Vivo STAND-V038/W User manual

Dual Ultrawide Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v038
SKU: STAND-V038/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR
OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
22 lbs
Per Arm
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

3
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
D (x2)
VESA Plate
S-A (x3)
M6x16mm Screw
S-B (x2)
M6 Security
Nut
M-A (x8)
M4x12mm
Thumbscrew
E (x1)
Grommet
Base Plate
F (x1)
So Pad
G(x1)
Support
Plate
H (x1)
Pole Cap
I (x1)
Pole Cable
Clip
J(x4)
Arm Cable
Clip
M-B (x8)
M4x30mm Screw
M-C (x8)
M6 Spacer
T-A (x1)
3mm Allen
Wrench
T-B (x1)
6mm Allen
Wrench
TOOLS NEEDED
Phillips Screwdriver

4
ASSEMBLY STEPS
STEP 1
*** IMPORTANT NOTE ***
Monitor mount can be assembled as a Desk Clamp (2a) or Grommet Mount (2b).
Follow steps below for desired mounting method.
STEP 2a - Desk Clamp
B
Loosen knob on Clamp (B).
B
A
S-A
T-A
Mount Clamp (B) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
Secure assembly to desktop by tightening knob on Clamp (B).
Proceed to Step 3
on page 6

5
STEP 2b - Grommet Mount
Using a Phillips screwdriver,
remove the screw from Clamp (B)
and disassemble. Set Knob (B2)
aside.
Mount Grommet Plate (E) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen
Wrench (T-A). Remove adhesive backing from So Pad (F) and adhere to
Grommet Plate (E).
Secure assembly to gromment hole in desk using Knob (B2) and Support Plate (G), as
shown below.
If there is not an exisiting grommet
hole, use a 3/8” (10mm) drill bit to
drill through desktop surface.
B
B2
E
S-A
B
B2
T-A
A
F
B2
G

6
STEP 3
Unfold Swivel Arm (C) and extend into one straight line.
Attach Arm Cable Clips (J) to Swivel Arm (C).
C
H
C
I
A
T-B
Slide Pole Cable Clip (I) and Swivel Arm (C) onto Pole (A). Secure Swivel Arm (C) in place
using 6mm Allen Wrench (T-B). Attach Pole Cap (H) to Pole (A).
C
J

7
STEP 4
Secure VESA Plates (D) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm
Screws (M-B). M6 Spacers (M-C) may be required.
D
D

8
STEP 6
Manage cables using Arm Cable Clips (J) and Pole Cable Clip (I).
STEP 5
Slide monitors with VESA Plates (D) onto Swivel Arm (C). Secure VESA
Plates (D) in place using M6 Security Nuts (S-B).
D
S-B
C
J
I

9
ADJUST AS DESIRED
+90° to -90° TILT:
If monitors are sagging or need repositioned, loosen the bolt on the side of the VESA
Head (C1) on Swivel Arm (C). Use 6mm Allen Wrench (T-B) to loosen, then adjust. Tighten
to secure. .
180° SWIVEL:
Lighten pull monitors le or right to adjust swivel.
360° ROTATION:
Lighten pull monitors le or right to adjust swivel.
T-B

10
ADJUST MONITOR HEIGHT
To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws
using 3mm Allen Wrench (T-A). Once level, fasten M6 Security Nuts (S-B) back into place.
T-A
S-B