Vivo STAND-SIT1D User manual

Sit to Stand Single Monitor Desk Mount Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1d
SKU: STAND-SIT1D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x1)
Pole
C(x1)
Tray Pole
O(x1)
Holder
P(x1)
Top Cable Clip
N(x1)
Grommet
J (x1)
Support Plate
K (x1)
Decorative Cover
L (x1)
Clamp
M (x1)
Protective Pad
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Upper Tray
E(x1)
Lower Tray
F (x1)
Bumper
G(x1)
Mount
H (x1)
VESA Plate
I (x1)
Thumbscrew
R(x1)
Lower Cable Clip
Q(x2)
Bracket
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-D (x4)
M5x16
M-C (x4)
M5x12
M-B (x4)
M4x16
M-E (x4)
D5 Washer
M-F (x4)
Spacer
T (x3)
Flat Head Bolt
S(x15)
Bolt
U(x2)
Nut
W(x2)
Plastic Washer
V(x2)
Steel Washer
Y (x2)
Rubber Pad
X(x2)
Washer
Z(x1)
Wrench
B1 (x1)
6mm Allen Wrench
A1 (x1)
4mm Allen Wrench

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Loosen clamp bolts in clamp (L) using 6mm Allen wrench (B1). Slide decorative cover (K) onto pole
(B). Attach pole to clamp using flat head bolts (T) and tighten with 4mm Allen wrench (A1), then slide
decorative cover down onto clamp. Apply protective pad (M) to bottom of clamp base. Place support
plate (J) onto clamp bolts, place clamp with pole onto desk, and tighten clamp bolts evenly using
6mm Allen wrench. Attach cable management clip (R) to pole. If needed, change clamp height by
removing bolts from the back of the clamp, then reattach at alternate height.
OPTION B: Grommet Installation
Attach grommet base (N) to pole (B) using flat
head bolts (T) and tighten with 4mm Allen wrench
(A1). Cut end from protective pad (M), and apply
remaining circular pad to bottom of grommet
base. Remove one bolt from the clamp (L), then
use bolt with support plate (J) to secure base
with pole to desktop and tighten with 6mm Allen
wrench (B1). Attach cable management clip (R)
to pole.
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 4.4 lbs
(2 kg)
MOUNT TRAY
M
T
A1
K
B
B1
L
J
20-88mm
B1
R
A1
J
A1
10-50mm
1
2
3
M
B1
0mm-55mm
R
J
B1
A1
T
N

4
STEP 2
STEP 5
Place large washers (X) over screws on back of tray pole (C). Attach tray pole to mount on arm (A)
using nuts (U) with steel washers (V) and plastic washers (W) as shown in diagram, and tighten with
wrench (Z).
Slide arm (A) onto pole (B). Adjust stopper
height with 4mm allen wrench (A1).
STEP 3
Apply rubber pads (Y) to brackets (Q) as shown.
STEP 4
Attach upper tray (D) and brackets (Q) to tray
pole (C) using bolts (S) and tighten with 4mm
Allen wrench (A1).
A
A1
Y
Q
A1
S
D
C
X
Z
W
V
U
10mm

5
STEP 6
Attach lower tray (E) to plate on tray pole (C) using bolts (S) and 4mm Allen wrench (A1). Mount
release handle and cable management clip (P) to preferred side of tray using bolts (S) and 4mm Allen
wrench, then use the clip to secure the black tube.
OPTION A: Right Handed
Apply bumper (F) on le side if you use mouse
with your right hand.
STEP 8
STEP 7
Attach mount (G) to pole (C) using 4mm allen
wrench (A1). Clip on holder (O) to pole (C) as
shown.
OPTION B: Le Handed
Apply bumper (F) on right side if you use mouse
with your le hand.
A1
S
P
3
1
EP
SA1
2
O
G
A1
F

6
STEP 9
STEP 10
Slide monitor onto mount (G) and secure with thumbscrew (I). Tighten or loosen joints with allen
wrenches (A1,B1). Allen wrenches (A1,B1) can be stored in cable management clip on pole (C).
OPTION A: Flat Back Monitor
Attach VESA plate (H) to monitor. For flat back
monitors use screws (M-A or M-C) and washers
(M-E).
OPTION B: Curved Back Monitor
Attach VESA plate (H) to monitor. For curved
back monitors use screws (M-B or M-D),
washers (M-E), and spacers (M-F).
STEP 11
Adjust gas spring tension using the 6mm Allen wrench (B1). Turn counter-clockwise to increase li,
and clockwise to decrease. To adjust height of mount, li release handle, then raise or lower mount
to desired height. NOTE: use a large flat-blade screwdriver to tighten the socket set screw if the joint
makes a popping noise.
H
M- E M- A
M- C
H
M- B
M- D
M- E
M- F
B1
A1
2
1
I
3
A1
B1
ON
OFF
B1

7
Adjust as Desired
STEP 12
Loosen two screws holding cable cover to
arm, then slide cover forward to remove.
STEP 13
Insert cables into cover and reattach cover to arm.
1
2
3
2
1
+15°
-5°
±90 °
360 °
±90 °

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303