LAZBOY Addyson Sling Swivel Rocker User manual

Addyson Sling Swivel Rocker
Owner’s Manual
If you have any problems with this product, DO NOT RETURN IT TO THE STORE.
CALL OUR CUSTOMER SERVICE HOTLINE AT
877-592-7514
Monday – Friday, 8AM-5PM (EST)
La-Z-Boy® is a registered trademark of La-Z-Boy Incorporated and is used under license to BJI,
Inc. © 2019 La-Z-Boy Incorporated.
Page 1 of 6

For warranty and other helpful information, please visit www.lazboyoutdoor.com or call 1-877-592-7514, Monday-Friday,
8AM-5PM (EST)or email us at [email protected].
Care and Maintenance
Be careful to never allow water to build up in frames as this will cause corrosion and freeze damage in cold climates. Wash all
frames with a solution of mild soap and water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be
treated with a liquid wax for maximum protection against UV rays and/or salty damp air. If your set includes cushions, slings,
and/or an umbrella they may be cleaned by hand with a solution of soap and water with a clean water rinse. (Never machine
wash cushions, slings or umbrella covers as this will result in shrinkage or damage).
After cleaning cushions tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry fabric goods).
Do not use bleach or solvents to clean any product! This will void the warranty.
Lack of original receipt will void warranty!
CAUTION: Read all the instructions before assembly. Failure to do so may result in faulty assembly and potential injury!
Assemble product on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging the item. Seek assistance to
assemble bulky or heavy items.After final alignment, make sure all bolts and nuts are securely tightened with screw head covers
pressed in place.
Note: Do not allow children to play with plastic wraps or small parts to prevent potential choking hazard.
Page 2 of 6

Right Arm Panel
Seat Panel
Back Panel
Base
Left Arm Panel
T-Rocker
Steel Plate
Bolt M6x30mm
Bolt M6x20mm
M6 Washer
M6 Plastic Cap
1
1
1
1
1
1
1
1
4
8
6
14
14
CC
DD
AA
BB
I
Front seat connect bar
seat connect bar
Page 3 of 6
PARTSNO. PARTS NAME PARTS QTY
PARTS LIST

Bolt M8x45mm
M8 Washer
Spring washer
M8 Plastic Cap
M6-M8 Wrench
M8 Plastic Cap
M8 Nut
4
10
4
4
6
4
2
GG
HH
II
JJ
KK
Step 2. Place the seat cushion (H) and lumbar pillow (I) on the chair. See Figure 2.
Page 4 of 6
EE
FF
PARTSNO. PARTS NAME PARTS QTY
Bolt M8x20mm 2
LL
PARTS LIST

Page 5 of 6
Step 1. Attach the back panel (D),seat panel (C) and front seat connect bar (E) to arm panel
(A) and (B) with bolts(AA)(BB) and washers (CC) by using wrench(LL), cover the bolts with
plastic caps (DD). See Figure 1.
Step 2. Turn over the chairDttach the FRQQHFWEDU)WRDUPSDQHO$%ZLWKEROWV%%
(FF)DQGZDVKHUV&&(GG)E\XVLQJZUHQFKLLFRYHUWKHEROWVZLWKSODVWLFFDSV''(JJ). 
&RQQHFWWKH75RFNer(H) WRWKHconnect bar (F)ZLWK steel plates (I),EROWV(( ZDVKHUV
GGVSULQJZDVKHUVHHDQGQXWVIIE\XVLQJZUHQFKLL7LJKWHQWKHEROWVFRPSOHWHO\
XQWLODOOEROWVDUHLQSODFH7KHQFRYHUWKHEROW (EE)ZLWK caps (JJ) and cover the nuts (II) with
caps (KK). See Figure 2.
Figure 1
Figure 2

Step 3. Turn the chair upright, put your hands on the arms and press the T-rocker
into the hole of chair base (G). See Figure 3.
Now your chair is ready for your enjoyment. See Figure 4.
Page 6 of 6
Figure 3
Figure 4
G