Vivo STAND-V100HU User manual

Pneumatic Arm Single Ultra Wide Monitor
Desk Mount with USB
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v100hu
SKU: STAND-V100HU
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
39.6lbs
(18kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
A (x1)
Base
B(x1)
Arm
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
T (x1)
4mm Allen
Wrench
S (x1)
Wrench
U (x1)
6mm Allen
Wrench
TOOLS NEEDED
Phillips
Screwdriver
C(x1)
Rear Cover
D(x1)
Clamp Brace
E(x1)
Grommet
Base Plate
F (x1)
Clamp Plate
G(x1)
Clamp Bracket
H (x2)
Clamp Bolt
I (x1)
VESA 200x100
Plate
K (x2)
Carriage Bolt
O (x4)
M4x12
L (x2)
Support Plate
M (x2)
D8 Washer
N (x2)
M8 Nut
P (x4)
M6x12
Q (x4)
D4 Washer
R (x4)
M4 Nut
J (x1)
VESA Plate

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (D) to base (A) using M6x12 bolts (P), and tighten with 4mm Allen wrench
(T). Insert clamp bolts (H) into clamp bracket (G) as shown, then place clamp plate (F) on top of
assembled clamp. Install clamp (G) to upper holes of clamp brace (D) for a desk thickness of 3/8”
to 1-1/2” (10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 - 84mm). Place
assembled base on edge of desk and tighten clamp bolts evenly with 6mm Allen wrench (U).
OPTION B: Grommet Installation
Place carriage bolts (K) into square holes in grommet base plate (E). Attach grommet base plate to
base (A) using M6x12 bolts (P), and tighten with 4mm Allen wrench (T). Place assembled base over
cable grommet hole in desktop, and tighten using support plates (L), D8 washers (M) and M8 nuts (N),
and tighten with wrench (S). If a grommet hole isn’t present, drill two 3/8” (10mm) holes 49mm apart
through the desktop.

4
STEP 3
OPTION A: VESA 75x75, 100x100
Install the VESA plate (J) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers
(M-C), making sure the rounded edges of the rear bracket are facing up.
OPTION B: VESA 200x100
Install the VESA 200x100 plate (I) to the VESA plate (J) using the M4x12 bolts (O) with D4 washers (Q)
and M4 nuts (R), tightening with the wrench (S) and a Phillips screwdriver. Mount assembled VESA
plate to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers (M-C), making sure the
rounded edges of the rear bracket are facing up.
STEP 2
Insert the arm (B) into the socket of the base,
then secure using the 4mm Allen wrench (T) or
a flat-blade screwdriver. Install rear cover (C) to
clamp brace if the clamp option was used.

5
STEP 4
STEP 5
Pull back the latch on the support bracket at the end
of the arm (B), then place the monitor with VESA
plate onto the support bracket.
While holding the arm in the horizontal position, adjust the gas spring tension
using the 6mm Allen wrench (U).

6
STEP 6
STEP 7
Remove cable covers from base and adjustable arm. Organize cables and reinstall cable covers to
base and adjustable arm.
Tighten or loosen the tilt joint using the 6mm Allen wrench (U).

7
STEP 8
Adjust the monitor position as desired. Plug USB cables into USB ports on the computer.

LAST UPDATED: 07/23/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303