Vivo MOUNT-G200B2 User manual

Dual Monitor Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-g200b2
SKU: MOUNT-G200B2
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Mount
W-A (x3)
ST6.3x55mm Screw
M-A (x8)
M4x12mm Screw
M-B (x8)
M5x12mm Screw
M-C (x8)
D5 Washer
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x3)
M6 Washer
W-B (x3)
Concrete Anchor
T-A (x1)
4mm Allen Wrench
B (x1)
VESA Plate
C (x1)
Handle
D (x2)
VESA Bracket
E (x1)
Bracket
F (x2)
Arm
G (x1)
Bracket Cover
H (x2)
End Cap
I (x2)
Cable Clip
J (x1)
Upper Cover
K (x1)
Lower Cover
T-B (x1)
6mm Allen Wrench
T-C (x1)
Wrench
S-A (x4)
M6x30mm Screw
S-B (x2)
M5x10mm Screw
S-C (x4)
M5x16mm Screw
S-D (x4)
M5 Washer

3
TOOLS NEEDED
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR CEILING CONSTRUCTION. USE WOOD STUDS
TO MOUNT. We include mounting for concrete ceilings as well. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
ASSEMBLY STEPS
STEP 1 (Option A)
Wood Stud Installation
Hold Mount (A) in place along the stud and mark mounting holes using a pencil. Using a 3/16”
(4.5mm) drill bit, drill holes in marked locations approximately 2.2” (55mm) deep. Secure Mount (A) to
the wall using ST6.3x55mm Screw (W-A) with M6 Washers (W-C) and a Phillips screwdriver.
Pencil
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Studfinder
PER SCREEN
A
W-A
W-C

4
STEP 1 (Option B)
Concrete/Brick Wall Installation
Hold Mount (A) to mounting surface and mark drill holes with pencil. Drill 2.4” (60mm) deep holes using
a 3/8” (10mm) drill bit. Insert Anchors (W-B) into predrilled holes and secure Mount (A) to the wall using
ST6.3x55mm Screw (W-A) with M6 Washers (W-C) and a Phillips screwdriver.
STEP 2
Insert Upper Cover (J) and Lower Cover (K) into the mounting holes on Mount (A).
A
W-B
W-A
W-C
J
K
A

5
STEP 3
Remove the nut from the bottom of VESA Plate (B) using Wrench (T-C) and loosen the top two nuts,
leaving 3mm of threads exposed.
STEP 4
Assemble Arms (F) to Bracket (E) with Bracket Cover (G) using M6x30mm Screws (S-A) and 4mm Allen
Wrench (T-A).
B
T-C
F
E
G
S-A
T-A

6
STEP 5
Slide VESA Brackets (D) onto Arms (F). Insert End Caps (H) into the ends of Arms (F). Secure
End Caps (H) using M5x10mm Screws (S-B) and a Phillips screwdriver. Lock VESA Brackets
(D) in place using 4mm Allen Wrench (T-A). Assemble Cable Clips (I) to Arms (F).
D
F
H
S-B
T-A
I

7
STEP 6
Slide VESA Plate (B) onto Mount (A) and tighten the top two nuts using Wrench (T-C).
Insert the bottom nut onto VESA Plate (B) and tighten with Wrench (T-C).
Assemble Bracket (E) to VESA Plate (B) and Handle (C) using M5x16mm Screws (S-C) and
M5 Washers (S-D) with a Phillips screwdriver.
STEP 7
E
B
C
S-C
S-D
B
A
T-C

8
STEP 8
STEP 9
Insert Screws (M-A or M-B) with D5 Washers (M-C) into the top two holes of your monitor,
leaving 3mm of space. Slide the monitors onto VESA Brackets (D) and insert Screws (M-A or
M-B) with D5 Washers (M-C) into the bottom holes of your monitor. Tighten all screws with a
Phillips screwdriver.
Adjust the tilt on VESA Brackets (D) using 6mm Allen Wrench (T-B).
D
D
T-B

9
STEP 10
Level the monitors by adjusting the nuts on VESA Plate (B) using Wrench (T-C).
T-C
B

10
STEP 11
Adjust the tension in Mount (A) using 6mm Allen Wrench (T-B). Rotate clockwise to decrease
tension, and counter clockwise to increase tension.
A
T-B