Vivo DESK-V201B/G/P User manual

Kids’ Height Adjustable
Desk and Chair
Instruction Manual
SKU: DESK-V201B/G/P
Assembly Video & Product Info
https://vivo-us.com/products/desk-v201b

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please
contact our product support team at 309-278-5303 or [email protected] for further assistance. Check carefully to
make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: PINCH POINT
DO NOT PLACE HANDS ON OR NEAR SUPPORT BARS. MOVING PARTS CAN CRUSH AND CUT.
PINCH POINTS ARE CREATED DURING LIFTING AND
LOWERING THE WORK SURFACE. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY.

3
A (x1)
Chair Leg
B(x4)
Foot
S-A (x8)
M6 Lock Washer
S-B (x14)
M6x20mm Screw
S-C (x12)
Plastic Washer
S-D (x4)
ST4.8x25mm Screw
S-E (x4)
M6x12mm Screw
S-F (x4)
M6x40mm Screw
T-A (x1)
4mm Allen Wrench
I (x1)
Drawer
J (x1)
Desk Leg
K (x1)
Right Rail
L (x2)
Le Rail
M (x2)
Hook
F (x1)
Seat Bottom
G (x1)
Seat Back
H (x1)
Desktop
D (x1)
Le Support
E (x1)
Straight
Support
Desk Chair
C (x1)
Right Support
Package Contents
Included Hardware & Tools
Weight Capacity:
165lbs
(75kg)
220lbs
(100kg)
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:
Phillips
Screwdriver
Tools Needed:

4
CHAIR ASSEMBLY STEPS
STEP 1
Place Chair Leg (A) into Feet (B).
Secure Feet to Chair Leg using M6x20mm Screws (S-B), Metal Lock Washers (S-A), and 4mm Allen
Wrench (T-A).
A
B
S-A (x4)
S-B (x4)
T-A
S-B
T-A
S-A

5
STEP 2
Secure the Right Support (C) uptop the right side of Chair Leg (A) using M6x20mm Screws (S-B), Plastic
Washers (S-C), and 4mm Allen Wrench (T-A).
Slide Straight Support (E) into Le and Right Support (C,D). Then secure Le Support Tube to
Chair Leg (A) using M6x20mm Screws (S-B), Plastic Washers (S-C), and 4mm Allen Wrench (T-A).
Assembly Note:
Vertical Section of Right Support should
overhang the long portion of Foot.
Washers should be
installed with flat
end facing down.
C
A
S-B
S-C (x2)
S-B (x2)
S-C
T-A
D
C
S-C (x2)
S-B (x2)
T-A
T-A
E
S-B
S-C
T-A

6
STEP 3
Place Seat Bottom (F) over Right and Le Supports (C,D). Secure using ST4.8x25mm Screws (S-D) and
a Phillips screwdriver.
Slide the Seat Back (G) onto the Right and Le Supports (C,D).
S-D (x4)
S-D
G
DC
C
D

7
STEP 4
Secure the Seat Back (G) to the Right and Le Supports (C,D) using M6x20mm Screws (S-B)
and 4mm Allen Wrench (T-A). If needed, chair can be leveled using pads on Feet (B).
S-B (x2)
T-A
C
B
G
D
S-B

8
DESK ASSEMBLY STEPS
STEP 1
STEP 2
Press Desk Legs (J) into Feet (B), making sure legs are fully seated in openings. Secure Feet (B) using
M6x20mm Screws (S-B) and Metal Lock Washers (S-A). Tighten with 4mm Allen Wrench (T-A).
Assemble Le Drawer Slider (K) and Right Drawer Slider (L) to Desktop (F) using M6x12mm
Screws (S-E) and Plastic Washers (S-C). Tighten with 4mm Allen Wrench (T-A).
S-B (x4)
T-A
S-A (x4)
J
T-A
S-B
S-A
B
Washers should be
installed with flat
end facing down.
S-E
F
J
L
T-A
S-C (x4)
T-A
S-E (x4)

9
STEP 3
Loosen the knobs on Desktop (F) to li the top, then tighten the knobs to secure it in place.
Press Hook (K) onto Desktop (F) support making sure it is facing out from the desk. Secure
Desktop (F) to Desk Legs (H) using M6x40mm Screws (S-F), Plastic Washer (S-C) and 4mm Allen
Wrench (T-A).
F
Washers should be
installed with flat
end facing down.
S-C (x4)
M
H
F
S-F
T-A
T-A
S-E (x4)

10
STEP 4
STEP 5
Extend both slides on Drawer (G) and simultaneously slide them inside of previously installed Le and
Right Drawer Sliders (K,L).
Level desk by adjusting pads on underside of Feet (B).
G
K
L
B

11
To adjust the chair or desk height, remove the 4 pre-installed screws on Chair and Desk Legs (A,J) using
the 4mm Allen Wrench (T-A). Reinstall screws at desired height.
ADJUSTING CHAIR & DESK HEIGHT
J
A
T-A
12.59-15.74”
21.25-29.92”
320-400mm
540-760mm

LAST UPDATED: 10/24/2023
REV2L
v3.4
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us