Vivo STAND-V006 User manual

Hex Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v006
SKU: STAND-V006
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
a (x1)
Pole
b(x1)
Clamp
c(x2)
Arm Assembly
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x24)
M4x12
e (x24)
M4x30
f (x48)
M4 Washer
g (x24)
M4 Spacer
h (x4)
M8x10
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
i (x2)
M10x15
j(x1)
Allen Key
k(x2)
Spare Plastic Cover
l (x1)
Wrench

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
Attach pole (a) to clamp (b) at desired height with screws (i) and Allen wrench (j). Secure clamp to
desk.
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4
STEP 2
Attach arm assembly (c) to the pole (a) with screws (h) at desired height, making sure the cable clips
are facing down. Repeat for second arm assembly.

5
STEP 3
OPTION A: Flat Back Monitor
Mount monitors to VESA plates using thumbscrews (d) and washers (f). Do not overtighten;
thumbscrews only need to be finger-tight.
OPTION B: Curved Back Monitor
For curved back monitors use screws (e), washers (f), and spacers (g).

6
STEP 4
Manage cables using the cable clips. Cables on top arm assembly can be passed through the top of the
pole and out the rear cable hole below.
To adjust swivel joint tension, remove the plastic cover and turn the bolt underneath with the Allen
key (j).

7
STEP 5
To adjust tilt support, remove the plastic cover and turn the nut underneath with the wrench (l).
Turn the bolt counterclockwise to lower the center monitor, turn the bolt clockwise to raise the center
monitor.

LAST UPDATED: 04/24/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303