Vivo CART-V06A User manual

Sit and Stand Mobile Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-v06a
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: CART-V06A

2
PACKAGE CONTENTS
WARNING!
A (x19)
M5x12
B (x4)
M5x20
C (x9)
M6x12
E (x1)
4mm Allen Key
F (x1)
Wrench
G (x6)
M5x12 Flathead
1 (x1)
Desktop
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
2 (x2)
Shelf Bracket
3 (x1)
Support Plate
4(x1)
Keyboard Shelf
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
5 (x3)
Release Lever
Handle
6 (x1)
Base
33 lbs
(15 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 4.4 lbs
(2 kg)
DESKTOP TRAY
7 (x4)
Locking Caster
D (x6)
M6x15

3
ASSEMBLY STEPS
STEP 1
Screw casters (7) into underside of base. Tighten with wrench (F).
STEP 2
Assemble poles to base using x9 M6x12 screws (C) and x6 M6x15 screws (D), making sure the pole with
the release lever is installed in the center.

4
STEP 3
Install support plate (3) to poles using x6 M6x12 screws (C). Tighten with 4mm Allen wrench (E).
Assemble desktop (1) using x10 M5x12 screws (A). Secure release lever handle to desktop with x3
M5x12 screws (A).
STEP 4

5
STEP 5
Secure center pole to desktop (1) with x4 M5x20 screws (B).
Install keyboard shelf brackets (2) to desktop using x6 M5x12 screws (A). Curved slots must be facing
towards the front.
STEP 6

6
STEP 7
Mount keyboard shelf (4) to brackets with x6 M5x12 screws (G).
Ensure the handle is correctly pulling on the release cable. If the release cable tension is too high
(height will not lock) or too low (desk will not raise or lower), turn the nuts at the end of the black tube
near the handle to adjust the tension. Press the handle on each side up and down.
STEP 8

7
STEP 9
To adjust height, li release lever handle (5).

Last Updated: 04/16/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654