Vivo DESK-E-100W User manual

White Electric Single Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e-100b
SKU: DESK-E-100W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
H (x16)
ST4.8x16
I (x2)
ST2.9x15
O (x1)
Power Cord
M (x1)
Controller
N (x1)
AC Adapter
P (x6)
Cable Clip
S (x1)
2mm Allen
Wrench
T (x1)
5mm Allen
Wrench
A (x1)
Telescopic
Cross Bar Set
B x1)
Motorized Leg
C x1)
Non-motorized
Leg
D(x2)
Side Brackets
E (x2)
Foot
J x4)
M6x8
L x8)
M6x30
K x12)
M6x10
Q (x2)
Screw-on
Eyelet
R (x2)
10" Ziptie
F (x1)
Sync Rod
Center Sha
G (x2)
Sync Rod Hex
Sha

3
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosely assemble the Telescopic Cross Bar Set (A) making sure the locking holes are facing up as
shown below. Partially insert M6x8 bolts (J) into the locking holes using Allen Wrench (T), making sure
the Cross Bar is still able to slide freely.
TOOLS NEEDED
Phillips
Screwdriver Drill Tape
Measure
J
A

4
STEP 2
Attach Cross Bar (A) to both the Motorized Leg (B) and Non-motorized Leg (C) using M6x10 bolts (K),
making sure the locking bolts are still facing up on the Cross Bar. Tighten with Allen Wrench (T).
STEP 3
Attach Side Brackets (D) to both ends of the frame using M6x10 bolts (K). Tighten with Allen Wrench (T).
A
B
C
K
D
K

5
STEP 4
Place a foot (E) on each leg as shown below. Attach each foot using M6x30 bolt (L). Tighten with Allen
Wrench (T).
STEP 5
STEP 6
Insert one of the Sync Rod Hex Shas (G) through the motor and into the Motorized Leg (B).
NOTE: If the hex does not line up with the leg, temporarily plug the Motorized Leg (B) and the AC Adapter
(N) into the Controller (M) (see step 10 for details). Then, while pushing on the hex sha, very briefly
press the up and down arrows (alternating between the two buttons so the legs will still be even when
assembled) until the sha slides into the leg.
FOR VIVO DESKTOP: Adjust frame width until the Side Bracket (D) holes line up with the pre-drilled
holes on the desktop. Adjust center crossbar section until all M6x8 bolts (J) are able to make contact,
then fully tighten using Allen Wrench (T). To attach the desktop, refer to the manual included with your
desktop. Set aside x2 of the ST4.8x16 screws (H) for mounting the AC Adapter (N).
FOR OTHER DESKTOP: Adjust the frame to the desired width while making sure the overhang does
not exceed 10" on either side. Adjust center crossbar section until all M6x8 bolts (J) are able to make
contact, then fully tighten using Allen Wrench (T). Mark and drill pilot holes to a depth of 3/8" (10mm)
using a 1/8" (3mm) bit where the Side Brackets (D) align on the desktop. Secure the frame using
ST4.8x16 screws (H) to the desktop. Set aside x2 of the ST4.8x16 screws (H) for mounting the AC
Adapter (N).
E
L
J
D
H
G
B

6
Center the Sync Rod Center Sha (F) so it rest's evenly on both Sync Rod Hex Shas (G). When in place,
tighten the preinstalled set screws using the smaller Allen Wrench (S).
Note: Be sure not to pull out the hex shas from either leg.
STEP 8
Loosen the preinstalled set screws on the Sync Rod Center Sha (F) using Allen Wrench (S). Slide the
Sync Rod Center Sha (F) onto the installed motor Sync Rod Hex Sha (G) as far as it will go. Then install
the second Sync Rod Hex Sha (G) into the Sync Rod Center Sha (F). Then slide the second Hex Sha
into the Non-motorized Leg (C).
NOTE: If the hex does not line up with the leg, temporarily plug the motorized leg (B) and the AC
Adapter (N) into the Controller (M) (see step 10 for details). Then, while pushing on the sha, very briefly
press the up and down arrows (alternating between the two buttons so the legs will still be even when
assembled) until the sha slides into the leg.
STEP 7
Attach the Controller (M) to the desktop using ST2.9x15 screws (I), making sure it is on the side of the
Motorized Leg (B).
STEP 9
F
F
G
C
F
SET SCREWS
G
G
B
I
M
GG

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
STEP 11
If necessary, adjust foot pads at the bottom of foot (E) to level the desk.
STEP 10
Plug cables together as shown below. Tidy up cables using Cable Clips (P). Attach AC Adapter (N) to
desktop using ST4.8x16 screws (H), the Screw-on Eyelets (Q), and 10" Zipties (R) as shown below.
Note: A desk reset is required before use. Refer to the Controller User Guide for operational
instructions. Ensure there is enough slack in the cables at the lowest and highest positions before use.
EE
N
M
O
P
Q
R
N
H
2.75"
(70mm)

LAST UPDATED: 03/08/2022
REV3.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303