Vivo DESK-MB43TB User manual

Black 43” x 24” Manual Height Adjustable Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-mb43tb
SKU: DESK-MB43TB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
TOOLS NEEDED
Phillips
Screwdriver
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B (x1)
Leg
D (x1)
Crossbar Spacer
E (x2)
Side Bracket
S-A (x16)
M6x12 Bolt
S-C (x10)
ST4.2x20 Screw
C (x1)
Leg with
Gearbox
S-B (x4)
ST3.5x20 Screw
Drill
F (x1)
Sync Rod
H (x2)
Foot
G (x1)
Crank
S-D (x10)
Anti-Vibration
Pad
S-E (x1)
Allen Wrench
I (x1)
Le Desktop
J (x1)
Center Desktop
L (x2)
Support Pad
K (x1)
Right Desktop
M (x24)
Flat Head Screw
N (x4)
Desktop
Connector
121lbs
(55kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Tape Measure
Tape
Measure

3
STEP 2
Loosen the two set screws on the telescopic crossbar (A) using the Allen wrench (S-E) and partially
extend the crossbar.
ASSEMBLY STEPS
STEP 1
Assemble the desktops (I, J, K) using the desktop connectors (N) and flat head
screws (M). Tighten screws with a Phillips screwdriver.
STEP 3
Place the crossbar spacer (D) on the leg (B) as shown. Attach the telescopic crossbar to the legs (B,
C) as shown using M6x12mm bolts (S-A), and tighten with the Allen wrench (S-E). NOTE: Insert all
necessary screws into holes before tightening.

4
STEP 4
Attach the side brackets (E) to both ends of the frame using four M6x12mm bolts (S-A). Tighten with the
Allen wrench (S-E). NOTE: The top of each bracket must be facing inward for correct alignment of the
crank with the pre-drilled mounting holes.
STEP 5
Loosen the knob on the socket end of the sync rod (F) and slide the
sync rod onto the sha of the gearbox. Tighten the knob.
STEP 6
Loosen the knob on the other end of the sync rod and extend the hex sha into the socket in the
leg, making sure the sha is fully inserted with the red O-ring bumper spaced no more than 0.5”
from the leg.

5
STEP 7
Place the frame upside down on the desktop, extend to match the desktop mounting holes, then
tighten the set screws with the Allen wrench (S-F). Adjust the sync rod if needed, then tighten the
knob on the sync rod.
STEP 8
Insert the anti-vibration pads (S-D) into the desktop mounting holes in the crossbar and side brackets.
STEP 9
L
L
13.25”
L
L
Place the support pads (L) onto the crossbar in the locations shown below.
NOTE: The measurements shown will place the pads (L) beneath the seams of the desktop, which is
critical for ensuring the desktop panels are level.
13.25”

6
3
STEP 11
Loosen the set screw on the crank (G) using the Allen wrench (S-E). Extend the crank into the
gearbox, and with the front of the support plate flush with the front of the desktop, retighten the set
screw. Secure the support plate to the underside of the desk using ST3.5x20 screws (S-B).
STEP 10
Place the assembled frame on the desktop, making sure the holes are aligned with the desk frame, and
secure the frame using ST4.2x20 screws (S-C).

7
3
STEP 12
Place the feet (H) on the legs as shown. Insert and tighten bolts (S-A) using the Allen wrench (S-E).
STEP 13
Pull crank out when raising/lowering the desk height. Push back in
when not in use. If necessary, adjust foot pads to level the desk.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
CAUTION: When moving desk, ALWAYS carry the desk by
the frame part ONLY and never by the divided desktop.

LAST UPDATED: 08/06/2020
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303