Vivo STAND-V102O User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102o
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V102O

2 3
ASSEMBLY STEPS
STEP 1
OPTION A: Desk Clamp Install
Assemble base (B) to clamp (C)
using M6x8 bolts (F), and tighten
with 5mm Allen key (H). Unscrew
the large clamp bolts to the “open”
position.
For 3/8” - 2” (10mm - 50mm) desk
thickness, place clamp disks (E)
onto the top of the clamp bolts.
Place assembled base onto edge
of desk and tighten using the 5mm
Allen key.
For 1-1/2” - 3-1/8” (40mm - 80mm)
desk thickness, remove the two
bolts from the back of the clamp
using 5mm Allen key, and then
reassemble clamp to the lower
position. Place clamp disks (E)
onto the top of the clamp bolts.
Place assembled base onto edge
of desk and tighten using the 5mm
Allen key.
PACKAGE CONTENTS
TOOLS NEEDED
14.3lbs
(6.49kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x2)
Arm
B(x1)
Base
C(x1)
Clamp
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x1)
Support Plate
E(x2)
Clamp Disk
F (x2)
M6x8 Bolt
G(x1)
3mm Allen Key
H (x1)
5mm Allen Key
OPTION B: Grommet Base Install
Remove large clamp bolts from clamp (C).
If necessary, drill two holes in desk using a
3/8” (10mm) drill bit. The support plate (D)
may be used as a drill guide. Secure base
(B) to desk using clamp bolts with support
plate (D), and tighten using 5mm Allen key
(H). NOTE: Grommet option will fit a desk
thickness of 3/8” - 1-3/4” (10mm - 45mm).
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
PER SCREEN
Do not overtighten screw!
Do not overtighten screw!

4 5
STEP 2
While holding arm (A) in the closed position, cut the shipping tie from each arm.
STEP 4
STEP 5
STEP 3
Place the arms (A) onto the base (B). Tighten the screw on the back of each arm using the
3mm Allen key (G) or a flat blade screwdriver.
Attach two bolts (M-A or M-B) and washers (M-C) to top
mounting holes of each monitor, making sure to leave
1/8” (3mm) of threads exposed.
Align bolts installed to monitor with VESA plate. Secure using two more
bolts (M-A or M-B) and washers (M-C) in the bottom two holes. Tighten all
four bolts using the 5mm Allen key (H) or a Phillips screwdriver. Repeat for
second monitor.
1. Firmly hold the two halves of the spring arm together and
have another person cut o the cable tie from around the
spring arm.
2. Slowly release the pressure on the spring ar and allow it
to gradually stretch to it’s full extension.

6 7
STEP 6 STEP 7
Use cable clips on arms (A) to organize cables.
Adjust gas spring tension in arms (A) and monitor bracket tilt support using 5mm Allen
key (H). Turn gas spring tension adjustment screw counter-clockwise to increase support,
and clockwise to decrease support.

Last Updated: 04/03/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654