end of Part N to a power source when needed.
Ex 20 pcs.
14 x1 pc.
14
2
N
E
STEP 18
Assemble Parts I onto Parts H. Use Parts E to x Parts H on Part 14, as shown in the
gure. Use one Part I and ve Parts E per Part H.
I
H
Ix 4 pcs. Hx 4 pcs.

-17-
Assembly Steps
STEP 19
STEP 20 Fix Part D2 on the back of the table, as shown in the gure. Connect
Part D1 and Part D2 with plastic straps.
Install Part D1 on the wall where you would like to place the table.
1
34
2
Dx 1 pc.
1
2
D1
D1
D1
D2
D2

-18-
Assembly Steps
STEP 21 The assembly is complete.
【LED Mirror Light】Touch the button on the mirror to turn the mirror light on
or o and to adjust the lighting. There are three lighting options: cold light,
natural light, and warm light. Long press the button on the mirror to adjust the
brightness. The versatile LED mirror lights can meet the dierent needs of users.

To continuously improve its products, VIVOHOME reserves the right to modify this
information without prior notication.
For any questions regarding assembly, please watch the video on the product page or
contact our customer service. Our customer service will gladly assist you with any
additional questions, comments, or concerns.
Thank you for using VIVOHOME products in your home!