Vivo DESK-V102E User manual

Black Electric Single Motor Desk Frame
Follow along step-by-step with our video walk through by scanning
the QR code with your mobile device or by following the product
link: vivo-us.com/products/desk-v102e
Instruction Manual
SKU: DESK-V102E
ASSEMBLY VIDEO AVAILABLE:
[email protected]om www.vivo-us.com 309-278-5303

2
Contact Us First!
PERSONABLE CUSTOMER SUPPORT
Our friendly product support team is here to help!
DO NOT RETURN ITEM
We’re Here for You!
Missing a Part?
Our customer-minded support team is here for YOU,
Monday-Friday 7am-7pm CST.
We oer immediate assistance with rapid response times
from customer service agents and product techncians to
help you every step of the way!
Monday-Friday
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om
If any parts are received damaged / defective OR you are
missing a part, please reach out to us within 30 days of
product delivery to have it replaced at no cost.
We are happy to replace parts to ensure you have a fully
functioning product
7AM - 7PM

3
If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a qualified
technician. Check carefully to make sure there are no missing
or defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
PRE-ASSEMBLY | BEFORE YOU BEGIN
Product Warranty
Returns | Product Didn’t Work Out?
For the most up to date details on your product’s warranty, please visit
the product’s listing on our website or reach out to customer support.
vivo-us.com/products/desk-v102e
We oer a hassle-free 30 day return on all products. Contact customer
support at 309-278-5303 or [email protected]om. Please note: For items
ordered in error or no longer needed, the return shipping charges will
be at the buyer’s expense.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP
PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART
OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK
OF TIPOVER.
TIPOVER WARNING
WEIGHT CAPACITY
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
176lbs
(80kg)
!

4
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
A (x1)
Crossbar
B(x1)
Motorized
Leg
C(x1)
Leg
I (x1)
Shelf
J (x2)
Hook
H(x1)
Controller
D (x2)
Side Bracket
E (x1)
Sync Rod
F (x2)
Foot
G (x1)
Power
Adapter
S-F (x5)
ST3.5x13
Screw
S-E (x4)
M6x50mm Hex
Head Screw
S-A (x4)
M4x4mm
Screw
S-B (x4)
M5x14mm
Screw
S-D (x8)
M6x16mm Hex
Head Screw
S-C (x2)
M6x25mm Hex
Head Screw
T-A (x1)
4mm Allen
Wrench
S-G (x9)
ST4.2x16Screw
S-H (x9)
Anti-Vibration
Pad
Please consult the parts list below and ensure you have everything you need to assemble
your product. If parts are missing or damaged, please contact us.
Phillips Screwdriver
|
TOOLS NEEDED:
DIFFICULTY LEVEL
K (x1)
Power Cable
L (x3)
Cable Clip
Drill
|
Level
|

5
STEP 1: Attaching the Crossbar
Loosen set screw on Crossbar (A) to adjust length and re-tighten. Attach Crossbar (A) to Motorized Leg (B)
with M6x50mm Screws (S-E) and M6x25mm Screws (S-C), as shown below.
Have a question? Give us a quick call / chat!
309-278-5303 or vivo-us.com
ASSEMBLY STEPS
T-A
A
Crossbar
B
Motorized Leg
C
Leg
S-E
M6x50mmScrew
S-C
M6x25mm Screw
T-A
4mm Allen Wrench

6
STEP 2: Attaching Side Brackets
Attach Side Brackets (D) to Motorized Leg (B) and Leg (C) using M5x14mm Screws (S-B) using 4mm Allen
Wrench (T-A).
STEP 3: Apply Anti-Vibration Pads
Apply Anti-Vibration Pads (S-H) to top of Side Brackets (D), as shown below.
T-A
D
D
Side Bracket
S-B
M5x14mm Screw
S-B
S-H
Anti-Vibration Pad
T-A
4mm Allen Wrench
D

7
STEP 4: Installing Desk Feet
STEP 5: Adjusting Frame Width to Desktop
Flip desk frame over and attach Foot (F) to bottom of Motorized Leg (B) and Leg (C) using M6x16mm Screws
(S-D) and 4mm Allen Wrench (T-A).
Place intended desktop (not provided) upside down onto of a so surface and then place desk frame
assembly upside down on desktop. Adjust frame width to size of desktop, ensuring the that frace is centered
on the desktop.
Have a question? Give us a quick call / chat!
309-278-5303 or vivo-us.com
T-A
F
Foot
S-D
M6x16mm Screw
T-A
4mm Allen Wrench

8
STEP 6: Installing the Sync Rod
STEP 7: Installing the AC Adapter
Loosen the knobs on the Sync Rod (E) and extend the hex sha. Insert hex sha into the Leg (C), making sure
the metal retaining ring makes contact with the Leg. While holding the hex sha with one hand, extend sync
rod onto the spline sha of Motorized Leg (B). Retighten knob. Tighten set screw on Crossbar (A) to secure
frame width.
Attach Hooks (J) to Shelf (I) using M4x4mm Screws (S-A) with a Phillips screwdriver. Hang Cable
Management Tray (I) onto the Crossbar (A) and tighten knobs to secure. Place Power Adapter (G) into Cable
Management Tray.
E
Sync Rod
I
Cable Managemnet
Tray
J
Hook
G
Power Adapter
B
B
Leg with Motor
C
C
Leg
1 2 3 4
T-A
4mm Allen Wrench
S-A
M4x4mm Screw

9
STEP 8: Connect Frame to Desktop
Use ST4.2x16 Screw (S-G) to secure desk frame to desktop with a drill.
Have a question? Give us a quick call / chat!
309-278-5303 or vivo-us.com
S-G
ST4.2x16Screw

10
STEP 9: Connecting the Controller
Connect cords from Controller (H) to cord from Motorized Leg (B) and Power Adapter (G). Connect
Power Cable (K) to Power Adapter (G).
K
H(x1)
Controller
K (x1)
Power Cable
B
G