Vivo STAND-MIC03L User manual

Black Low Height Microphone Desk Mount
Instruction Manual
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-mic03l
SKU: STAND-MIC03L

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
PACKAGE CONTENTS
4.4lbs
(2kg)
ASSEMBLY STEPS
STEP 1 - Option A - Clamp Installation
Loosen knob on Clamp (C). Mount Clamp (C) to Arm Base (D) using M5x12mm Screws (S-A) and
3mm Allen Wrench (T-A).
WARNING!
A (x1)
Upper Arm
B (x1)
Lower Arm
C (x1)
Clamp
D (x1)
Arm Base
E (x1)
Grommet Plate
F (x1)
So Pad
S-A (x3)
M5x12mm Screw
TOOLS NEEDED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Phillips
Screwdriver
T-A (x1)
3mm Allen Wrench
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
C
S-A
T-A
D

3
STEP 1 - Option A - Continued
STEP 1 - Option B - Grommet Mount
Apply So Pad (F) to inside of Clamp (C).
Secure assembly to desktop by tightening knob on Clamp (C).
Unscrew Clamp Screw (C1) on Clamp (C). Disassemble Clamp (C) using a Phillips screwdriver and
remove Clamp Screw (C1) and Clamp Plate (C2). Set remaining components aside. Slide Clamp Plate
(C2) to the bottom of the Clamp Screw (C1) and set aside for use in next step.
Proceed to Step 2 on Page 5
C
F
C
C1
C1
C2
C

4
STEP 1 - Option B - Grommet Mount
Mount Grommet Plate (E) to Arm Base (D) using M5x12mm Screws (S-A) and 3mm Allen Wrench
(T-A), making sure the tapered holes are facing away from the Arm Base. Remove adhesive backing
from So Pad (F) and adhere to Grommet Plate (E).
If you do not have an existing grommet hole, use a 3/8” (10mm) drill bit to drill through desktop
surface to create a gromment openning.
Secure assembly to desk using Clamp Screw (C1) and Clamp Plate (C2).
Proceed to Step 2 on Page 5
T-A
S-A
F
D
E
C1
C2

5
STEP 2
STEP 3
Loosen the set screw on the Arm Base (D), using 3mm Allen Wrench (T-A) then install Lower Mic
Arm (B). Tighten set screw using 3mm Allen Wrench (T-A).
Loosen the set screw on the Lower Mic Arm (B) using 3mm Allen Wrench (T-A), then install Upper
Mic Arm (A). Tighten set screw using using 3mm Allen Wrench (T-A).
B
D
Loosen Set
Screw
Tighten Set
Screw
T-A
A
T-A
T-A
B
Loosen Set
Screw
Tighten Set
Screw

6
Step 4
Detach cable management trays from mic arms by sliding them towards the front of the mic stand.
Run mic cable under the mic arms and reattach cable management trays.

7
Adjust as Desired
To adjust mic angle, loosen the knob and set as desired. Re-tighten knob when set.
Loosen Joint Screw on Upper Arm (A) using 3mm Allen Wrench (T-A) to adjust arm to desired height.
T-A
A

LAST UPDATED: 05/04/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303