Vivo DESK-EW43TW User manual

White 43" x 24" Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-ew43tw
SKU: DESK-EW43TW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B x1)
Motorized Leg
C(x1)
Leg
D(x1)
Crossbar
Spacer
E(x2)
Side Bracket
F(x1)
Sync Rod
G (x2)
Foot
H x1)
Adapter Holder
I(x1)
AC Adapter
J(x1)
Power Cable
K(x1)
Controller
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x16)
M6x12
S-B x10)
ST4.2x20 Screw
S-C (x2 )
ST3.5x20 Screw
S-D (x3)
Cable Clip
S-E (x10)
Anti-Vibration
Pad
S-F (x1)
Allen
Wrench
L (x1)
Le Desktop
M x1)
Center Desktop
N(x1)
Right Desktop
O(x2)
Support Pad
P(x24)
Flat Head
Screw
Q(x4)
Desktop
Connector

3
ASSEMBLY STEPS
STEP 1
Assemble the desktops (L, M, N) using the desktop connectors (Q) and flat head
screws (P). Tighten screws with a Phillips screwdriver.
STEP 2
Loosen the two set screws on the telescopic crossbar (A) using the Allen wrench (S-F) and partially
extend the crossbar.
STEP 3
Place the crossbar spacer (D) on the motorized leg (B) as shown. Attach the telescopic crossbar to the
legs (B, C) as shown using M6x12mm bolts (S-A), and tighten with the Allen wrench (S-F). NOTE: Insert
all necessary screws into holes before tightening.
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
143lbs
(65kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Tape Measure
Tape
Measure

4
STEP 4
Attach the side brackets (E) to both ends of the frame using four M6x12mm bolts (S-A). Tighten with
the Allen wrench (S-F).
Loosen the knob on the other end of the sync rod and extend the hex sha into the socket in the leg,
making sure the sha is fully inserted with the red O-ring bumper spaced no more than 0.5” from the
leg. Tighten the knob.
STEP 5
Loosen the knob on the socket end of the sync rod (F) and slide the
sync rod onto the sha of the motorized leg. Tighten the knob.
STEP 6

5
STEP 7
Place the feet (G) on the legs as shown. Insert and tighten bolts (S-A) using the Allen wrench (S-F).
STEP 8
STEP 9
Place the adapter holder (H) over the telescopic crossbar and tighten the two thumbscrews. Place the
AC adapter (I) into the adapter holder (H).
Place the frame upside down on the desktop, extend to match the desktop mounting holes, then
tighten the set screws with the Allen wrench (S-F).

6
STEP 10
Connect the AC adapter and motorized leg to the controller (K).
Connect the power cable (J) to the AC adapter.
STEP 11
Insert the anti-vibration pads (S-E) into the desktop mounting holes in the crossbar and side brackets.
STEP 12
Place the support pads (O) onto the crossbar in the locations shown below.
NOTE: The measurements shown will place the pads (O) beneath the seams of the
desktop, which is critical for ensuring the desktop panels are level.
13.25”
OO
O
13.25”

7
STEP 14
Attach the controller to the underside of the desktop using ST3.5x20 screws (S-C) as shown. Once the
controller is installed, cable clips (S-D) can be attached to the desk for cable management. Refer to the
Controller User Guide for operational instructions.
STEP 13
Place the assembled frame on the desktop, making sure the holes are aligned with the desk frame, and
secure the frame using ST4.2x20 screws (S-B).
STEP 15
If necessary, adjust foot pads to level the desk.
CAUTION: When moving desk, ALWAYS carry the desk by
the frame part ONLY and never by the divided desktop.

Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
LAST UPDATED: 08/06/2020
REV2
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.