Vivo CART-V03E User manual

Black Multi-Purpose Mobile Podium
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/cart-v03e
SKU: CART-V03E
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
1 (x2)
Long Square
Tube
2 (x2)
Short Square
Tube
3 (x4)
Caster
4 (x1)
Tube Connector
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF CART.
• USE TIPOVER RESTRAINT OR ANCHOR CART TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
5 (x1)
Tube Connector
Cover
6 (x4)
M6 Socket Plate
7 (x2)
Pole Set
8 (x4)
Plastic Sleeve
9 (x1)
Connecting
Tube
10 (x2)
Plastic Knob
11 (x2)
Shelf Support
12 (x1)
Shelf
13 (x1)
Top Plate
14 (x1)
Right Connecting
Plate
15 (x1)
Le Connecting
Plate
16 (x4)
M6 Nut
17 (x2)
Lever
18 (x2)
So Pad
19 (x8)
M6x60
20 (x12)
M6x10
21 (x4)
M4x6
22 (x2)
M5x6 Set Screw
23 (x2)
M6 Washer
24 (x1)
Tool Kit

3
ASSEMBLY STEPS
STEP 2
Attach Plastic Sleeves (8) to Pole Set (7) as
shown. Slide the inner poles upward with
the plastic sleeves fitting inside the outer
poles, then extend the innser poles upward
until both shelf support holes are visible.
STEP 3
Attach the Long Square Tube (1) to the front of the
Tube Connector (4) and the Short Square Tube (2)
to the back of the Tube Connector (4) using M6x60
Screws (19) and the M6 Socket Plate (6). Tighten
using the provided Allen Wrench (24).
STEP 1
Attach Casters (3) to the Short and Long Square
Tubes (1, 2) using the provided Wrench (24).
19
4
Front
7
8
44 lbs
(20 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 22 lbs
(10kg)
TOP SHELF BOTTOM SHELF
3
1
3
2
24
24
Back
6
1
2
Shelf
Support
Holes
TOOLS NEEDED
Phillips
Screwdriver

4
STEP 4
Mount the Connecting Tube (9) to the Pole Set (7) using M6x10 Screws (20) using the provided Allen
Wrench (24).
STEP 5
Aer making sure the poles are at the same height, insert Plastic Knobs (10) into the back of the Pole
Set (7) to set the height of the Inner Poles.
STEP 6
Slide the Connector Cover (5) over the Pole Set (7). Attach the Pole Set (7) to the Tube Connector (4)
using M6x10 Screws (20) in the back and M5x6 Set Screws (22) in the sides. Tighten using the provided
Allen Wrenches (24).
10
7
5
Left
Right
Front
Shelf
Support
Holes
4
7
Front
Front
20
24
24
22
920
24
7

5
STEP 7
Attach the Shelf Supports (11) to the Pole Set (7) using M6x10
Screws (20). Tighten using the provided Allen Wrench (24).
STEP 8
Mount the Right and Le Connecting Plates (14, 15) to the Top Plate (13) using M6 Nuts (16) and
tighten with the provided Wrench (24). The slots in the connecting plates must be facing towards the
front.
STEP 9
Attach the Shelf (12) to the Shelf Supports (11) using M4x6 Screws (21). Tighten with a Phillips
screwdriver.
12
21
13
16
15
14
24
11
20
20
7
11
24
Front

6
18
STEP 10
Place the assembled Top Plate (13) onto the Pole Set (7), and secure with M6x10 Screws (20).
STEP 11
Attach So Pads (18) to the top front edge of the Top Plate (13).
STEP 12
Insert Levers (17) with M6 Washers (23) through the slots in the Connecting Plates (14,15) and screw
into Pole Set (7).
17 23
20
713
7
14
15
13

7
STEP 13
Loosen the Levers (17) to adjust the tilt angle, then tighten in the desired position. Adjust the height by
loosening the Plastic Knobs (10), then tighten at the desired height.
STEP 14
tilt 40˚
10
17

LAST UPDATED: 05/10/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303