Vivo STAND-V003J User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003j
SKU: STAND-V003J
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x3)
VESA Plate
B(x1)
Monitor Arm
C(x1)
Base Cover
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Base
E(x1)
Leg
F (x1)
Leg
G (x1)
Pole
H (x2)
Pole Cap
I (x6)
M6x10
J(x3)
M6x16
K(x1)
Pad
L (x3)
Thumb Screw
M (x1)
4mm Allen
Wrench
N (x1)
6mm Allen
Wrench
O(x2)
Joint Cover
P(x4)
Cable Clip
M-A (x12)
M4x12
M-B (x12)
M5x12
M-C (x12)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
Assemble legs (E, F) to base (D) using M6x10 bolts (I), and tighten with the 4mm Allen wrench (M).
Apply pad (K) to front-center position underneath the base.
ASSEMBLY STEPS
STEP 1
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER MONITOR
TOOLS NEEDED
Phillips
Screwdriver

4
STEP 2
Press the base cover (C) onto the base.
Assemble the pole (G) to the base using
M6x16 bolts (J) and tighten with the 4mm
Allen wrench (M).
STEP 3
Slide the monitor arm (B) onto the pole to the
desired height, and tighten the center bracket
to the pole using the 6mm Allen wrench (N).
Attach cable clips (P) to arms.

5
STEP 4
Install the VESA plates (A) to monitors using M4x12 bolts (M-A) or M5x12 bolts
(M-B) with washers (M-C).
STEP 5
Slide VESA plates with monitors onto brackets on arm and secure using thumb screws
(L). Tighten or loosen the tilt joints using the 6mm Allen wrench (N).

6
STEP 6
Manage cables using the clips on the arms, then feed cables down through the pole and out the back.
Place pole covers (H) on top of pole, and joint covers (O) on arm joints.

7
STEP 7
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
STEP 8
Adjust monitor position and rotation as desired. To adjust monitor alignment, turn the top bolt
behind each bracket using the 6mm Allen wrench (N).

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303