Vivo STAND-V101H User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101h
SKU: STAND-V101H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Monitor Arm
B(x1)
Clamp
C(x1)
Clamp Brace
T-C (x1)
6mm Allen Wrench
M-A (x4)
M4x12mm Screw
M-D (x4)
M5x16mm Screw
T-B (x1)
4mm Allen Wrench
J (x5)
Rubber Pad
S-A (x2)
M6x10mm Screw
S-B (x1)
Thumbscrew
T-A (x1)
3mm Allen Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
M-F (x4)
Spacer
M-E (x4)
M5 Washer
D(x1)
Grommet Base
E(x1)
Pole
F (x1)
Base Cover
G(x1)
VESA Plate
H (x1)
Support Plate
I (x1)
Cable Clip
M-C (x4)
M5x12mm Screw
M-B (x4)
M4x16mm Screw
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
FOR VESA ADAPTER:
K (x1)
Adapter Plate
S-C (x4)
M4x12mm Screw
S-E (x8)
M5 Washer
S-D (x4)
M4 Nut

3
ASSEMBLY STEPS
TOOLS NEEDED
4-26.4lbs
(1.81-11.97kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver Wrench
STEP 1
F
E
STEP 2
J
Stick Rubber Pads (J) to the underside of Clamp
Brace (C). (Skip to Step 3 Option B if grommet
base option will be used)
Slide Base Cover (F) onto Pole (E).
STEP 3 (Option A)
Clamp Installation
Assemble Clamp (B) to Clamp Brace
(C) using M6x8mm Screws (S-A)
and tighten with 4mm Allen Wrench
(T-B). Thread Pole (E) onto Clamp
Brace (C), and tighten pre-installed
set screws with 3mm Allen Wrench
(T-A). Press Base Cover (F) into
place. Place assembly on the edge
of the desk and tighten the hand
bolt to secure.
10-88m m
C
C
S-A
T-B
E
T-A
F

4
STEP 3 (Option B)
STEP 4
Grommet Base Installation
Thread Pole (E) onto Grommet Base (D), tighten pre-installed set screws with 3mm Allen Wrench
(T-A), and press Base Cover (F) into place. Stick Rubber Pads (J) to the underside of Grommet Base (D).
Remove screw from end of Hand Bolt (B1) on Clamp (B) and separate parts. Use Hand Bolt (B1) with
Support Plate (H) to secure base assembly to grommet hole in desk.
10-85mm
Slide Cable Clip (I) and Monitor Arm (A) onto Pole (E). Secure Monitor Arm (A) using 6mm Allen
Wrench (T-C).
E
F
D
T-A
J
B
B1
H
IA
E
T-C

5
OPTION A: Flat Back Monitor
For at back monitors, install VESA Plate
(G) to monitor using Screws (M-A) or
(M-C) and M5 Washers (M-E).
OPTION B: Curved Back Monitor
For curved back monitors, install VESA
Plate (G) to monitor using Screws (M-B)
or (M-D), M5 Washers (M-E), and Spacers
(M-F).
STEP 5
TV
TV
TV TV
GM- E
M- A
M- C
M- E
M- B
M- D
M- F
FOR VESA ADAPTER:
If your monitor has a 200x100 VESA hole pattern, install Adapter Plate (K) to VESA Plate (G) using
M4x12mm Screws (S-C), M4 Nuts (S-D), and M5 Washers (S-E). Install Adapter Plate (A) to the monitor
using Screws (M-A through M-D) and M5 Washers (M-E).
M-A through M-D
M-E
KG
S-C
S-D
S-E

6
STEP 6
Slide VESA Plate (G) over bracket on Monitor Arm (A). Secure using Thumbscrew (S-B).
L
STEP 7
Remove bottom cover from Monitor Arm (A) by sliding cover
forward and o.
STEP 8
Run cables through bottom of Monitor Arm (A). Reattach cover.
G
S-B
A
A
A

7
STEP 9
Adjust tension in Monitor Arm (A) and angle of monitor using 6mm Allen Wrench (T-C). Clockwise
reduces tension, counterclockwise increases tension. The tension should be just enough to hold your
monitor in place without liing itself up.
STEP 10
Adjust monitor to desired position and store Allen Wrenches (T-A, T-B, T-C) in Cable Clip (I) for future
adjustments.
T-C
T-C
A
+35°
-35°
±180°
±115°
±180°
±90°
T-A
T-B
T-C
I

LAST UPDATED: 08/18/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303