Vivo STAND-V155C User manual

  
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
 (x1)
VES Plate
 (x1)
Pole
 (x1)
Pole Cap
 (x1)
Clamp
 (x1)
Cable Clip
 (x1)
Decorative Cover
(x1)
Grommet Base
Plate
! (x5)
Rubber Pad
" (x1)
Grommet Plate
# (x1)
3mm lle Wre ch
$ (x1)
4mm lle Wre ch
% (x2)
rm
 (x2)
rm
& (x2)
Bolt
 (x2)
Nut
 (x8)
Screw
' (x1)
Wre ch
-  (x4)
M6x30
-   (x4)
M8x30
-  (x4)
M5x14
-   (x4)
M6x14
- (x4)
D8
-  ! (x8)
Spacer
-  (x4)
M8x50
-   (x4)
D5
- -()**++ ,-*)* +
-  " (x8)
Spacer

-./ )
2
) 
) 0
&)  12 -) "
Slide cable management clip (E) and decorative cover (F) onto pole
(B). Then thread pole (B) into base of clamp (D). Tighten grub screws
with allen wrench (J) as shown in diagram. Slide decorative cover (F)
down. Apply rubber pads (H) as shown in diagram. Secure clamp (D)
to desk.
Place pole cap (C) onto pole (B).
) 0 34
&)  --  "
Remove screw and plate from clamp (D) as shown in diagram. Apply
rubber pads (H) to the bottom of grommet base (G) as shown in
diagram. Slide cable management clip (E) and decorative cover (F)
onto pole (B). Then thread pole (B) into grommet base (G). Tighten
grub screws with allen wrench (J) as shown in diagram. Slide
decorative cover (F) down. Slide grommet plate (I) onto hand crank.
Insert hand crank through grommet hole from bottom and into
grommet base (G).
10 - 80mm

0
) 5 34
&)  +  
) 
Attach VESA plate
(A) to back of TV
using screws (M-C,
M-D, M-E), washers
(M-G), and spacers
(M-H, M-I)
depending on your
TV's requirements
as shown in
diagrams. Make
sure the two
keyholes on back
have the small end
facing up.
Insert bolts (O) into pole (B) at desired height, making sure there are
3 holes unused between bolts. Thread nuts (P) onto bolts leaving
3mm of thread exposed behind bolt heads. Hang VESA plate (A) with
TV onto bolts, and tighten with 4mm Allen wrench (K) and wrench
(Q).
) 6
) 5
&)    
If installing a TV with a VESA
300x300mm or 400x400mm
pattern, attach arm (L, M) to
VESA plate (A) with screws (N)
as shown in diagram.
Attach VESA plate (A) to back of TV with screws (M-A, M-B) and
washers (M-F, M-G). Make sure the two keyholes on back have the
small end facing up.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
7/ 8
  
Last updated: 06/13/18
) 9
) :
Store allen wrenches (J, K) in cable clip (E) as
shown in diagram.
Manage cables using cable clip (E). Adjust tilt
and swivel of TV.
4