Vivo MOUNT-RAIL02W User manual

White Clamp and Rail Set for Custom Wood Tray
- 2 Pack
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-rail02w
SKU: MOUNT-RAIL02W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Assemble the slider brackets (A) to the clamps (B) using M4x7 screws (C). Tighten with a
Phillips screwdriver.
PACKAGE CONTENTS
WARNING!
Phillips
Screwdriver
A (x2)
Slider Track
B(x2)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
Drill
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
C(x6)
M4x7
D(x8)
ST5x12
E (x2)
Clamp Pad
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Pencil
NOT INCLUDED
A
B
CC
TOOLS NEEDED
LeRight
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED.
NOTE: Rails (A) and Clamps (B) should be paired with the corresponding "L" and "R" stickers.

3
STEP 2
Place the slider rails (A) on the underside of the keyboard tray, making sure the front of the rails are
flush with the front edge of the keyboard tray, and mark drilling locations. Drill 3/8” (10mm) deep
holes using a 1/8” (3mm) drill bit, then mount the slider rails to the keyboard tray using ST5x12
screws (D). Tighten with a Phillips screwdriver.
NOTE: We recommend using a tray with a depth of no less than 10.5”, and a thickness of at least 5/8”.
STEP 3
Place the clamp pads (E) on the underside of each clamp (B) as shown. Place assembled keyboard
mount on edge of desk and tighten clamps.
NOTE: To ensure keyboard tray is level, do not over-tighten clamps.
Slide keyboard tray forward/back to desired position.
D
D
E
Le
Right
NOTE: Rails (A) and Clamps (B) should be paired with the corresponding "L" and "R" stickers.

LAST UPDATED: 01/18/2022
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303