Vivo STAND-V001BL User manual

   
 
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
- -!""## $%"" #&
- (x4)
D5
-  (x4)
M4x12
-   (x4)
M5x12
 (x1)
Monito Stand
 (x1)
Clam Suot
(x1)
Clam
 (x1)
Cabl Cli
' (x1)
Bolt
( (x1)
Gommt Bas
) (x1)
Knob
 (x5)
Scw
* (x1)
Gommt Plat
+ (x1)
4mm lln
Wnch
, (x1)
5mm lln
Wnch
 (x1)
Tay
 (x4)
Rubb Pads
- (x4)
M5 Scw
 (x4)
D5 Wash
 (x1)
Sta
. (x4)
M4 Nut

%&/ 
2
 
-  0 1 % *
-  )%%  *
Slide bolt (E) through grommet base (F). Attach grommet base (F) to monitor stand
(A) with screws (H) using 4mm allen wrench (J). Secure to desk with grommet plate (I)
and knob (G).
Attach clamp
support (B) onto
base of monitor
stand (A) with screws
(H) using 4mm allen
wrench (J). Attach
clamp (C) to clamp
support (B) at
desired depth with
screws (H) using
4mm allen wrench
(J). Attach cable
management clip (D)
to clamp support (B).
Secure to desk.
 2
Insert screws (M-A or M-B) with washers (M-C) into top 2 holes on back of monitor.
Leave slightly loosened. Slide monitor onto VESA plate. Insert screws (M-A or M-B)
with washers (M-C) into bottom 2 holes of VESA plate into the monitor. Tighten all
screws using mm allen wrench (K).

Insert cables. Replace
covers making sure
the cables have
enough slack to allow
free movement of the
arm.
 3
 4 5  
 6
Adjust arm tension by turning bolt with mm Allen Wrench (K). Clockwise reduces
tension, counterclockwise increases tension. The tension should be just enough to
hold your monitor in place without lifting itself up. If needed, adjust the bolts on the
sides of the hinge behind the VESA plate to tighten or loosen the tilt angle.
 7
Remove cable covers
from upper and lower
arms. To remove lower
cover, remove the screw
as shown, pull slightly
forward, up and off.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
8/ 9
  
Last updated: 0 /24/18 4
 :
Attach tray (L) to VESA plate with M screws (O), washers (P), and nuts (Q). Insert
strap (N) as shown in diagram. Apply rubber pads (M) as shown in diagram.
 ;
Secure laptop to tray (L) with strap (N).