Vivo STAND-V001L User manual

Laptop Tray and Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001l
SKU: STAND-V001L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Clamp
C(x1)
Clamp Brace
I(x1)
M10 Washer
L1 (x1)
Wire Clip
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M(x1)
Allen
Wrench Set
L2 (x2)
Wire Clip
D(x1)
Swivel Arm
E(x1)
VESA Plate
F (x3)
M5x14
G(x2)
M8x12
H (x1)
Nut
K (x1)
Grommet
Base Plate
J(x1)
Spring Washer
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
O(x4)
M4x30
P (x4)
M4 Spacer
N (x4)
M4x12 Thumb
Bolt
Q(x1)
Laptop Tray
R(x4)
M4x10
S(x4)
M4 Nut
T1 (x1)
So Pad
T2 (x1)
So Pad

3
ASSEMBLY STEPS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (T1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen key (M). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
Option B: Grommet Install
1. If desk does not have an existing grommet
hole, drill a 3/8” (10mm) diameter hole
at the desired position through the
mounting surface.
2. Completely disassemble clamp (B) into
individual parts. Set knob (B1) and
clamp plate (B2) aside for later use. The
L bracket, bolt, washer and bushing will
not be used.
3. Install grommet base plate (K) to the pole
(A) using x3 M5x14 bolts (F). See Figure 4.
4. Attach so pad (T2) to the grommet base
plate (K), see Figure 5.
5. Position pole (A) on the mounting surface
and secure using the clamp plate (B2),
spring washer (J), M10 washer (I) and
knob (B1). See Figure 6.
a
Figure 1 Figure 2
T1
F
C
A
M
G
B
B1
B2 a
m
f
Figure 4
t2 Figure 5
a
m
f
Figure 4
t2 Figure 5
J
B2
I
T2
K
B1
Wrench
F
A

4
STEP 2
Install swivel arm (D) to the pole (A). Fasten the bolt with supplied Allen key (M). Attach the wire clip
(L1, L2) to the pole (A) and swivel arm (D).
D
L2
ML1
STEP 3
OPTION A: Laptop
Attach the VESA plate (E) to laptop tray (Q) with M4x10 bolts (R) and M4 nuts (S).
Q
R
S
E

5
STEP 3 (Continued)
OPTION B: Flat Back Monitor
Attach the VESA plate (E) to the monitor with M4x12 thumb bolts (N).
NOTE: Hand tighten screws to avoid over tightening.
N
E
OPTION C: Curved Back Monitor
Attach the VESA plate (E) to the monitor with M4x30 bolts (O) and M4 spacers (P).
NOTE: Gently tighten with a screwdriver.
P
O
E

6
STEP 4
Slide the laptop tray/monitor onto the head of
swivel arm (D) as shown in the above diagram.
STEP 5
Tighten the bolt with the supplied Allen wrench (M) to fix the tilt angle.
Install the security nut (H). Make sure the security
nut is installed before you rotate the laptop tray/
monitor.
H
M

7
STEP 6
Manage cables using wire clips (L1,L2) and store Allen keys (M) in wire clip (L1) for future use.
o
STEP 5 (continued)
Use the supplied Allen key set (M) to make any necessary adjustments.
M
L1
L2

LAST UPDATED: 09/17/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303