Vivo DESK-V000K-M2 User manual

Black Desk Riser with Dual Monitor Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v000k-m2
SKU: DESK-V000K-M2
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
Pole
C(x2)
VESA Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole Cable
Clip
E(x4)
Arm Cable
Clip
F (x1)
Pole Cap
G(x2)
M3x8
H (x2)
Knob
J (x1)
Hand Bolt
M-A (x8)
M4x12
M-B (x8)
M4x16
M-D (x8)
M5x16
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
I (x1)
Stand Base
K (x1)
Support Plate
L(x4)
Rubber Pad
N (x1)
Desk
P (x2)
Cable Clip
O (x1)
Keyboard Tray
Q (x3)
Pad
R(x4)
Sleeve Nut with
Bolt
S (x4)
Rubber Foot
M (x1)
6mm Allen
Wrench
M-C (x8)
M5x12
M-E (x8)
D5 Washer
M-F (x8)
Spacer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
PER SCREEN
Separate the sleeve nut w/ bolt (R) into R1 and R2.
Apply pads (Q) to underside of keyboard tray. Press R1 into holes on top of keyboard tray (O).
33lbs
(15kg)
DESKTOP
4.4lbs
(2kg)
KEYBOARD TRAY
STEP 3
Install the rubber feet (S) to the base of the desk. Cut the large plastic tie beneath desk (N).
N
S
E
B
Bottom
B
C1
Top
P
NNQ1
Q
Q
O
OR1

4
STEP 4
STEP 5
Raise the desk by squeezing the handles underneath the desk.
Place keyboard tray (O) on metal brackets on
desk (N). Secure keyboard tray to brackets
using screws (R2) and tighten with a Phillips
screwdriver.
STEP 6
Apply cable clips (P) to underside of desk.
STEP 7
Attach pole cap (F) to the top of the pole (B).
P

5
STEP 8
STEP 9
Apply rubber pads (L) to underside of stand base. Remove plug from desk surface (N).
Position the pole (B) with stand base
(I) over the grommet hole, and install
to desktop using the hand bolt (J) with
support plate (K).
STEP 10
Slide pole cable clip (D) and arm (A) down onto pole (B) to the desired
height and tighten with the 6mm Allen wrench (M). Attach the arm cable
clips (E) to the arms.
STEP 11
OPTION A: Flat Back Monitor
Install the VESA plates (C) to monitors using bolts (M-A or
M-C) and washers (M-E).

6
STEP 11 (Continued)
STEP 12
Slide the VESA plates (C) with monitors onto the arms (A). Secure using the knobs (H) with
M3x8 bolts (G).
STEP 13
If needed, adjust tilt joint support using the 6mm Allen wrench (M).
OPTION B: Curved / Recessed Back Monitor
Install the VESA plates (C) to monitors using bolts (M-B or
M-D), washers (M-E) and spacers (M-F).
M

7
STEP 14
Use the cable clips (D, E) to organize cables.
STEP 15
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
STEP 16
Adjust desk height by squeezing the
handle and pulling up or pushing
down. Adjust monitor position and
rotation as desired. Adjust monitor
alignment by turning the knob (H)
over each VESA plate (C). Store the
Allen wrench (M) in the pole cable clip
(D) when not in use.

LAST UPDATED: 06/07/2021
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303