Vivo STAND-V104B User manual

Quad Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v104b
SKU: STAND-V104B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Arm
B(x4)
VESA Plate
D(x1)
Base
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
E(x1)
Lower Pole
F (x1)
Upper Pole
I (x2)
Cable Clip
J (x4)
Thumbscrew
K (x3)
M6x12
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x16)
M4x16
M-C (x16)
M5x12
L (x1)
3mm Allen
Wrench
M(x1)
4mm Allen
Wrench
STEP 1
M-D (x2)
M5x16
Attach the pole cap (G) to the top of the upper pole (F).
M-E (x16)
D5 Washer
M-F (x16)
Spacer
N(x1)
5mm Allen
Wrench
O (x1)
6mm Allen
Wrench
M-A (x16)
M4x12
C (x1)
Bracket
H (x1)
Pole
Connector
G (x1)
Pole Cap
Drill
15.4lbs
(7kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
STEP 2
Mount the lower pole (E) to the base (D) using M6x12 bolts (K) with the 4mm Allen wrench (M).
STEP 3
Install the arm (A) and one cable clip (I) to the lower pole (E). Fasten the bolt with the 5mm Allen
wrench (N).

4 5
STEP 7
Slide the VESA plates (B) with monitors onto the heads of the arms (B) and bracket (C).
Install the thumb screws (J) to secure the monitors.
STEP 4
Screw the pole connector (H) down onto the lower pole (E), then screw the upper pole (F) into the
pole connector (Note: pole connector set screws may need to be loosened first). Tighten the set
screws in the pole connector using the 3mm Allen wrench (L).
OPTION A: Flat Back Monitor
Install the VESA plates (B) to the monitors using bolts (M-A or M-C) and washers (M-E).
STEP 5
Install the bracket (C) and second cable clip (I) to the upper pole (F). Fasten the bolt with the 6mm
Allen wrench (O).
STEP 6
OPTION B: Curved/Recessed Back Monitor
Install the VESA plates (B) to monitors using bolts (M-B or M-D), washers (M-E) and spacers
(M-F).
STEP 6 (Continued)

6 7
STEP 8
Tighten or loosen the tilt joints using the 6mm Allen wrench (O).
STEP 9
Manage cables using the installed cable clips (I).
STEP 10
Store the Allen wrenches in the cable clips
(I) for future use.
STEP 11
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
STEP 12
Adjust monitor alignment using 5mm Allen wrench (N).

LAST UPDATED: 03/20/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303