Vivo DESK-V042KB-M2 User manual

Desk Riser with Dual Monitor Mount
Instruction Manual
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v000k-m2
SKU: DESK-V042KB-M2

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
33lbs
(15kg)
WARNING!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DESKTOP
4.4lbs
(2kg)
17.6lbs
(8kg)
KEYBOARD TRAY PER SCREEN
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING
PINCH POINT
DO NOT place hands on or near support bars. Moving parts can crush and
Failure to follow these instructions may result in serious personal injury.

3
PACKAGE CONTENTS
A (x1)
Desk
B(x1)
Keyboard Tray
S-A (x2)
ST4.2x12mm Screw
F (x2)
Cable Clip
G (x1)
Swivel Arm
H (x1)
Pole
I (x2)
VESA Plate
J (x1)
Grommet
Plate
K (x1)
Clamp
Bolt
L (x1)
Support Plate
M (x1)
Pole Cable
Clip
N (x4)
Arm Cable
Clip
O (x1)
Pole Cap
P (x5)
Rubber Pad
D (x3)
Pad
E (x4)
Rubber Feet
TOOLS NEEDED
Scissors Phillips
Screwdriver
C (x1)
Stopper
S-B (x4)
M5x10mm Screw
S-C (x2)
M3x8mm Screw
S-D (x2)
Knob
M-A (x8)
M4x12mm
Screw
M-B (x8)
M4x16mm
Screw
T-A (x1)
6mm Allen
Wrench
M-C (x8)
M5x12mm
Screw
M-D (x8)
M5x16mm
Screw
M-E (x8)
M5 Washer
M-F (x8)
Spacer

4
ASSEMBLY STEPS
STEP 1
STEP 2
Apply Pads (D) to underside of Keyboard Tray (B). Assemble Stopper (C) to Kayboard Tray (B) using
ST4.2x12mm Screws (S-A) and a Phillips screwdriver.
Install Rubber Feet (E) to the bottom of Desk (A). Remove shipping tie from desk and set right side up
on solid surface. NOTE: DO NOT squeeze the handle on Desk (A) while cutting the shipping tie.
B
S-A
E
A
D
C

5
Raise Desk (A) by liing the handle on the right side of the frame.
Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard Tray (B) to brackets
using M5x10mm Screws (S-B) and tighten with a Phillips screwdriver.
S-B
STEP 3
A
B
A

6
Remove the grommet cap from the top of the Desk (A).
Install the Pole Cap (O) onto the top of the Pole (H).
STEP 5
STEP 4
O
H
Grommet
Cap
Remove adhesive cover and install the Rubber Pads (P) onto the underside of the Grommet
Plate (J) in an even, circular pattern.
P
J
A

7
Place the Pole (H) onto the Grommet Plate (J). Slide Support Plate (L) onto Clamp Bolt (K), then
thread Bolt through mounting hole in Desk (A), anchoring into Pole with Grommet Plate.
STEP 6
STEP 7
Slide Pole Cable Clip (M) and Swivel Arm (G) onto Pole (H). Secure Swivel Arm in place using 6mm
Allen Wrench (T-A). Attach Arm Cable Clips (N) to Swivel Arm.
H
J
L
K
G
H
M
N
T-A

8
Recessed Back Monitor
Install VESA Plates (I) to monitors using appropriate Screws (M-B, M-D), M5 Washers (M-E),
Spacers (M-F) and a Phillips screwdriver, being careful not to overtighten.
STEP 8
Flat Back Monitors
For flat back monitors, install VESA Plates (I) to monitors using appropriate Screws (M-A, M-C),
M5 Washers (M-E) and a Phillips screwdriver, being careful not to overtighten.
I
M-E
M-A
M-C
I
M-B
M-D
M-E
M-E

9
Adjust monitor tilt by using the 6mm Allen Wrench (T-A) to loosen and tighten the joint.
STEP 9
Slide monitors onto Swivel Arm (G). Place Knobs (S-D) on VESA Plates (I) and secure using M3x8
Screws (S-C) and a Phillips screwdriver.
STEP 9
S-D
I
S-C
T-A

10
Apply Cable Clips (F) to underside of Desk (A) and route cables.
F
A
Manage cables using Arm Cable Clips (N) and Pole Cable Clip (M).
STEP 10
M
N