Vivo STAND-V200F User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v200f
SKU: STAND-V200F
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Arm
C(x1)
Pole
I(x2)
M3x8
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x2)
VESA Plate
E(x1)
Pole Cable
Clip
F (x4)
Arm Wire
Clip
G(x1)
Pole Cap
H (x3)
M6x12
K(x1)
4mm Allen
Wrench
J(x2)
Knob
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
L(x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M4x16
M-C (x8)
M5x12
M-D (x8)
M5x16
M-E (x8)
Washer
M-F (x8)
Spacer

3
ASSEMBLY STEPS
STEP 1
Attach the pole cap (G) to the top of the pole (C).
TOOLS NEEDED
Phillips
Screwdriver
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
STEP 2
Attach the pole (C) to the base (A) using M6x12 bolts (H) and tighten using the 4mm Allen wrench (K).
PER ARM

4
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plates (D) to the monitors using
bolts (M-A or M-C) and washers (M-E). Tighten
with a Phillips screwdriver.
STEP 4
Slide the pole cable clip (E) and arm (B) onto the pole (C) and tighten using the 6mm Allen wrench (L).
Attach the arm cable clips (F) to the arm (B).

5
STEP 4 (Continued)
STEP 5
OPTION B: Curved Back Monitor
Attach the VESA plates (D) to the monitors using
bolts (M-B or M-D), washers (M-E) and spacers (M-F).
Tighten with a Phillips screwdriver.
Slide the VESA plates (D) onto the arm (B) and secure using the knobs
(J) with M3x8 bolts (I).

6
STEP 6
Tighten or loosen the tilt joint using the 6mm Allen wrench (L).
STEP 7
Route cables through the cable management clips.

7
STEP 8
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
Adjust as Desired
Turn the knobs (J) by hand or using the 6mm Allen wrench (L) to adjust the monitor height for
leveling. Store tools in the cable clip.

LAST UPDATED: 04/02/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303