Vivo MOUNT-PC01C User manual

Black Under Desk Leg Clamp PC Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pc01c
SKU: MOUNT-PC01C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
S-A (x4)
M5x6mm Screw
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
4mm Allen
Wrench
B (x1)
Mount
C (x12)
Pad
T-A (x1)
4mm Allen Wrench

3
ASSEMBLY STEPS
STEP 1
Apply Pads (C) to top, bottom, and side of Mount (B) as shown.
STEP 2
Loosen the sets screws on the either side of Mount (B) using 4mm Allen Wrench (T-A) to adjust the
height.
C
B
B
T-A

4
STEP 3
Insert M5x6mm Screws (S-A) into Clamp (A) leaving a 2mm gap.
STEP 4
Insert the heads of M5x6mm Screws (S-A) with Clamp (A) into the slots in Mount (B).
Slots
S-A
A
S-A
A
B

5
STEP 5
Secure Clamp (A) to Mount (B) using M5x6mm Screws (S-A) in the lower holes. Tighten all screws using
a Phillips screwdriver.
STEP 6
Remove the protective film from Clamp (A) and assemble Clamp (A) to the desk leg by tightening both
knobs.
A
B
S-A
A

6
STEP 7
Loosen two screws on top of Mount (B) and slide side support bracket out to maximum width.
STEP 8
Place PC tower in Mount (B), slide bottom support up until Mount (B) is fit vertically to PC, and tighten
set screws using 4mm Allen Wrench (T-A). Slide the side bracket into place to hold PC, and tighten
screws using a Phillips screwdriver.
B
B
T-A

7
STEP 9
The PC mount is now ready for use.

LAST UPDATED: 05/24/2022
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303