Vivo DESK-GME2B User manual

Black 47” Electric Gaming Desk with LED Lights
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-gme2b
SKU: DESK-GME2B
[email protected]om www.vivo-us.com 309-278-5303

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
PACKAGE CONTENTS
A (x24)
M5x16
B (x8)
M6x16
C (x10)
M5x10
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
E (x1)
4mm Allen
Wrench
D (x5)
Cable Clip 1 (x2)
Desktop
2 (x1)
Control Panel
3 (x1)
Power Cord
4 (x1)
Control Unit
5 (x1)
Extension
Cable
6 (x1)
Support
Frame
7 (x1)
Side Bracket
8 (x1)
Side Bracket
9 (x2)
Leg
10 (x4)
Plastic Cover
11 (x2)
Foot
12 (x2)
Desktop
Connecting Plate
13 (x1)
Power
Adapter
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK. PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Level 220lbs
(100kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
STEP 2
Assemble side brackets (7, 8) to
support frame using M6x16 bolts (B),
making sure the long crossbar is in the
center of the brackets, and tighten with
the Allen wrench (E).
Insert legs (9) into support frame (6), making
sure the pre-installed bolts are fit into the slots.
Insert two M6x16 bolts (B) into each side to
secure the legs, and tighten all bolts using the
4mm Allen wrench (E).

4
STEP 3
STEP 4
Assemble feet (11) to legs using M5x10 bolts (C), making sure both feet are facing
forward, and tighten with the Allen wrench. Snap plastic covers (10) onto the short ends
of the feet.
Assemble the desktop (1) using desktop connecting plates (12) with M5x16 screws (A)
and tighten with a Phillips screwdriver.

5
STEP 5
Place assembled frame on the desktop and secure using ten M5x16 screws (A). Four screws
fit each side bracket, and two screws fit the support frame between the legs. Secure control
unit (4) and control panel (2) using two M5x16 screws for each. Tighten all screws with a
Phillips screwdriver.
Connect control panel, legs, extension cable (5) and power cord (3) to control unit and
manage cables using cable clips (D).
STEP 6
Turn the desk right side up and connect the power adapter (13) to the desktop lighting
cable.

6
OPERATING INSTRUCTIONS: When the system is powered on, the
existing desktop height will appear on the control panel.
Upward and Downward Movement
Press and hold the up or down arrow until
the desk reaches the desired height.
Memory Mode
To store a certain height in the controller’s memory, first press “M”. The current height will begin flashing
on the display. Now press “1”, “2”, “3” or “4” within six seconds to store the current height in memory.
Each number can store a dierent height. Once in memory, you can recall any of the four height settings
by pressing the corresponding button. Touching any button will stop the automatic adjustment.
Power-Saving Mode
When no actions are made for over 2 minutes, the system will enter power-saving mode. Touch any
button to enter operating mode.
Function Mode
Press and hold the “M” button for 3 seconds, or until “S - -” begins flashing on the display. Press “M”
again to enter Function mode. Within function mode, use the up and down buttons to scroll through
settings, and use the “M” button to select options. If no action is taken for 20 seconds, the desk will return
to operating mode.
• Change Displayed Unit (Un): Press the up or down buttons until the display shows “Un”, and press
“M” to select. Press up or down to select “SI” (metric) or “In” (imperial). Hold “M” for 2 seconds to
save the setting.
• Change Brightness (br): Press the up or down buttons until the display shows “br”, and press “M”
to select. Press up or down to select Low (L), Normal (n) or High (H) brightness. Hold “M” for 2
seconds to save the setting.
• Collision Force Detection (CF): Press the up or down buttons until the display shows “CF”, and
press “M” to select. Press up or down to select “OFF”, Low (L), Normal (n) or Heavy (H) collision force
detection. Hold “M” for 2 seconds to save the setting.
STEP 7
3
Plug the power cable into an AC wall outlet, then use the control panel to adjust the height.
OPERATING CONTROL PANEL

7
3
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
NOTES
• Self-protection function: The unit will enter a protective mode should the system operate
continuously in excess of 2 minutes with “HOT” on the controller display. The system will
return to normal operation aer approximately 18 minutes.
• Do NOT remove or reconnect power to reset the unit when in a protective or “HOT” state, as
this may damage the electronics.
TROUBLESHOOTING
Error Code Description/Resolution
HOT Heat Warning: Allow desk to rest for 18 minutes.
E10 Motor connection fault: Disconnect desk power, disconnect the motor, reconnect the
motor, then reconnect power.
E20 Desk overload: Unplug desk for 10 seconds then reconnect to power.
E02 Obstacle protection. Desk will automatically move back 4cm aer collision.
E31 Under-voltage (power brown out). Will clear automatically when line power is corrected.
E32 Over-voltage (power surge). Will clear automatically when line power is corrected.
E60 Legs are at dierent heights. Reset the desk to align the legs.
Reset Mode
While the unit is powered on, press the down arrow until the desk moves to the fully lowered position.
Press and hold the down arrow for 5 seconds or until “rES” is displayed to enter reset mode. The desk
will move down to the lowest possible height and then move back up slightly. The desk will then return
to operating mode.
• E20 - Desk Overload: If overloaded while moving up, error will clear aer 3 seconds. If overloaded
moving down, unplug desk for 10 seconds then reconnect power.
• Circuit Protection: If motor or controller becomes disconnected, the desk will cease operation.
Error will clear aer all components are reconnected.

LAST UPDATED: 12/11/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M